Digital Commons Network^™

Investigation Of Pathophysiologic Trends In Caucasian And Afro-American Hypertensives By Means Of Heart Rate Variability Recording During Upright Tilt-Table Testing, Jose F. Torrealba

Theses

The incidence of hypertension is more prevalent among the Afro-American population than the Caucasians and there is not a satisfactory explanation for this discrepancy.

Heart Rate Variability (HRV) has been demonstrated to reflect the relative activities of the sympathetic (SMP) and parasympathetic (PSMP) divisions of the autonomic nervous system (ANS).

This study consisted in comparing the HRV, as well as the blood pressure (BP) of four different groups during up-right tilt table testing. The subjects were grouped by age, gender, race and health condition. Analysis in time and frequency domain was applied to the data. In the frequency domain, the …

Electrochemical Preparation Of Rare Earth Functional Materials And Application Of Rare Earth To Electrochemistry, Qi-Qin Yang, Tong-Xiang Ye

Journal of Electrochemistry

The new progress and related mechanism of the electrochemical preparation of rare earth materials (magnets, magnetooptic materials, battery materials, luminescent devices, semiconductors, superconductors) and the application of rare earth to the electrochemical areas (e.g. electroplating, corrosion, electrosynthses) have introduced.

In-Situ Raman Spectroscopic Study Of The Oxidation And Reduction Of Ag Electrode In Na2So4, Yan-Xia Chen, Kai-Qi Huang, Zhong-Qun Tian

Journal of Electrochemistry

In-situ Raman spectroscopy combined with cyclic voltammogram measurements was used to investigate formation of oxygen species at Ag electrode surfaces during the oxidation and reduction process in 0.1 mol/L Na₂SO₄ solution. The time dependent Raman spectra show that at potentials positive of 0.2 V, adsorption of oxygen atom occurs, while at the potentials positive of 0.4 V, some oxygen atoms migrate into subsurface of the Ag electrode and the other form strongly bound oxygen on the surface through chemical bond. At the same potentials, part of the silver atoms are oxidized and form Ag₂SO_{4 …}

New Esr-Electrochemical Cell Designs For Coaxial Microwave Cavity, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

New cell designs for simultaneous electrochemical (EC) and electron spin resonance (ESR) measurements are reported for coaxial microwave cavity. Adjustable shieldings are introduced so that the working electrode can be much shorter than the full height of the cavity. Besides the traditional helical electrode, the working electrode can be cylinders made from metal plates, metallic meshes or even composite materials. The counter electrode can be placed either inside or outside the cavity. These features make the new designs more flexible than that previously reported. With a nonperforated cylindrical electrode, this cell can be used to determine the standard potential and …

Studies On The Transport Properties Of Zn2+ In The Zn/V2O5 Secondary Battery With Aqueous Medium, Jia-Hong Zhou, Kuan-Hong Xue, Gu-Ping Pan

Journal of Electrochemistry

The transport properties and the reaction mechanism of Zn²⁺ in the cathode material of Zn/V₂O₅ secondary battery with aqueous medium were studied by use of intermittent titration experiments and X-Ray diffraction analysis. The relations of some kinetic parameters to the discharge depth were discussed. The results of the experiments show that the cathodic discharge reaction is an intercalation process.

Electrode Process Of Lithium Ions On Aluminum Electrode In Molten Licl-Kcl, Shu-Zhen Duan, Cong-Sheng Guan, Qing-Rong Shi, Xin-Dong Wang

Journal of Electrochemistry

The Deposition mechanism of Lithium on aluminium electrode was studied by using linear sweep voltammetry and potential step method. The formation of α-solid solution was controlled by the diffusion of lithium within the aluminium substance. The formation of β-LiAl alloy was limited by the rate of forming the alloy at the legining, and by diffiusion of lithium through the β- LiAl alloy layer was limited by the rate of forming the alloy at the begining, and by the diffusion of lithium through the β-LiAl alloy later. Neucleation polarization for the formation of β-LiAl alloy was observed. This polarization is an …

Studies Of Surface Alloy As High Efficient Electrocatalyst For Glyoxylic Acid Synthesis, Sheng-Pei Chen, Sheng-Qing Xia, Shi-Gang Sun

Journal of Electrochemistry

/

System And Method For Improving Data Acquisition Capability In Spectroscopic Ellipsometers, Steven E. Green, Craig M. Herzinger, Blaine D. Johs, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

The present invention is applicable generally to Spectroscopic Rotatable and Rotating Element Ellipsometers which utilize a relatively large range of wavelengths. Disclosed is a system and method for controlling the polarization state of a polarized beam of light so that it is in a range where the sensitivity of a Polarization State Detector used to measure changes in said polarized beam of light resulting from interaction with a Sample System. to noise and measurement errors etc.. is reduced. Exemplified is a system. and method of use, for simultaneously setting both measured ellipsometric ALPHA, and ellipsometric BETA parameter values, (or equivalents), …

Impedance Of A Dipole Antenna In Ionospheric Plasma, Pavel Nikitin

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Different approaches to evaluating the behavior of the impedance of an electrically short dipole antenna in the ionosphere as a function of the driving frequency are discussed. The induced EMF method in quasi-static approximation is chosen for evaluating the impedance and explained in great detail. The E-region of the ionosphere is considered and the cold collisional plasma model is used.

The influence of a density gradient in plasma on the impedance is explored, and the possible current distributions on the surface of the antenna are considered, including the current distribution for the antenna with a gap. The conclusions are drawn …

Thermal Lattice Boltzmann Simulations Of Variable Prandtl Number Turbulent Flows, Min Soe, George Vahala, Pavol Pavlo, Linda L. Vahala, Hudong Chen

Electrical & Computer Engineering Faculty Publications

Thermal lattice Boltzmann (TLBE) models that utilize the single relaxation time scalar Bhatnagar, Gross, and Krook collision operator have an invariant Prandtl number. For flows with arbitrary Prandtl number, a matrix collision operator is introduced. The relaxation parameters are generalized so that the transport coefficients become density independent. TLBE simulations are presented for two-dimensional free decaying turbulence induced by a strongly perturbed double velocity shear layer for various Prandtl numbers.

Hermite–Sinusoidal-Gaussian Beams In Complex Optical Systems, Lee W. Casperson, Anthony A. Tovar

Electrical and Computer Engineering Faculty Publications and Presentations

Sinusoidal-Gaussian beams have recently been obtained as exact solutions of the paraxial wave equation for propagation in complex optical systems. Another useful set of beam solutions for Cartesian coordinate systems is based on Hermite–Gaussian functions. A generalization of these solution sets is developed here. The new solutions are referred to as Hermite–sinusoidal-Gaussian beams, because they are in the form of a product of Hermite-polynomial functions of either complex or real argument, sinusoidal functions of complex argument, and Gaussian functions of complex argument. These beams are valid for propagation through systems that can be represented in terms of complex beam matrices, …

Building Lms Adaptive Filters With Register-Based Fpgas, Li Ding

Electrical & Computer Engineering Theses & Dissertations

In this thesis, an 8-bit least mean squares (LMS) adaptive digital filter with 16 coefficients is implemented on a single FPGA, using the MaxPlus+2 design environment. The system is constructed as a hierarchical structure, using four different levels of design hierarchy. Subdesigns at each level of the hierarchy project are complied, fitted and simulated to test and verify their functional correctness. The complete system is tested and verified by checking the MaxPlus+2 simulator results against fixed-point integer arithmetic simulations written in Matlab. The resulting adaptive filter is subsequently mapped to the Alters FLEX I OK20TC144-3 device, resulting in a 14,500 …

Material Evaluation By Pulsed Diode Laser Optoacoustics, Xiaodong Xu

Electrical & Computer Engineering Theses & Dissertations

Pulsed diode laser optoacoustic diagnostics were carried out to characterize solid sample materials. The apparatus developed is compact, portable, cost-effective and therefore very promising for both industrial as well as laboratory applications. To our knowledge, this is the first time that optoacoustic characterization and measurement have been performed with a diode laser. The method was successfully applied to measure the thickness of a multilayer structure non-intrusively. Internal cracks of the material were detected by this technique.

A theory for optoacoustic signal generation, propagation and detection is given. A numerical analysis technique is developed to solve for the expected signal. In …

Ellipsometric Determination Of Optical Constants For Silicon And Thermally Grown Silicon Dioxide Via A Multi-Sample, Multi-Wavelength, Multi-Angle Investigation, C. M. Herzinger, B. Johs, W. A. Mcgahan, John A. Woollam, W. Paulson

Department of Electrical and Computer Engineering: Faculty Publications

Optical constant spectra for silicon and thermally grown silicon dioxide have been simultaneously determined using variable angle of incidence spectroscopic ellipsometry from 0.75 to 6.5 eV. Spectroscopic ellipsometric data sets acquired at multiple angles of incidence from seven samples with oxide thicknesses from 2 to 350 nm were analyzed using a self-contained multi-sample technique to obtain Kramers–Kronig consistent optical constant spectra. The investigation used a systematic approach utilizing optical models of increasing complexity in order to investigate the need for fitting the thermal SiO₂ optical constants and including an interface layer between the silicon and SiO₂ in modeling …

Performance Of Imaging Laser Radar In Rain And Fog, Kathleen M. Campbell

Theses and Dissertations

The Air Force is currently developing imaging laser radar systems (ladar) for use on precision guided munitions and other imaging systems. Scientists at Eglin Air Force Base, in conjunction with Wright Laboratories, are testing a 1.06-um wavelength ladar system and need to understand the weather effects on the ladar images. As the laser beam propagates through the atmosphere, fog droplets and raindrops can cause image degradation, and these image degradations are manifested as either dropouts or false returns. An analysis of the dropouts and false returns helped to quantify the performance of the system in adverse weather conditions. Statistical analysis …

Joint Wavelet Transform Correlation With Separated Target And Reference Planes, Boon Yi Soon, Mohammad A. Karim, Russell C. Hardie, Mohammad S. Alam

Electrical and Computer Engineering Faculty Publications

In recent years, we realize the usefulness of feature extraction for optical correlator and hereby, we investigate the capability of Laplace operator in feature extraction of multiple targets. The first-order terms and the false alarm terms in the correlation output would be removed using electronic power spectrum subtraction technique. Most importantly, the entire magneto-optic SLM is completely utilized for displaying only targets in the input scene. A new cost efficient hardware implementation is proposed and aforementioned result of the proposed system is evaluated through computer simulation.

Field Solutions For Bidirectional High-Gain Laser Amplifiers And Oscillators, Lee W. Casperson, Mohammad Azadeh

Electrical and Computer Engineering Faculty Publications and Presentations

General analytical solutions are obtained for the amplitude, phase, and intensity of the electromagnetic waves in bidirectional homogeneously broadened high-gain laser amplifiers and oscillators. These solutions are important as increasingly high-gain lasers are being employed in practical systems. Expressions are derived relating the output power to the input, including the effects of arbitrary mirror reflectivities and frequency detunings from the line center. For negligible reflectivities, these regenerative amplifier results reduce to earlier expressions for single-pass high-gain amplifiers. Multivalued outputs also occur, and in the limit of low gain per pass the results are consistent with earlier studies of single-frequency laser …

Studies Of Metallic Multilayer Structures, Optical Properties, And Oxidation Using In Situ Spectroscopic Ellipsometry, Xiang Gao, Jeff Hale, Scott Heckens, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

In situ spectroscopic ellipsometry (SE) has been successfully used to accurately measure sputter deposition rates and optical constants of un-oxidized metal layers and to control the growth of magnetic multilayers. The structures include [Co/Cu] _n , [Co/Au] _n , [Co/Ni] _n , [Co/Pd] _n and [Co/Pd/ Au] _n . Layer thickness precision is better than ±0.05 nm for layer thicknesses in the range of 0.2 nm to 10 nm. Closed-loop feedback control of layer thickness is also demonstrated. Good consistency was obtained by comparing the in situ SE results to x-ray diffraction measurements. Dynamic oxidation studies of [Co/Au] _n and …

Linear Reconstruction Of Non-Stationary Image Ensembles Incorporating Blur And Noise Models, Stephen D. Ford

Theses and Dissertations

Two new linear reconstruction techniques are developed to improve the resolution of images collected by ground-based telescopes imaging through atmospheric turbulence. The classical approach involves the application of constrained least squares (CLS) to the deconvolution from wavefront sensing (DWFS) technique. The new algorithm incorporates blur and noise models to select the appropriate regularization constant automatically. In all cases examined, the Newton-Raphson minimization converged to a solution in less than 10 iterations. The non-iterative Bayesian approach involves the development of a new vector Wiener filter which is optimal with respect to mean square error (MSE) for a non-stationary object class degraded …

Multiple Model Adaptive Estimation Using Filter Spawning, Kenneth A. Fisher

Theses and Dissertations

Multiple Model Adaptive Estimation with Filter Spawning is used to detect and estimate partial actuator failures on the VISTA F-16. The truth model is a full six-degree-of-freedom simulation provided by Calspan and General Dynamics. The design models are chosen as 13-state linearized models, including first order actuator models. Actuator failures are incorporated into the truth model and design model assuming a "failure to free stream . Filter Spawning is used to include additional filters with partial actuator failure hypotheses into the Multiple Model Adaptive Estimation (MMAE) bank. The spawned filters are based on varying degrees of partial failures (in terms …

Studies Of Surface Electrochemistry And Electrocatalysis At Atomic And Molecule Level, Shigang Sun

Journal of Electrochemistry

The main progresses achieved during last few years in our research group concerning studies of surface electrochemistry and electrocatalysis were reviewed in this present paper. Four topics were described: 1) the surface electrochemistry and model electrocatalysis of metal single crystal planes, 2) the electrocatalytic reaction mechanism and the control of reaction pathways at molecule level, 3) the reaction kinetics of electrooxidation of small organic molecules, and 4) the relationship between the properties and the surface chemical states of electrocatalyst. This review lays in emphasis on the demonstration of the results as well as the research direction of surface electrochemistry and …

A Preliminary Study On Thin Film Plasticizing Lithium Ion Battery, Quanfeng Dong, Hanxi Yang, Xinping Ai, Xiaohong Hu, Shengxian Li

Journal of Electrochemistry

A dry polymer electrolyte was made by plasticizing a copolymer matrix and further filling with liquid electrolyte. A thin-film lithium ion battery based on the dry polymer electrolyte was manufactured and its electrochemical properties were measured. It is found that the thin film lithium ion battery exhibits similar discharge properties to liquid electrolyte battery, and shows strong high rate capability.

Study On The Synthesis And Electrochemical Behavior Of Poly (Quinonoid-Disulfide), Xiaohui Tang, Xiuwu Sun, Yongfang Li, Shibi Fang

Journal of Electrochemistry

Organic polydisulfide containing quinonoid structure was synthesized by chloromethylation, oxidation by nitric acid, and condensation polymerization with sodium disulfide. The effect of quinonoid structure on the electrochemical behavior of organic polydisulfide was investigated with cyclic voltammetry and chargedischarge measurement. The result shows that quinonoid struture mainly affects the positions of redox peaks of organic polydisulfide, open circuit voltage and discharge platform voltage of cell with the organic polydisulfide as cathode.

The Investigations Of Surface Treatment Methods And Characterization Of Oxide Films On Ab5 Based Metal Hydride Electrodes Ⅰ. New NiRich Treatment Methods And Photoelectrochemical Characterization Of Oxide Films, Junmin Nan, Yong Yang, Jun Li, Zugeng Lin

Journal of Electrochemistry

Two simple and efficient surface treatment methods for AB₅ type hydrogen storage alloys were developed. The results of X-ray photoelectron spectroscopy (XPS) and cyclic voltammetric (CV) experiments showed that the hydrogen storage alloys treated by two different methods had Ni rich surface layer so that the performances of the electrodes were improved after treatment. The characterization of the oxide films which formed on the surface of electrodes through potentiodynamic oxidation with the help of photoelectrochemical microscopy (PEM) were done. The anodic photocurrent and the cathodic photocurrent related to the oxidation of hydrogen and the reduction of oxygen on the …

A Study On Heterogeneous Indirect Electrosynthesis Of Benzaldehyde, Daobao Chu, Changjian Lin, Huashui Lin, Jianguang Tan

Journal of Electrochemistry

Heterogeneous indirect electrosynthesis process of benzaldehyde has been investigated using cyclic voltammetry and polarization curves. An optimum condition for preparation of benzaldehyde by indirect electrooxidation of toluenc with redox Mn³⁺/Mn²⁺ is given in this paper. Electrolytic regeneration Mn³⁺ are made at Pt/Ti anode in “slurry” MnSO₄/H₂SO₄ medium. Current efficiency for electrolytic regeneration Mn³⁺  was maintained over 88% by “double cyclic way”.

Investigation Of Methanol Anode Electrooxidation Catalysts, Gangyao Wen, Ying Zhang, Zhenglong Yang, Changzhi Li

Journal of Electrochemistry

A series of catalysts, Pt-WO₃/C, Pt/Ru/C and Pt-Ru-WO₃/C were prepared by chemical reduction deposition. Electrocatalytic oxidation of methanolon different catalyst/Nafion membrane electrodes was studies by voltammetry and current-potential polarization. The results indicated that the catalytic activity order of different catalysts is as follows: Pt-Ru-WO₃/C > Pt-Ru/C > Pt-WO₃/C. At the same time, influences of methanol concentrations and catalyst proportion on performances of anodes were also studies.

Progresses In Surface Electrochemistry And Electrocatalysis ——A Review On The 1997 Joint International Meeting Of Electrochemistry And 97' International Meeting Of Surface Electrochemistry, Shigang Sun

Journal of Electrochemistry

The progresses in surface electrochemistry and electrocatalsis reported in the 1997 joint international meeting of electrochemistry and in the 97′ international meeting of surface electrochemistry were reviewed. The main trends described in this paper consisted of 7 aspects: 1) the studies employing single crystal electrodes, 2) the development of in situ methods of diverse spectroscpoy, 3) the innovation of new research techniques, 4) the preparaton of electrocatalyst of high performances, 5) the quantitative studies on kinetics of electrocatalytic reactions, 6) the investigation on the dynamic processes of surface by timeresolved methods, and 7) the theoretical modeling and simulation of surface …

Anchor Effect Of Iron And Cobalt To Platinum On Carbon Substrates, Zidong Wei, Hetong Guo, Zhiyuan Tan

Journal of Electrochemistry

The cathodic reduction of oxygen is studied on porous carbonbased electrodes carrying platinumiron and/or cobalt alloy catalysts. Electrodes using such electrocatalysts, particularly when used as cathodes in acidic electrolytes, remain stable for longer periods. The cathodic polarization of oxygen reduction on such electrodes is 20 mV to 40 mV lower than that on the conventional electrode on which only platinum alone is used as an electrocatalysts. An accelerated aging test (AAT) is used to evaluate the corrosion resistance and sintering resistance of each catalyst. The dissolution of the catalyst in the AAT filtrate is analysed and provides a measure of …

Study On Nano Electrode Material Of Lithium Ion Batteries, Jinkua You, Yong Yang, Dong Shu, Shenghui Wu, Yingchun Zhang, Zugeng Lin

Journal of Electrochemistry

In this paper, the structure and morphology of the nano phase electrode materials have been characterized with XRD and TEM. The performances of electrochemical intercalation and deintercalation of lithium ions have been studied by using cyclic voltammograms and galvanostatic charge discharge techniques. The results show that the nano materials posses advantage of micro structure and Li⁺ ions intercalation performances. The observed high capacity and large charge discharge current density of the nano phase materials seem to have resulted from three kinds of effects: 1) an increase in the space for Li⁺ ions intercalation; 2) a decrease in the …

Neural Network Based Optimizing Controllers For Smart Structural Systems, Rajendra Damle, Vittal S. Rao

Electrical and Computer Engineering Faculty Research & Creative Works

Neural network-based controllers for vibration suppression of smart structural systems have been reported in several recent studies. These studies have shown that in addition to conventional controller design methodologies, neural networks offer an effective basis for design and implementation of controllers. With the introduction of neural network chips like the electronically trainable analog neural network (ETANN) chip i80170NX by Intel and the Ni1000 chip by Nestor Corp., stand-alone hardware implementation of neural network-based controllers is possible. In this paper the capabilities of Intel's ETANN chip to implement linear and nonlinear controllers for smart structural systems have been investigated. A neural …