Digital Commons Network^™

On Chip Implement Of Deadlock Avoidance In Wormhole Networks, Kiran K. Gururaj

Theses

This thesis gives a detailed description of the Application Specific Integrated Circuit (ASIC) design to avoid deadlocks in Wormhole Networks. Deadlock avoidance is the most critical issue while considering wormhole networks and should be avoided by any routing protocol and algorithm. A novel architecture for the Turn Prohibition Based Routing (TPBR) protocol has been proved to be efficient and was developed as a part of this work. This architecture for implementing the algorithm is divided into three parts. The first part determines the order of selccuon of the nodes, in the network to run the algorithm. The second part deals …

Optimum Of Catalyst Layers For Direct Methanol Fuel Cells, Jun Zhang, Lei Li, Li Xu, Yu-Xin Wang

Journal of Electrochemistry

The performances of membrane electrode assemblies (MEAs)with various Pt loading were compared. The amount of Nafion in a catalytic layer was optimized, and the effect of Nafion loading on the resistance of MEAs was investigated with ac impedance spectroscopy. For a MEA with both Pt 4 mg/cm² in the anode and the cathode, suitable Nafion loading was 21.4 wt% in the anode. With 21.4 wt% Nafion loading in the cathode, the Direct Methanol Fuel Cells(DMFC) showed the highest performance at high current density. While, the DMFC performances came down, as Nafion loading increasing,for ohm and concentration polarization.

Study On Modification Of Spinel Limn2O4 By Overcoating, Ren-Gang Zhang, Shi-Xi Zhao, Jung-Lei Xia, Han-Xing Liu

Journal of Electrochemistry

The surface of spinel LiMn₂O₄ was modified by the sol-gel process with LiCoO₂-coated LiMn₂O₄ and studied by XRD, SEM and EPMA. The results have shown that the surface of the coated grains heated at 700 ℃ for 10h, which is cubic spinel, were Co-rich. The amount of Co³⁺ in the grains changed owing to different place of the grain and decreased from surface to inner parts. Using the coated as the cathode of Li-ion cells, the initial capacity deceased slightly, but the amount of Mn²⁺ solving in electrolyte decreased, Jahn-Teller …

Ionic Conduction In Ba0.95Ce0.9Y0.1O3 - Α Solid Oxide And Its Performance In Fuel Cell, Gui-Lin Ma, Ding-Xian Jia, Li-Gan Qiu, Hui Shi, Rong Chen

Journal of Electrochemistry

Using Ba_0.95Ce_0.9Y_0.1O_3-α as a solid electrolyte and porous platinum as electrodes,hydrogen and oxygen concentration cells and hydrogen-air fuel cell were constructed, respectively. Electromotive forces (MEFs) of the gas concentration cells and I-V characteristics of the fuel cell were detdrmined in the temperature range of 600～1 000 ℃. The Ba_0.95Ce_0.9Y_0.1O_3-α exhibited almost the pure protonic conduction under hydrogen gas,and a mixed conduction of oxide-ion and electron hole with oxide-ion transport number of 0.3～0.5 under oxygen gas. It exhibited a mixed conduction of proton and oxide-ion with the …

Modification Of Molybdenum Nitride Electrode For Supercapacitor(I)——The Effect Of Ammonium Vanadate On The Properties Of Molybdenum Nitride Electrode, Xue-Liang Li, Dao-Rong Luo, Hua-Lin Wang, Jian-Bo He, Yun-Guei Zhu

Journal of Electrochemistry

The effect of vanadium on the properties of the electrode of molybdenum nitride has been studied by using XRD, SEM and cyclic voltammetry. Modified molybdenum nitride was made as follow: films were coated by dipping titanium sheet in the solution containing different composition of molybdenum oxide, ammonium vanadate, ammonia, glycol and oxalic acid, and coated films are reacted with free ammonia. The results show that the specific capacitance of modified electrode was considerably increased and the operation voltage was broadened with the addition of ammonium vanadate in the dipping solution. The mechanism of these effects generated is the formation of …

Some Consideration For Lithium-Ion Cells' Safety, Guang-Xia Hu, Jing-Ying Xie

Journal of Electrochemistry

The safety is the most important problem for lithium ion cells, especially for large lithium ion cells. In this paper, some information about lithium ion cells' safety can be learned by discussing several aspects of lithium ion cells, such as, materials of lithium ion cell, manufacturing processes, using conditions and so on.

Synthesis And Characterization Of Lini0.8-XAlXCo0.2O2 As Cathodes For Lithium-Ion Batteries, Jun Zhang, Zhong-Kao Jin, Qing-He Yang, Qing-Mei Song, Xiao-Hua Ma, Xiang-Fu Zong

Journal of Electrochemistry

Single-phase solid solution of LiNi_0.8-xAl_xCo_0.2O₂ (0≤ x <0.1)had been synthesized and characterized by X-ray diffraction(XRD) and scanning electron microscopy (SEM). Their electrochemical performance was examined by charge-discharge cycling. The LiNi_0.71Al_0.09Co_0.2O₂ compound showed a discharge capacity of 152 mAh/g after 20 cycles that corresponds to 97.4% capacity retention. The beneficial effect of co-doping with Al and Co elements was corro-borated by slow scanning cyclic voltammograms(SSCV), electrochemical impedance spectrum (EIS) and differential scanning calorimetry (DSC) data on charged cathodes. These results show that the 2D-character of the crystal lattice was stabilized by co-doping with Al and Co, the phase transitions that occur during deintercalation or intercalation of Li-ions were significantly suppressed, …

Research Progress On Electrode Material In All-Vanadium Redox Battery, Hua Li, Shou-Wen Chang, Chuan-Wei Yan

Journal of Electrochemistry

An all-vanadium redox flow storage battery possesses many advantages over conventional storage batteries.The development statue of two types electrode materials (metal and compound type) is introduced in this article.

Initial Stages Of Copper Electrodeposition On Glassy Carbon Electrode, Ling Huang, Rui Zhang, Min Gu, Fang-Zu Yang, Shu-Kai Xu, Shao-Min Zhou

Journal of Electrochemistry

Initial stages of copper electrodeposition on glassy carbon electrode from acid sulphate solutions were studied using cyclic voltammetry and chronoamperometry. The electrolyte solution was a 0.05 mol.L^-1 copper sulphate, 1.4～1.8 mol⋅L^-1 sulphuric acid containing 1 mg·L^-1 2-mercaptobenzoimidazole, Results show that 2-mercaptobenzoimidazole produced an inhibition of the copper deposition, probably related to the adsorption,sulphuric acid promote copper electrodeposition. The initial deposition kinetics corresponded to a model including instantaneous nucleation and diffusion controlled growth.Addition of 2-mercaptobenzoimidazole and sulphuric acid did not change the initial nucleation of copper electrocrystallization, it increased the nucleation rate and the number density of nuclei …

Linear Feature Detection Using Multiresolution Wavelet Filters, Samuel Peter Kozaitis, Somkait Udomhunsakul, Rufus H. Cofer, A. Agarawal, Shuwu Song

Electrical Engineering and Computer Science Faculty Publications

We detected roads in aerial imagery based on multiresolution linear feature detection. Our method used the products of wavelet coefficients at several scales to identify and locate linear features. After detecting possible road pixels, we used a shortest-path algorithm to identify roads. The multiresolution approach effectively increased the size of the region we examined when looking for possible road pixels and reduced the effect of noise. We found that our approach leads to an effective method for detecting roads in aerial imagery.

Sum Normal Optimization Of Fuzzy Membership Functions, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

Given a fuzzy logic system, how can we determine the membership functions that will result in the best performance? If we constrain the membership functions to a certain shape (e.g., triangles or trapezoids) then each membership function can be parameterized by a small number of variables and the membership optimization problem can be reduced to a parameter optimization problem. This is the approach that is typically taken, but it results in membership functions that are not (in general) sum normal. That is, the resulting membership function values do not add up to one at each point in the domain. This …

Temporal Modeling Of Software Test Coverage, Sahra Sedigh, Arif Ghafoor, Raymond A. Paul

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents a temporal model for the coverage achieved by software testing. The proposed model, which is applicable at any level of the testing hierarchy, can determine the value of test coverage at any given time, as well as predicting future values. The model is comprised of two main components: coverage functions, and the coverage matrix. The coverage functions represent the coverage of a single entity as a function of time and reflect the test environment through their stochastic parameters. The coverage matrix utilizes the coverage functions to depict the coverage attained for each entity by each test within …

Quality Enhancement Of Reconfigurable Multichip Module Systems By Redundancy Utilization, Minsu Choi, Nohpill Park, Fabrizio Lombardi, Vincenzo Piuri

Electrical and Computer Engineering Faculty Research & Creative Works

This paper evaluates the quality effectiveness of redundancy utilization in reconfigurable multichip mode (RMCM) systems. Due to reconfigurability, the RMCM system can implement a device with different redundancy levels. A redundancy level is determined by the requirement of fault tolerance (FT) of the device under implementation which can be realized through reconfiguration. No previous work has adequately investigated the effect of utilization of redundancy on the quality-level (QL) of RMCM. In this paper, the tolerance to escape from testing is also introduced to provide more extensive and comprehensive analysis and is referred to as escape tolerance (ET). This can be …

Application Of Higher-Order Fem Elements To The Analysis Of Microstrip Structures, H. Wang, C. L. Guo, Todd H. Hubing, James L. Drewniak, Thomas Van Doren, Richard E. Dubroff

Electrical and Computer Engineering Faculty Research & Creative Works

Microstrip structures, formed by metal traces printed on a dielectric substrate above a reference plane, are frequently the object of electromagnetic modeling. In this paper, hybrid FEM/MoM formulations employing conventional Whitney elements and newly developed linear-tangent/linear-normal (LT/LN) tangential vector finite elements (TVFEs) are applied to the analysis of microstrip structures with thin traces. This paper shows that the variation of the electric field below the trace is a significant issue to be addressed in microstrip structure modeling. Different mesh methods are investigated and the advantages of the LT/LN TVFEs are discussed.

Experimental Demonstration Of Multiple Robot Cooperative Target Intercept, Timothy W. Mclain, Randal W. Beard, Jed M. Kelsey

Faculty Publications

This paper presents experimental results for the simultaneous intercept of preassigned targets by a team of mobile robots. The robots are programmed to mimic the dynamic behavior of unmanned air vehicles in constant-altitude flight. In proceeding to their targets, robots must avoid both known static threats and pop-up threats. An overview of the cooperative control strategy followed is given, as well as a description of the robot hardware and software used. Experimental results demonstrating simultaneous intercept of targets by the robot team are presented.

Development Of An Efficient Ti:Sapphire Laser Transmitter For Atmospheric Ozone Lidar Measurements, Khaled A. Elsayed

Electrical & Computer Engineering Theses & Dissertations

The impetus of this work was to develop an all solid-state Ti:sapphire laser transmitter to replace the current dye lasers that could provide a potentially compact, robust, and highly reliable laser transmitter for differential absorption lidar measurements of atmospheric ozone. Two compact, high-energy pulsed, and injection-seeded Ti:sapphire lasers operating at a pulse repetition frequency of 30 Hz and wavelengths of 867 nm and 900 nm, with M² of 1.3, have been experimentally demonstrated and compared to model results. The Ti:sapphire lasers have shown the required output beam quality at maximum output pulse energy, 115 mJ at 867 nm and …

Analysis Of Error Recovery Effects On Digital Flight Control Systems, Arturo Tejada Ruiz

Electrical & Computer Engineering Theses & Dissertations

Life-critical, real-time applications like flight-by-wire aircraft, rely on closed-loop digital control systems and fault-tolerant computer systems to reliably achieve the desired operation. The computer systems, however, may be affected by random hardware/software faults induced mainly by environmental conditions such as high intensity radiated fields (HIRF) and lightning. These harsh electromagnetic environments are known to induce common­ mode faults (CMF) in aircraft electronic systems, which disrupt fault-tolerant provisions and possibly affect the operation of the digital control system. Current flight-by-wire aircraft have computer systems that can neither detect CMF nor recover from them. New systems are under investigation that can recover …

Reflection-High Energy Electron Diffraction Study Of Si(100) Homoepitaxy By Femtosecond Pulsed Laser Deposition, Mohammed S. Hegazy

Electrical & Computer Engineering Theses & Dissertations

The dynamics of femtosecond pulsed laser deposition (fsPLD) of Si(!00)-1 x I and Si(!00)-2x I homoepitaxy are studied by in situ reflection high-energy electron diffraction (RHEED) and ex situ atomic force microscopy (AFM). The effects of substrate temperature, laser fluence and the pressure of a passive gas on the Si(!00)-1 x I growth mode are discussed. It is shown that films grow following the Volmer-Weber (3D) growth mode. The substrate temperature largely affects the morphology of the grown film. Below ~ 400 °C (at laser fluence of~ 1.9 J/cm²), randomly oriented 3D clusters are grown. This is shown …

A Comparative Application Of Telecommunication Traffic Forecasting Methods To A Backbone Link In Tanzania, M. L. Luhanga

Tanzania Journal of Engineering and Technology (TJET)

In this paper various mathematical models to characterize and forecast telecommunication traffic time series traffic have been applied, and the ranges of validity of the models are determined by comparing them with measured traffic data using the measurement errors criteria method which resulted into the superior model. Based on this model the ARIMA (0,2,1) model for smoothed data, the traffic forecast findings show that by the year 2006, the traffic demand will exceed the current installed capacity of 140 Mbps in the Tanzania Telecommunications Company Limited (TTCL) network along the major link between the Dar es Salaam and Dodoma backbone …

Probabilistic Microcell Prediction Model, Song-Kyoo Kim

Electrical Engineering and Computer Science Faculty Publications

A microcell is a cell with 1-km or less radius which is suitable for heavily urbanized area such as a metropolitan city. This paper deals with the microcell prediction model of propagation loss which uses probabilistic techniques. The RSL (Receive Signal Level) is the factor which can evaluate the performance of a microcell and the LOS (Line-Of-Sight) component and the blockage loss directly effect on the RSL. We are combining the probabilistic method to get these performance factors. The mathematical methods include the CLT (Central Limit Theorem) and the SPC (Statistical Process Control) to get the parameters of the distribution. …

Autoassociative-Heteroassociative Neural Network, Claudia V. Kropas-Hughes, Steven K. Rogers, Mark E. Oxley, Matthew Kabrisky

AFIT Patents

An efficient neural network computing technique capable of synthesizing two sets of output signal data from a single input signal data set. The method and device of the invention involves a unique integration of autoassociative and heteroassociative neural network mappings, the autoassociative neural network mapping enabling a quality metric for assessing the generalization or prediction accuracy of the heteroassociative neural network mapping.

A Course Assessment Of The Microelectronics Process Engineering Program At Sjsu, Gregory Young, Stacy H. Gleixner, David W. Parent, Yasser Dessouky, Emily Allen, Linda Vanasupa

Faculty Publications

The program assessment strategy of San Jose State University's new interdisciplinary curriculum in Microelectronics Process Engineering is described. Vertical integration of specific class and program learning objectives allows for a clear and efficient method to evaluate the continued growth and improvement of the program. The program assessment process relies on clearly defined and detailed program and course learning objectives that are linked vertically to ABET outcomes. In addition, we discuss briefly the structure of the program and the "hands-on" experience that we provide the students.

Logic Synthesis Of Reversible Wave Cascades, Alan Mishchenko, Marek Perkowski

Electrical and Computer Engineering Faculty Publications and Presentations

A circuit is reversible if it maps each input vector into a unique output vector, and vice versa. Reversible circuits lead to power-efficient CMOS implementations. Reversible logic synthesis may be applicable to optical and quantum computing. Minimizing garbage bits is the main challenge in reversible logic synthesis. This paper introduces an algorithm to generate the cascade of reversible complex Maitra terms (called here reversible wave cascade) implementing incompletely specified Boolean functions. The remarkable property of the presented method compared to other reversible synthesis methods is that it creates at most one constant input and no additional garbage outputs. Preliminary estimation …

Airborne Radar Interference Suppression Using Adaptive Three-Dimensional Techniques, Todd B. Hale

Theses and Dissertations

This research advances adaptive interference suppression techniques for airborne radar, addressing the problem of target detection within severe interference environments characterized by high ground clutter levels, levels, noise jammer infiltration, and strong discrete interferers. Two-dimensional (2D) Space-Time Adaptive Processing (STAP) concepts are extended into three-dimensions (3D) by casting each major 2D STAP research area into a 3D framework. The work first develops an appropriate 3D data model with provisions for range ambiguous clutter returns. Adaptive 3D development begins with two factored approaches, 3D Factored Time-Space (3D-FTS) and Elevation-Joint Domain Localized (Elev-JDL). The 3D adaptive development continues with optimal techniques, i.e., …

Validation Of Sea Ice Motion From Quikscat With Those From Ssm/I And Buoy, David G. Long, Yunhe Zhao, Antony K. Liu

Faculty Publications

Arctic sea ice motion for the period from October 1999 to March 2000 derived from QuikSCAT and ocean buoy observations. Special Sensor Microwave/Imager (SSM/I) data using the wavelet analysis method agrees well with ocean buoy observations. Results from QuikSCAT and SSM/I are compatible when compared with buoy observations and complement each other. Sea ice drift merged from daily results from QuikSCAT, SSM/I, and buoy data gives more complete coverage of sea ice motion. Based on observations of six months of sea ice motion maps, the sea ice motion maps in the Arctic derived from QuikSCAT data appear to have smoother …

Dynamic Multiphysics Model For Solar Array, Shengyi Liu, Roger A. Dougal

Faculty Publications

An approach to model the solar cell system with coupled multiphysics equations (photovoltaic, electro-thermal, direct heating and cooling processes) within the context of the resistive-companion method in the Virtual Test Bed computational environment is presented. Appropriate across and through variables are defined for the thermal terminal of the system so that temperature is properly represented as a state variable, rather than as a parameter of the system. This allows enforcement of the system power conservation through all terminals, and allows simultaneous solutions for both the electrical potentials and the system temperature. The thermal port built accordingly can be used for …

Closed Loop Identification Of A First Order Plus Dead Time Process Model Under Pi Control, Tony Kealy, Aidan O'Dwyer

Conference papers

Abstract -- This paper discusses the estimation of the parameters of a first order plus dead-time process model using the closed-loop step response data of the process under proportional plus integral (PI) control. The proportional gain and the integral time, in the PI controller, are chosen such that the closed-loop step response exhibits an under-damped response. From this response data, five characteristic points are used to determine a second order plus dead-time model and subsequently, the frequency response of the closed-loop system. Knowing the dynamics of the closed-loop system and the dynamics of the controller, the open-loop dynamics of the …

Adaptive Predictive Congestion Control Of High-Speed Atm Networks, Sarangapani Jagannathan, Jayasree Talluri

Electrical and Computer Engineering Faculty Research & Creative Works

This paper proposes an auto regressive moving average (ARMAX)-based adaptive control methodology to prevent congestion in high-speed asynchronous transfer mode (ATM) networks. Adaptive controller is developed to control traffic where sources adjust their transmission rates in response to the feedback information from the network switches. Specifically, the buffer dynamics at a given switch is modeled as a nonlinear discrete-time system and an ARMAX controller is designed so as to predict the explicit values of the transmission rates of the sources so as to prevent congestion. Tuning methods are provided for the unknown coefficients of the ARMAX model to estimate the …

Cuin1-Xalxse2 Thin Films And Solar Cells, P. D. Paulson, M. W. Haimbodi, S. Marsillac, R. W. Birkmire, W. N. Shafarman

Electrical & Computer Engineering Faculty Publications

CuIn[sub 1-x]Al[sub x]Se[sub 2] thin films are investigated for their application as the absorber layer material for high efficiency solar cells. Single-phase CuIn[sub 1-x]Al[sub x]Se[sub 2] films were deposited by four source elemental evaporation with a composition range of 0≤x≤0.6. All these films demonstrate a normalized subband gap transmission >85% with 2 µm film thickness. Band gaps obtained from spectroscopic ellipsometry show an increase with the Al content in the CuIn[sub 1-x]Al[sub x]Se[sub 2] film with a bowing parameter of 0.62. The structural properties investigated using x-ray diffraction measurements show a decrease in lattice spacing as the Al content increases. …

Experimental Studies Of Wave Propagation In Three-Dimensional Photonic Crystals, John M. Tobias

Dissertations

Photonic crystals were proposed fifteen years ago. Propagation is selectively prevented through these crystals resulting in a photonic band gap, that is, a frequency region where light cannot propagate. These frequency bands are analogous to electronic band gaps in solid-state crystals.

The optical properties of the photonic crystal in regions near the band gap remain relatively unexplored. Yet, there is significant evidence to suggest that this avenue of investigation can provide useful optical and microwave applications. Numerical studies have predicted that the effective permittivity near the photonic band gap approaches zero and becomes negative. Selfcollimation of the propagating beam and …