Digital Commons Network^™

Control System Design Program Based On Cascade Compensation, Fredrick Ishengoma

Tanzania Journal of Engineering and Technology (TJET)

CAD is becoming more widely accepted in the design and analysis of control systems. A program has been developed for analyzing single-input single-output linear time-invariant control system. The application of the progranl for frequency domain design of cascaded phase lead and phase lag coinpensators is briefly discussed. Two examples to illustrate the program are presented.

Limaçon Of Pascal Locus Of The Complex Refractive Indices Of Interfaces With Maximally Flat Reflectance-Versus-Angle Curves For Incident Unpolarized Light, R. M.A. Azzam

Electrical Engineering Faculty Publications

For an interface between two isotropic media the power reflectance R_v (ø) is an even function, R_v (ø) = R_v (--), of the angle of incidence ø; hence all the odd derivatives, R_v⁽ⁿ⁾ = dⁿ R_v /døⁿ (n odd), are identically 0 at ø = 0, independent of the incident polarization v. When the incident light is unpolarized (v = u), the second derivative, R_u⁽²⁾, is also 0 at ø = 0, so that the flatness of the R_u -versus-ø curve …

Performance Evaluation Of Spread Spectrum System With Cochannel Interference Through A Nonlinear Channel, Yong H. Kim

Dissertations

This thesis deals with the problem of more than one subscriber transmitting data signals through a common satellite repeater using code division multiplexing to separate the signals. We are concerned with the problem of amplifying two DS spread spectrum signals, both QPSK or BPSK modulated, in a common device in which limiting occurs. One signal is considered the signal we desire to receive, and the other, having the same nominal carrier frequency with a small random offset, is considered to be a cochannel interferer. The case of a cochannel interferer on the uplink and downlink in QPSK signalling and BPSK …

Analysis Of Electric Field On Surface Of An Atomically Sharp Field Emitter, Ziyan Cheng

Theses

In this thesis, exact calculation and computer simulation of an atomically sharp emitter are presented. In the theoretical analysis, the cathode-anode or cathode-gate complex is modeled for cone- and wedge-shaped emitters so that exact solution can be obtained. The exact solution reveals that the field on the emitter surface depends not only on the sharpness of the emitter, but also on the global geometry of the field emitter, gate, and anode complex. This finding is contrary to a widely accepted concept that field is predominantly determined only by local curvature of the tip.

The theoretical results are confirmed by computer …

Modeling And Performance Of Token Bus Lan With Petri Nets, Zhenggang Pan

Theses

A token bus local area network (LAN) is analyzed by Generalized Stochastic Petri Nets (GSPN). The GSPN models of both a single station and LAN for four types of service schemes are obtained and their liveness property is proved. The network performance parameters comprise throughput and delay. The performance analysis for both symmetric and asymmetric single-service systems is conducted for varying load. In order to analyze a token bus LAN with a large number of stations, an approximation method is developed to resolve the .state space explosion problem. A token bus LAN with twenty-one stations is used to show the …

Optimization Of A 3-Micron Bccd Process For High Density Ccd Registers, Mark Ratner

Theses

In July 1991, Dr. Walter F. Kosonocky proposed a High-Frame-Rate-CCD Imager. The design of the imager is such that the CCD channel width be 3-microns and capable of handling at least 3000 - 5000 electrons per square micron. Using process (SUPREM III) and device (PISCES IIB) simulations, charge handling capacities as a function of implant energy and junction depth were studied. Arsenic implants ranging from 100 to 200keV were driven-in to obtain junction depths between 0.40µm and 0.80µm. As a result of this work it was determined that charge handling capacities as high as 9400 electrons/µm² were achievable with …

Comparing Techniques Of Mapping Pyramid Algorithms Onto The Hypercube : A Case Study For The Connection Machine, Muhammad Ali Siddiqui

Theses

The pyramid structure is most widely used for low-level and intermediate-level image processing and computer vision because of its efficient support of both local and global operations. However, the cost of pyramid computers (PC) may be very high. They also do not support the efficient implementation of the majority of the scientific algorithms. In contrast, the hypercube network has widely been used in the field of parallel processing because it offers a high degree of fault tolerance, a small diameter and rich interconnection structure that permits fast communication at a reasonable cost. Thus, several algorithms have been developed for the …

A New Method To Optimize The Satellite Broadcasting Schedules Using The Mean Field Annealing Of A Neural Network, Youyi Yu

Theses

This thesis reports a new method for optimizing satellite broadcasting schedules based on the Hopfield neural model in combination with the mean field annealing theory. A clamping technique is used with an associative matrix, thus reducing the dimensions of the solution space. A formula for estimating the critical temperature for the mean field annealing procedure is derived, hence enabling the updating of the mean field theory equations to be more economical. Several factors on the numerical implementation of the mean field equations using a straightforward iteration method that may cause divergence are discussed; methods to avoid this kind of divergence …

A New Approach To The Decomposition Of Incompletely Specified Functions Based On Graph Coloring And Local Transformation And Its Application To Fpga Mapping, Wei Wan

Dissertations and Theses

The thesis presents a new approach to the decomposition of incompletely specified functions and its application to FPGA (Field Programmable Gate Array) mapping. Five methods: Variable Partitioning, Graph Coloring, Bond Set Encoding, CLB Reusing and Local Transformation are developed in order to efficiently perform decomposition and FPGA (Lookup-Table based FPGA) mapping. 1) Variable Partitioning is a high quality hemistic method used to find the "best" partitions, avoiding the very time consuming testing of all possible decomposition charts, which is impractical when there are many input variables in the input function. 2) Graph Coloring is another high quality heuristic\ used to …

An Improved Formulation Of The Temperature Dependence Of The Gummel-Poon Bipolar Transistor Model Equations, Chorng-Lii Liou

Dissertations and Theses

A number of shortcomings were found after complete derivation of the temperature dependence of equations, and the expressions related to the Early effect in the present Gummel-Poon 2 model, as implemented in the TEKSPICE program. The formulation and application of improved model equations is presented, followed by a detailed comparison of the existing model with the one developed in this work.

Review: 'Optical Fiber Communications' (2nd Edition), By Gerd Keiser, Bradley D. Duncan

Electro-Optics and Photonics Faculty Publications

If first impressions are worth anything (and they usually are), I would have to admit that my first impression of the second edition of Gerd Keiser's now popular text Optical Fiber Communications was quite good. My compliments are hereby extended to the publisher for choosing a rather handsome cover and dust jacket. It stands in strong contrast to the text's first edition, which still ranks as probably the ugliest book I own, with color choices ranging from dull cream and "baby" blue to pale pink! I am now happy to say that this older version has been discretely·retired to the …

Digital Model Of A Generic Infrared Tracker, James Michael Brown

Graduate Theses - Electrical and Computer Engineering

Personal computer based simulations are popular because of the wide availability of personal computers. In this thesis, a simple simulation model of a generic infrared tracker is developed for the personal computer. This thesis first centers on the definition of a generic infrared tracker and the development of a tracker model. The remainder of this thesis is a description of the personal computer based computer simulation model, and a discussion of results of simulation runs to characterize the tracker model response. The conclusion of this thesis is that the simple simulation model serves both as a prototype for developing a …

A Survey Of Electronic Environmental Controllers, Richard S. Gates, Douglas G. Overhults, Larry W. Turner

Biosystems and Agricultural Engineering Faculty Publications

Sixteen commercially available electronic environmental controllers were evaluated. The units were classified according to enclosure type, analog versus microprocessor based control, power supply, sensors, alarms, control relays and triac output, interval timers, outside temperature feedback, and retail price. An assessment of these controllers indicated several critical limitations in the application of this technology.

The use of integrated controllers for animal production has the potential for substantial improvements in production efficiencies. If the limitations observed in the present controller technology, as represented by this sample, are addressed, industry acceptance of the technology can be accelerated. A uniform standard to address this …

Finite-Dimensional Approximations Of Unstable Infinite-Dimensional Systems, G. Gu, P. P. Khargonekar, E. B. Lee, Pradeep Misra

Electrical Engineering Faculty Publications

This paper studies approximation of possibly unstable linear time-invariant infinite-dimensional systems. The system transfer function is assumed to be continuous on the imaginary axis with finitely many poles in the open right half plane. A unified approach is proposed for rational approximations of such infinite-dimensional systems. A procedure is developed for constructing a sequence of finite-dimensional approximants, which converges to the given model in the L infinity norm under a mild frequency domain condition. It is noted that the proposed technique uses only the FFT and singular value decomposition algorithms for obtaining the approximations. Numerical examples are included to illustrate …

On Planar Routing Of Multi-Terminal Nets In Vlsi Physical Design, Jahangir A. Hashmi

Masters Theses

In this thesis, we study two problems related to the physical design of VLSI circuits. One problem is related to the VLSI global routing and the other is related to the detailed routing in a bounded region.

We consider the routing of multiple multi-terminal nets on a single layer. We suggest a new approach for this problem. Our approach is based on simultaneously finding a forest of k non-intersecting spanning trees. We present an O(n^3) algorithm for finding two spanning trees corresponding to two nets on a single layer.

We also study the problem of finding a minimum Steiner tree …

A Study Of Numerical Integration Techniques For Use In The Companion Circult Method Of Transient Circuit Analysis, Charles A. Thompson

Department of Electrical and Computer Engineering Technical Reports

Circuit transient analysis packages such as SPICE and EMTP are very widely used, but detailed information on the internal structure and error characteristics for these software packages is lacking. Both SPICE and EMTP rely on numerical integration to approximate the transient response of circuit elements. The numerical integration methods used in the packages are not necessarily the most accurate approximations to the actual response of a circuit. The study of these numerical integration methods and their error characteristics is the focus of this thesis. Comparisons are made between several methods in terms of accuracy and stability as well as algorithm …

Formant Estimation From Dctc's Using A Feedforward Neural Network, Shubhangi U. Kelkar

Electrical & Computer Engineering Theses & Dissertations

Formants are the natural frequencies of the human vocal tract. Existing methods for estimating formants from speech signals are computationally complex and subject to errors for certain type of speech sounds. This thesis describes a method for estimating vowel formant frequencies from Discrete Cosine Transform Coefficients (DCTC's), a form of cepstral coefficients, using a feedforward neural network with back-propagation training. Experimental results are based on a large multispeaker data base. The results are obtained for both a linear transformation and a feedforward neural network with a nonlinear hidden layer. In general, the neural network transformation is superior to the linear …

Comparison Of Synchronization Techniques For The Afit Direct Sequence Spread Spectrum System, Edward A. Bednar

Theses and Dissertations

The purpose of this study is to analyze and evaluate the performance of several code synchronization methods that could be used in the Air Force Institute of Technology's (AFIT) Direct-Sequence Spread Spectrum (DSSS) communication system. These methods include the sliding correlator, transmitted reference, sequential estimation, and three types of matched filters. The matched filters are the baseband matched filter, delay line matched filter, and the convolver. The criteria used for the evaluation of these synchronization methods are theoretical synchronization times and probability of bit-error. Advantages and disadvantages of each synchronization method are described and a method is recommended to be …

Transient Overvoltage Testing Of Environmental Controllers, Richard S. Gates, Larry W. Turner, Douglas G. Overhults

Biosystems and Agricultural Engineering Faculty Publications

The integrated electronic control system will provide a new method for the day-to-day management of environmental control of animal production systems. No standards are currently accepted for transient overvoltage protection of these controllers. To assess the adequacy of existing designs, a test circuit was designed and used for a transient open circuit over-voltage waveform (ANSI/IEEE C62.41-1980) of 16 environmental control units: a maximum spike of 770 V was applied to the power supplies, and a spike up to 100 V was applied to temperature sensor lines. For these relatively mild tests, no failures were noted due to power supply transients, …

Hardware-Verification Through Logic Extraction, Michael A. Dukes

Theses and Dissertations

A Prolog-based system is described which employs logic-extraction to perform hardware-verification. The extraction rules are built automatically from hierarchical structural VHDL models, enabling the equivalence of a structural VHDL description and a layout specification to be verified. Pin-to-pin critical- path analysis is performed within the logic-extraction process; many noncritical paths are pruned early, making pin-to-pin critical path analysis of large circuits feasible. It is demonstrated that a design methodology based on logic extraction, VHDL, and a layout tool can provide a fabricated functionally- correct IC design without circuit-level or switch-level simulation. This methodology is shown to be practical for VLSI …

Three-Dimensional Insulated Gate Bipolar Transistor (Igbt) Development, P.V. Gilbert, G.W. Neudeck

Department of Electrical and Computer Engineering Technical Reports

A new insulated gate bipolar transistor structure, the 3D-IGBT, is presented. The 3D-IGBT utilizes selective epitaxial silicon to form a top contacted anode and still retain the cellular structure of vemcally oriented devices. The 3D-IGBT , unlike other fully integrable power devices, exploits the merits of cellular structure to increase its packing density and thus reduce its on-resistance per unit area. It also eliminates the parasitic JFET resistance found in vertical IGBT's. To integrate the 3D-IGBT with low power devices, the QDI method of device isolation is also presented. QDI uses a combination of JI and DI to electrically isolate …

Achieving A Given Reflectance For Unpolarized Light By Controlling The Incidence Angle And The Thickness Of A Transparent Thin Film On An Absorbing Substrate: Application To Energy Equipartition In The Four-Detector Photopolarimeter, R. M.A. Azzam, Kurt A. Giardina

Electrical Engineering Faculty Publications

At a given wavelength λ we determine all possible solution pairs (ϕ, ζ) of the incidence angle ϕ and the thickness ζ of a transparent thin film on an absorbing substrate that achieve a given unpolarized light reflectance R_u. The trajectory of the point that represents a solution pair in the ζ, ϕ plane depends on the optical properties of the film and substrate and on whether R_u is greater than or less than the normal-incidence reflectance -R₀ of the bare substrate. When R_u > - R₀, the specified reflectance is achieved over a …

Detection, Location, And Quantification Of Structural Damage By Neural-Netprocessed Moire Profilometry, Barry G. Grossman, Frank S. Gonzalez, Joel H. Blatt, Jeffery A. Hooker

Electrical Engineering and Computer Science Faculty Publications

The development of efficient high speed techniques to recognize, locate, and quantify damage is vitally important for successful automated inspection systems such as ones used for the inspection of undersea pipelines. Two critical problems must be solved to achieve these goals: the reduction of nonuseful information present in the video image and automatic recognition and quantification of extent and location of damage. Artificial neural network processed moire profilometry appears to be a promising technique to accomplish this. Real time video moire techniques have been developed which clearly distinguish damaged and undamaged areas on structures, thus reducing the amount of extraneous …

A Lower-Bound For The Error-Variance Of Maximum-Likelihood Delay Estimates Of Discontinuous Pulse Waveforms, Kurt Louis Kosbar, Andreas D. Polydoros

Electrical and Computer Engineering Faculty Research & Creative Works

A new lower bound is developed for the error variance of maximum-likelihood time-delay estimation when the received signal is a square pulse, corrupted by additive white Gaussian noise. The bound is generated by combining concepts previously developed for a special class of stochastic processes, induced by the signal model. For moderate signal to noise ratios, the new bound is significantly tighter than previously known ones.

Design And Analysis Of Electrical Circuits That Produce Fractional-Order Differentiation, Richard N. Hughes

Theses and Dissertations

Two half-order differentiator circuit designs were investigated and their electrical performance evaluated (Oldham and Oldfield). Initially, each circuit design was computer modelled and simulated using the HSPICE computer analysis program. Then, each circuit design (Oldham and Oldfield) was fabricated with two different component technologies. This resulted in four circuits, realized on printed circuit boards, to be evaluated--Oldham discrete component; Oldham hybrid component; Oldfield discrete component; and Oldfield surface mount component. The characterizations of each circuit's electrical performance is documented with time, phase, gain, noise and spectrum responses. A comparison of each circuit's performance versus the design criteria and computer model …

Developing Cmmca Flight Profiles For Cruise Missile Tracking, Andrew C. Hachman

Theses and Dissertations

The Air Force has recently acquired two aircraft dedicated for cruise missile tracking. These aircraft, known as the Cruise Missile Mission Control Aircraft (CMMCA), are responsible for collecting data from the missile and United States. Due to tracking and positively controlling the missile during live fire testing over the western the limited tracking radar range and the flight characteristics of the CMMCA, tracking cruise missiles through complex maneuvers is not always possible. A FORTRAN optimization, based on flight simulation and optimal control theory, was written in a prior thesis effort in order to determine optimal CMMCA flight profiles for tracking …

Finding A Maximum-Density Planar Subset Of A Set Of Nets In A Channel, Ronald I. Greenberg, Jau-Der Shih

Computer Science: Faculty Publications and Other Works

We present efficient algorithms to find a maximum-density planar subset of n 2-pin nets in a channel. The simplest approach is to make repeated usage of Supowit's dynamic programming algorithm for finding a maximum-size planar subset, which leads to O(n^3) time to find a maximum-density planar subset. But we also provide an algorithm whose running time is dependent on other problem parameters and is often more efficient. A simple bound on the running time of this algorithm is O(nlgn+n(t+1)w), where t is the number of two-sided nets, and w is the number of nets in the output. Though the worst-case …

Model-Based Target Recognition Using Laser Radar Imagery, Robert Y. Li

Department of Electrical and Computer Engineering: Faculty Publications

Autonomous target recognition can be assisted by using CO2 laser radar data. Of these data, range data provide 3-D geometric information and Doppler data boundaries of moving targets. A powerful 3-D feature extraction algorithm based on the Hough transform is used to obtain the orientations and dimensions of the target. This information is then utilized by an inference procedure that recognizes targets based on the available evidence from the sensory data. The experimental results using actual laser radar imagery are successful and the procedure can be used for the future development of a model-based system for target recognition.

Analysis Of Algorithms For Velocity Estimation From Discrete Position Versus Time Data, Ronald H. Brown, Susan C. Schneider Phd, Michael G. Mulligan

Electrical and Computer Engineering Faculty Research and Publications

Algorithms for constructing velocity approximations from discrete position versus time data are investigated. The study is limited to algorithms suitable to provide velocity information in discrete-time feedback control systems such as microprocessor-based systems with a discrete position encoder. Velocity estimators based on lines per period, reciprocal-time, Taylor series expansion, backward difference expansions, and least-square curve fits are presented. Based on computer simulations, comparisons of relative accuracies of the different algorithms are made. The least-squares velocity estimators filtered the effect of imperfect measurements best, whereas the Taylor series expansions and backward difference equation estimators respond better to velocity transients.

Series Compensation Investigation On The Hydro-Quebec And Nypa 765 Kv Transmission System : Modeling And Stability Analysis, Hans J. Candia

Theses

This thesis presents a mathematical approach for raising the power steady state stability limit by adding series capacitive compensation to a transmission line. The effect of series capacitive compensation and degree of compensation were investigated in detail. The power system studied includes an automatically controlled power system, IEEE Type I.

The results of the actual and theoretical steady state stability limits for a given series capacitance location and degree of compensation were obtained by applying the frequency domain technique. The natural frequencies of each compensated power network were examined.

The best location for series capacitive compensation is proposed which is …