Digital Commons Network^™

Shop Level Maintenance Of Inertial Platforms Without A Surveyed Site, Max E. Bott

Masters Theses

"The initial installation of a rotary tilt table for an aircraft inertial navigation system test facility includes accurately aligning the rotary tilt table to local level and true north coordinates. The survey techniques presently employed are an encumbrance during installation and complicate remote deployment. The objective of this thesis is to determine if an inertial platform or platforms can practically be used to replace the role of the survey techniques in the rotary tilt table alignment. The construction, capability and operation of a rotary tilt table are reviewed. The tests necessary to test and calibrate an inertial platform are outlined, …

A Hardware And Software Interface Between A Graphics Terminal And The Scc 650 Computer, George Irvin Rhine Jr.

Masters Theses

"This paper describes the design of a digital interface between a graphic terminal and the SCC-650 computer. The graphic terminal-computer combination can be used as a stand alone system for small applications or can be used as a satellite processor for a larger system such as the IBM System 360, The interface is designed utilizing DTL NAND type integrated circuits. Its primary functions may be divided into three main categories: (1) to give level conversion, (2) control, and (3) data manipulation. All requests for data transfers are initiated by the computer, the interface then assumes a control mode which handles …

Triangular Signal Stabilization Of Nonlinear Systems, Kamaleddin Yadavar Nikravesh

Masters Theses

"Many nonlinear systems display self-sustained oscillations which are often undesirable. The stabilizing effect of a high frequency input signal on an oscillating system with one nonlinearity is determined by the characteristics of the nonlinear element in the system, the linear portion of the system and the amplitude of the signal. This investigation has been concerned with the effect of a triangular wave stabilizing signal on these self oscillations. The equivalent gains for several common nonlinearities are derived. The pseudo describing function introduced by Oldenburger and Boyer for sinusoidal stabilization has been extended to the triangular wave case, and it is …

The Anodic Dissolution Of Tungsten, James W. Johnson, Cheng-Hsiao Wu

Chemical and Biochemical Engineering Faculty Research & Creative Works

The anodic dissolution of tungsten was studied in H₂SO₄-K₂SO₄ solutions (pH = -2 to 2.5) and K₂SO₄-K₂CO₃-KOH solutions (pH = 11.5 to 14.5) at 25 C. Faradaic efficiency studies in basic solutions showed the metal to be oxidized to the +6 state. In acid solutions, a thick protective film of yellow WO₃ was formed. Polarization curves possessed linear Tafel regions (slope ~ 2.3 RT/F) at potentials slightly more positive than the rest potentials. An anodic dissolution mechanism is proposed which involves a surface film …

The Design Of A High Temperature Thermoelectric Generator Element Using Silicon Carbide, John Talmage Barrow Jr.

Masters Theses

"This report presents the design of an optimum, high temperature silicon carbide thermoelectric generator element. The analytical efforts have been divided into three basic parts, the development of the theory, the accumulation of the data, and the optimization of the design. The first step in the theory development was the derivation of accurate design equations. With this done, the design philosophy and computer program were constructed, the latter utilizing a subroutine to contain the design equations. The data was obtained from a survey of many references and, for the most part, was found to be inexact, requiring the consideration of …

Calculation Of Eddy Current Loss Of A Disc, Kou Quen Chang

Masters Theses

"A method is presented to calculate the eddy current losses of a uniform disc with an opening in the center and excited by a circular current loopage First, the disc is subdivided into smaller concentric rings, then the self-inductances, the mutual inductances between these smaller rings, the mutual inductances between the excitation coil and the smaller rings, and the resistance of the rings are calculated. Next, the eddy current flowing in each ring is obtained by solving a complex matrix equation of the form [X] [I] = [V] where X is the impedance matrix, I is the eddy current matrix, …

Low Frequency Lumped Element Directional Couplers, Constantine Rodolph Jenkins

Masters Theses

"Lumped element directional couplers are desirable at frequencies below the VHF range because they eliminate the large physical size necessary for the distributed element directional couplers. The purpose of this work is to describe the theory and design of such low frequency lumped element directional couplers. A model for the coupler is developed and the equations which describe it are derived. Scattering matrices for one and two section couplers are obtained. Computer solutions for three section couplers are presented. Experimental results for one, two, and three section couplers are presented and comparison with theory are made. Comparisons of theoretical and …

An Analysis Of Solar Noise Outbursts And Their Application To Space Communication, Marion Francis Moen

Masters Theses

"A relationship between sunspot activity, solar flare activity and noise outbursts is presented. Five different types of interference radiation in the 10MH_z to 30,000 MH_z frequency band are discussed. Data obtained by solar radio astronomy are analyzed to determine the extent of solar noise outbursts as a function of sunspot activity. An application of the burst data to future space communication is given"--Abstract, page ii.

The Effect Of Channel Errors In The Differential Pulse-Code-Modulation Transmission Of Sampled Imagery, Roger J. Arguello, Harvey R. Sellner, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

This Paper Presents an Analysis, Simulation, and Discussion of the Effects of Communication Errors on Four-Bit Differential Pulse-Code Modulation (DPCM) Sampled Imagery. Simulations Are Presented that Describe the Effects of Inserting Periodic "PCM Updates" in Order to Correct Communication Errors in the DPCM Transmission of Photographic Scenes that Have Been Scanned and Sampled at the Nyquist Rate. Copyright © 1971 by the Institute of Electrical and Electronics Engineers, Inc.

Deriving Dc Machine Torque By The Principle Of Virtual Work, George Mcpherson

Electrical and Computer Engineering Faculty Research & Creative Works

The purpose of this paper is to fill a gap which exists in the "textbook" theory of dc machines. The paper shows that the usual expression for dc machine torque can be obtained from the direct application of the principle of virtual work to the machine, making the traditional assumptions. The method provides additional benefits in that it demonstrates the reluctance torque which results from the saliency of the field structure and shows that compensating windings have no effect on the torque under the assumed linear conditions. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Electrical Engineering Education In An Industrial Laboratory, J. Derald Morgan

Electrical and Computer Engineering Faculty Research & Creative Works

This paper describes a unique electrical engineering laboratory course. This laboratory is an example of industry-uni-versity cooperation in engineering education. The organization and operation of the course is outlined and explained. The educational benefits derived from such cooperation between industry and the university are briefly detailed. These benefits are extended to the students, the university, the faculty, and the participating industry. This paper provides the framework and challenge to industry from which other laboratory experiences can be conceived and developed. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

A Gamma-Level Portable Ring-Core Magnetometer, Stanley V. Marshall

Electrical and Computer Engineering Faculty Research & Creative Works

A four-transistor circuit is described for a battery-operated magnetometer that has 0.1 γ resolution using t-in diameter 4–79 or 6–81 Mo-Permalloy tape cores of 20–40 Mx capacity. The center-tapped drive winding also serves as the sense winding, simplifying the sensor assembly. Some signal-to-noise results are presented to illustrate the fairly wide difference that may exist between cores of the same cross section and to demonstrate the advantage of reducing core area. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Raman Scattering From Localized Vibrational Modes In Gap, D. T. Hon, W. L. Faust, W. G. Spitzer, P. F. Williams

P. F. (Paul Frazer) Williams Publications

High-frequency localized vibrational modes of impurities in a III-V compound have been observed by Raman scattering. Three lines from the GaP samples closely correspond to some loccal modes previously reported in infrared studies, and depolarization measurements tend to confirm their proposed assignments. We describe several attractive features of this method for the study of semiconductor impurities.

Longitudinal Modes In A High-Gain Laser, Lee W. Casperson, Amon Yariv

Electrical and Computer Engineering Faculty Publications and Presentations

In lasers employing high‐gain narrow‐linewidth transitions the theory predicts major departures of the mode‐splitting frequencies from their low‐gain values as well as a new type of mode splitting. The first of these effects consisting of a reduction by a factor of 2.5 of the mode splitting in a xenon 3.51‐μ laser is observed experimentally.

Reliability Aspects Of Semiconductor Surface Protective Coatings, Robert Edward Mcmillan

Dissertations

This research was directed towards the occurrence and im-portance of surface leakage in reverse biased semiconductor diodes and the relation of this leakage to the reliability of a device under use conditions. As a result of this study, it is possible to predict one important leakage mechanism after such back-biased diode units have been subjected to long periods of temperature and humidity. This theory is consistent with tests of commercially available units, some of which have very slight surface leakage and others very large surface leakage.

Further, the usefulness of various possible passivating coatings is critically analyzed on the basis …

A Study Of The Secant Law For Sporadic E, Ruey-Yuan Han

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The secant law is the relationship between the frequencies of a vertically incident wave and an obliquely incident wave that are reflected from the same level (i.e., density) of a stratified ionosphere. This thesis investigates the validity of the secant law applied to sporadic E.

Sporadic E data from two backscatter sounders and one vertical incidence ionosonde located in Japan were studied to test the validity of the secant law. The B-scan photos of the backscatter sounders were searched for E_s patches which were then compared with the sporadic E parameters defined for vertical incidence ionograms.

Finally, two theoretical …

Electrical Lighting Design, Thermthip Chamarakula

Graduate Research Papers

In any given space for lighting design, each space presents a unique lighting problem which must be studied. These problems can be considered as physical characteristics of the space and its occupancy and usage.

With respect to. these problems a number of questions must be asked.

1. What are the actual seeing tasks?

2. Is the usage uniform or are different areas utilize< for seeing tasks of varying severity?

3. How should the lighting equipment be?

4. How can the proper quantity and quality of light be established?

5. Will the area be used during both daylight hours and at night, and, if so, are the …

The Evaluation Of Radar Guided Missile Performance Using Various Target Glint Models, Franklin Delano Hockett

Masters Theses

"A radar guided missile seeker approaching a target arrives at a crossover point beyond which the entire target is illuminated by the missile seeker's radar antenna beam. When this occurs, for a complex target, the radar senses a time changing target center location which may greatly complicate the terminal tracking portion of the seeker's flight. This thesis documents various glint models in use today and compares the performance of these models by using a seeker model to determine the effect of glint on terminal tracking performance. A large volume of data has been compiled describing various radar characteristics of complex …

A Simulation And Diagnosis System Incorporating Various Time Delay Models And Functional Elements, David Michael Rouse

Doctoral Dissertations

"The application of digital simulation to all phases of digital network design is considered here as oppossed [sic] to development of simulation for one or two restricted parts of the digital process. For this reason a simulator is presented which can be consistent by varying the level of expression from the simulation of architectural structures to such detailed simulation requirements as race analysis of asynchronous sequential circuits. In order to make system simulation more than just an idea, it must be capable of handling large circuits in reasonable times. It is demonstrated that functional simulation has the potential to increase …

Re-Design Of Cloud Chamber Instrumentation, Stanley Forrest Vaninger

Masters Theses

"Instrumentation and a new valving system is designed and built for use with an expansion type cloud chamber. Digital equipment is used for timing to improve reliability, accuracy, and flexibility, and a servo system is built using a lead compensator circuit which improves the servo system typically used with cloud chambers. Special care was taken to eliminate the sources of noise that appear in the amplified signal from the pressure transducer. The equipment needed to measure, record, and calibrate the pressure inside the chamber is built"--Abstract, page ii.

An Approximate Min-Max Solution To The Identification Problem, Richard Loyd Warren

Masters Theses

"A technique based on the min-max error criterion is proposed for identifying a dynamic system in terms of a discrete-time model from the system response to a deterministic input. A linear, single-input/single-output, lumped-parameter, time-invariant (at least during the measurement interval) system is assumed. Although the resulting problem is non-linear, it is shown that linear programming techniques are applicable if a realistic approximation is made. The technique is implemented on the digital computer and evaluated by considering a number of typical discrete-time systems. The effects of additive noise are also considered"--Abstract, page ii.

Next-State Equation Generation For Asynchronous Sequential Circuits - Normal Mode, Gregory Martin Bednar

Masters Theses

"This paper describes the known methods of generating next-state equations for asynchronous sequential circuits operating in normal fundamental mode. First, the methods that have been previously developed by other authors are explained and correlated in a simple and uniform language in order that the subtle differences of these approaches can be seen. This review is then followed by a development of a new method for generating minimal next-state equations which has some advantages over the previous methods. From the comparison of the previous known methods, it is noted that any one of these methods may be desirable for certain designs …

The Dinary Numerical System And Its Applications To Modern Parallel Processing Computers, Hai Chi Koo

Masters Theses

"The Dinary Numerical System (DNS) is an extension of Binary Numerical System. By utilizing the newly developed Large-Scale-Integration technology, DNS can be implemented as a new concept of computer organization which has the merits of parallel processing. DNS consists of three field elements: they are -1, 0, and +1. Since DNS representation is not necessarily unique, new algorithms to generate the number of representations and all equivalent representations are presented in this paper. A Block-Oriented-Computer (BOC) is developed as an array of computing systems. For each of the systems, the arithmetic unit is essentially a modified Digital Differential Analyzer. The …

An Analysis Of A Synchronization Scheme For 180° Biphase Modulated Signals, James Joseph Spence

Masters Theses

"The problem of analyzing a synchronization system for demodulation of 180° biphase modulated signals is considered in this thesis. The system considered utilizes the so-called squaring loop technique. Techniques derived from the theory of Markov processes are utilized in the analysis of the system. In particular the "fluctuation equation" approach for non-Markovian processes is used. After the analysis of the system is performed, an expression fro the bit error probability is obtained from knowledge of the phase error density function"--Abstract, Page ii.

Integrating An Oscilloscope Into A General Purpose Automatic Test System, William Charles Bauer

Masters Theses

"The General Purpose Automatic Test System was developed for the Air Force as a system to automatically test and fault isolate an electronic unit under test. The Test System is a building block concept and this paper developed the hardware and programming software necessary to integrate an oscilloscope into the system. A Tektronix Type 564 oscilloscope with a Tektronix Type 3A5 Programmable Amplifier and a Tektronix Type 3B5 Programmable Time Base was used. A prototype of the digital and analog interface between the Test System and the Tektronix System was built and demonstrated. The Oscilloscope Building Block displays waveforms only …

Computerized Methods For Estimating Heating-Cooling-Ventilating System Usage In All-Electric Buildings, Carl William Glaser

Masters Theses

"This thesis develops a method and a resulting computer program for estimating the energy input required by the heating-cooling-ventilating system of a building. The computer program has the ability to model the ventilating system and all the inefficiencies introduced when the heating system is allowed to fight the cooling system to provide temperature control within the conditioned space. The program also can consider mechanical heat reclaim accurately, making the consideration on a time of need versus a time of occurrence basis. The program is written to utilize input data in rather simplified form. This allows the program to be used …

A Study Of Microstrip Transmission Line Parameters Utilizing Image Theory, Joseph Louis Van Meter

Masters Theses

"This paper is a theoretical investigation of the potential, electric field, capacitance, and characteristic impedance of the open strip transmission line or microstrip configuration based upon the classical Thomson Image Technique. It provides the basis for determination of the charge distribution on the strip and reports impedance values which compare favorably both with experimental values and theoretical work in the current literature"--Abstract, page ii.

An Explicit Simulation Of Overland Flow, Glendon Taylor Stevens

Masters Theses

"Computer simulation of overland flow requires a mathematical model which converges to a true solution. This paper presents a method, based on measurable physical parameters, which insures convergence of a fixed grid explicit numerical solution. Analysis of a wide range of overland flow plane parameters has resulted in an equation of the form Δt = 0. 2 ΔX/S_o, for the time step increment. This equation provides values for Δt that will insure stability and convergence of the fixed grid explicit numerical method of solving the spatially varied unsteady flow equations. The effect of subarea shape on the rising …

Fault Detection In Asynchronous Sequential Circuits, Jeng-Chuan Kau

Masters Theses

"As the asynchronous sequential circuit has become more and more important to digital systems in recent years high reliability and simple maintenance of the circuit is stressed. This paper presents a fault-detection algorithm which will be applicable to most of the practical asynchronous sequential circuits. The asynchronous sequential circuit is treated from the combinatoric point of view. First the minimal set of states, both stable states and unstable states, sufficient to detect all possible faults of the circuit is found from the fault table. Then a test sequence is generated to go through these states. It is assumed that testing …

A Mathematical Model For The Neutron Dependence Of Neutral Base Region Recombination, Jonas Bereisa Jr.

Masters Theses

"A discrete, deterministic, mathematical model is developed for the neutral bulk base region of graded base devices which accounts for both the effects of recombination and the built-in electric field in the bulk base region at low, intermediate, and moderate current/injection levels. This model is applied to a study of neutron radiation effects in double diffused silicon transistors. Exact expressions are developed for the injected emitter, base and collector currents, the base recombination term, and the ratio of base current increase to collector current decrease as functions of device geometry, impurity profile, and neutron fluence. Neutron-induced current gain degradation is …