Digital Commons Network^™

A Multiplier-Less Architecture For High Speed Computation Of Multi-Dimensional Convolution, Ming Zhu Zhang

Electrical & Computer Engineering Theses & Dissertations

One of the most computationally intensive operations in digital image/video processing systems is multi-dimensional convolution. Every image/video processor needs the convolution module in its pre-processing stage. Fast and efficient design of the convolution module in an application specific system is a great challenge in VLSI (Very Large Scale Integration) design. Convolution operator requires a large set of multipliers and accumulators. A high precision multiplier takes enormous amount of VLSI area and it consumes more power. Hence reduction of the number of multipliers is another important challenge in VLSI design. A multiplier-less architecture for the design of a multi-dimensional convolution module …

Pulse Regulation Control Technique For Flyback Converter, Mehdi Ferdowsi, Ali Emadi, Mark Telefus, Curtis Davis

Electrical and Computer Engineering Faculty Research & Creative Works

Pulse regulation, a fixed frequency control technique, is introduced and applied to flyback converter operating in discontinuous conduction mode (DCM). The control parameters are designed in a way that the converter operates as close as possible to the critical conduction mode. In contrast to the conventional pulsewidth modulation control scheme, the principal idea of pulse regulation is to achieve output voltage regulation using high and low-power pulses. Pulse regulation is simple, cost effective, and enjoys a fast dynamic response. The proposed technique is applicable to any converter operating in DCM. However, this work mainly focuses on flyback topology. In this …

Modeling And Simulation Of Silicon Photonic Crystals Effect Of Oxidation And Etching, G. M. Haider Ali

Electrical & Computer Engineering Theses & Dissertations

Recent inventions of a silicon Raman laser and a high speed photon modulator might motivate integration of electronic and photonic active devices on the same silicon chip. Passive photonic devices in silicon such as waveguides, couplers and splitters have been developed. Photonic devices must be compatible with standard silicon CMOS fabrication processing in order to achieve the integration. Since CMOS fabrication involves a myriad of process steps, it is important to study the effect of processing on photonic devices. Oxidation and etching, two fundamental processes in silicon technology, are utilized in this thesis to model their effects on silicon photonic …

A Pam Decomposition Of Weak Cpm, Mason B. Wardle

Theses and Dissertations

The Enhanced Flight Termination System uses weak CPM as its modulation scheme and a limiter-discriminator as its demodulation scheme. A PAM representation of weak CPM was developed which representation provided the necessary componenents to build a simplified PAM-based receiver that outperformed the EFTS limiter-discriminator, even in the presence of phase noise. The PAM representation also provided a new perspective into the negative characteristics of weak CPM.

Predicting On-Orbit Seu Rates, Keith S. Morgan, Michael J. Wirthlin

Faculty Publications

As process geometry sizes continue to decrease, microelectronics are becoming more vulnerable to the effects of radiation. Of particular concern are the effects of Single-Event Upsets (SEU) in Field Programmable Gate Arrays (FPGA). An SEU causes a dynamic memory element, such as a flip-flop or latch, to unwantedly change state. Since FPGAs are becoming an increasingly attractive solution for space system electronics, it is desirable to predict static on-orbit SEU rates likely to be encountered by a particular device for any particular orbit. Mean Time Between Failure (MTBF) can directly be calculated from a static SEU rate, allowing a system …

The Hybrid Architecture Parallel Fast Fourier Transform (Hapfft), Joseph M. Palmer

Theses and Dissertations

The FFT is an efficient algorithm for computing the DFT. It drastically reduces the cost of implementing the DFT on digital computing systems. Nevertheless, the FFT is still computationally intensive, and continued technological advances of computers demand larger and faster implementations of this algorithm. Past attempts at producing high-performance, and small FFT implementations, have focused on custom hardware (ASICs and FPGAs). Ultimately, the most efficient have been single-chipped, streaming I/O, pipelined FFT architectures. These architectures increase computational concurrency through the use of hardware pipelining. Streaming I/O, pipelined FFT architectures are capable of accepting a single data sample every clock cycle. …

A Synchronous Primary-Side Dimming Controller For Cold-Cathode Fluorescent Lamp Ballast, Jenn-Jong Shieh

Journal of Marine Science and Technology–Taiwan

In this paper, a rectified quasi-sinusoidal pulse width modulation (RQSPWM) controller is first proposed for the cold-cathode fluorescent lamp (CCFL) ballast to achieve a synchronous primary-side dimming control. It is seen that, with the novel controller, not only the lamp flickering problem and the thermometer effect can be eliminated but also the useful photo-coupler in secondary side can be avoided to reduce cost. Then, small signal models of the CCFL ballast and the proposed RQSPWM dimming controller are derived to analyze the performance of the ballast system and help corroborate hardware loop measurements. Finally, a prototype is constructed for verifying …

System And Method For Differential Data Collection, Jack P. Glas, Vladimir I. Prodanov

Electrical Engineering

The present invention is directed towards a data detector for deriving a data signal from an incoming radio frequency input. The data detector comprises a delay logic which receives an unfiltered signal in quadrature and in-phase components, and applies a delay to each of the in-phase and quadrature phase components of the unfiltered input signal. The detector further comprises a first multiplication logic that multiplies the delayed in-phase component of the unfiltered signal by the quadrature phase component of the unfiltered signal to obtain a first result, and a second multiplication logic that multiplies the delayed quadrature phase component of …

Scene-Based Nonuniformity Correction Technique For Focal-Plane Arrays Using Readout Architecture, Balaji Narayanan, Russell C. Hardie, Robert A. Muse

Electrical and Computer Engineering Faculty Publications

Spatial fixed pattern noise is a common and major problem in modern infrared imagers due to the nonuniform response of the photodiodes in the focal plane array of the imaging system. In addition, the nonuniform response of the readout and the digitization electronics, involved in multiplexing the signals from the photodiodes, causes further nonuniformity. In this paper, we describe a novel scene based nonuniformity correction algorithm that treats the aggregate nonuniformity in separate stages. Firstly, the nonuniformity from the readout amplifiers is corrected using knowledge of the readout architecture of the imaging system. In the second stage, the nonuniformity resulting …

Segmentation Of Thermal Images For Non-Destructive Applications, Solange Yohali

Masters Theses

Infrared Thermogarphy (IR) is used in this project to detect subsurface conditions in concrete specimen for nondestructive testing and evaluations. This thesis goal is to bridge the gap between Infrared Testing and image analysis by developing an algorithm based on the region growing approach to segment the images and identify the voids without human interference or prior knowledge of the conditions. The segmentation algorithm starts with seed points as the hottest pixels in the image, and then regions are grown based on a neighborhood comparison criterion. The algorithm was tested on images collected from concrete specimen containing various man-made defects …

Effects Of Piconet Saturation On A Bluetooth Streaming Audio Channel, Theodore L. Josue

Theses and Dissertations

Bluetooth is a technology for wireless personal area networks (WPAN) that eliminates the need for cables, standardizes interfaces, and can automate many standard office processes such as sending and receiving email, synchronizing schedules, or exchanging business cards. With each workstation creating its own Bluetooth network, called a piconet, different Air Force environments have the potential, in some cases, to create more than 50 overlapping piconets, which significantly increases the potential for inter-piconet interference. This research investigates the effects of inter-piconet interference on a Bluetooth channel, streaming audio, offered at 24, 40, and 64 Kbps. It shows that as the number …

Disordered Speech Assessment Using Automatic Methods Based On Quantitative Measures, Lingyun Gu, John G. Harris, Rahul Shrivastav, Christine Sapienza

Electrical and Computer Engineering Faculty Research & Creative Works

Speech quality assessment methods are necessary for evaluating and documenting treatment outcomes of patients suffering from degraded speech due to Parkinson's disease, stroke, or other disease processes. Subjective methods of speech quality assessment are more accurate and more robust than objective methods but are time-consuming and costly. We propose a novel objective measure of speech quality assessment that builds on traditional speech processing techniques such as dynamic time warping (DTW) and the Itakura-Saito (IS) distortion measure. Initial results show that our objective measure correlates well with the more expensive subjective methods. © 2005 Hindawi Publishing Corporation.

Environmental-Based Characterization Of Soc-Based Instrumentation Systems For Stratified Testing, N. J. Park, Koshy M. George, Nohpill Park, Minsu Choi, Yong-Bin Kim, Fabrizio Lombardi

Electrical and Computer Engineering Faculty Research & Creative Works

This paper proposes a novel environmental-based method for evaluating the good yield rate (GYR) of systems-on-chip (SoC) during fabrication. Testing and yield evaluation at high confidence are two of the most critical issues for the success of SoC as a viable technology. The proposed method relies on different features of fabrication, which are quantified by the so-called Fabrication environmental parameters (EPs). EPs can be highly correlated to the yield, so they are analyzed using statistical methods to improve its accuracy and ultimately direct the test process to an efficient execution. The novel contributions of the proposed method are: 1) to …

Insulator Charging In Rf Mems Capacitive Switches, Jay F. Kucko

Theses and Dissertations

While capacitive radio frequency microelectromechanical (RF MEM) switches are poised to provide a low cost, high isolation, low power alternative to current RF switch technologies, there are still reliability issues limiting switch lifetime. Previous research identified insulator charging as a primary cause of switch failure. Changes in switch pull-in and release voltages were measured to provide insight into the mechanisms responsible for charging and switch failure. A spatial and temporal dependent model was developed to describe silicon nitride's time-dependent charging as a function of applied bias. This model was verified by applying constant biases to metal-silicon nitride-silicon capacitors and tracking …

Wide-Angle Multistatic Synthetic Aperture Radar: Focused Image Formation And Aliasing Artifact Mitigation, Jonathan E. Luminati

Theses and Dissertations

Traditional monostatic Synthetic Aperture Radar (SAR) platforms force the user to choose between two image types: larger, low resolution images or smaller, high resolution images. Switching to a Wide-Angle Multistatic Synthetic Aperture Radar (WAM-SAR) approach allows formation of large high-resolution images. Unfortunately, WAM-SAR suffers from two significant implementation problems. First, wavefront curvature effects, non-linear flight paths, and warped ground planes lead to image defocusing with traditional SAR processing methods. A new 3-D monostatic/bistatic image formation routine solves the defocusing problem, correcting for all relevant wide-angle effects. Inverse SAR (ISAR) imagery from a Radar Cross Section (RCS) chamber validates this approach. …

The Navigation Potential Of Signals Of Opportunity-Based Time Difference Of Arrival Measurements, Kenneth A. Fisher

Theses and Dissertations

This research introduces the concept of navigation potential, NP, to quantify the intrinsic ability to navigate using a given signal. NP theory is a new, information theory-like concept that provides a theoretical performance limit on estimating navigation parameters from a received signal that is modeled through a stochastic mapping of the transmitted signal and measurement noise. NP theory is applied to SOP-based TDOA systems in general as well as for the Gaussian case. Furthermore, the NP is found for a received signal consisting of the transmitted signal, multiple delayed and attenuated replicas of the transmitted signal, and measurement noise. Multipath-based …

Analysis And Characterization Of The Integrated Dielectric Slab Waveguide-Wedge Antenna Using Iterative Mode-Matching Technique, Chairat Pinthong

Dissertations

A rigorous solution for the TB and TM polarization to the dielectric wedge antenna fed by a slab waveguide of the same material is presented. The method of solution involves modeling the wedge as a sequence of step discontinuities and using an iterative procedure to track forward and backward partial wave fields, expressed as modal expansions, to obtain the rigorous field solution. Radiation patterns of directive gain are presented. All patterns smoothly decrease from a maximum in the endfire direction and exhibit very low side lobes. Longer length wedges are shown to produce higher directivity and smaller half-power beamwidths (HPBW). …

Difference-Expansion Based Reversible Data Hiding And Its Steganalysis, Guangsen Tian

Theses

A novel reversible data embedding method was reported in a recent IEEE journal article. The method was based on difference expansion (DE) technique. It used redundancy in digital images to achieve a high embedding capacity, while keeping visual distortion of the stego-image low. In this thesis, this technique was studied and experimentally evaluated. An effective steganalysis scheme for this DE-based reversible data embedding method was proposed, which used 12-dimensional feature vectors and a Bayes Classifier. The proposed steganalysis scheme steadily achieved a correct classification rate of 99%.

Stereo Vision Algorithm Using Propagation Of Correspondences Along An Array Of Cameras, Danyan Ganjali

Theses

One well known problem in stereo vision is the trade-off between precision and accuracy.

In a conventional two camera model, as the baseline separating the two cameras becomes smaller, the images that both cameras produce become more identical. This results in a more accurate set of correspondences, however at the same time causing less precise depth measurement due to the small angle used for triangulation. Similarly, in a larger baseline model, the depth measurement is more precise while the correspondences are not as accurate as of the shorter baseline model. This thesis proposes a method that promises to solve the …

Application Of Nickel Foam Electrode For Electroreduction Intermediate Of Purine, Hui-Wen Yang, Xi-En Hu, Xue-Jun Wang

Journal of Electrochemistry

Nickel foam with weight uniformity, good porosity ,pore size and low resistivity as a three-dimensional cathode was used in a filter-press electrochemical reactor. The H₂SO₄ as supporting electrolyte, separator of cation ion exchange membrane, and the lead plate as an anode were used. The cyclic system consisted of electroreduction reactor, pump, store tank and ampere meter. NAU was electroreduced in the cathode chamber of the reactor. Purine intermediate was synthesized with DAU, and the results were compared with those of iron powder reduction process. A peak current in the electroreduction process was detected. The current density of …

A Preliminary Study Of Electrocrystallization Of Bismuth On Glassy Carbon, Min-Li Yang, Zhan-Jun Zhang

Journal of Electrochemistry

The electrocrystallization of bismuth on glassy carbon electrodes (GCEs) from nitrate solutions was studied by cyclic voltammetry and chronoamperometry. Cyclic voltammograms exhibit a crossover between the cathodic and anodic branches, characteristic of the formation of bismuth nuclei on GCEs, and show that the bismuth electrocrystallization on GCEs is a diffusion-controlled reaction. The current transients were analyzed with the Scharifker and the Heerman equations. With the increaseof Bi³⁺ concentration, the non-dimensional plots leaned to the theoretical curve for 3D instantaneous nucleation and growth. The overpotential dependence of nucleation and growth mechanism was also found. With the increase of overpotential, the …

Preparation And Characterization Of Mcm-41/Pvdf-Hfp Composite Microporous Polymer Electrolytes For Li-Ion Batteries, Zuo-Feng Chen, Yan-Xia Jiang, Quan-Chao Zhuang, Quan-Feng Dong, Shi-Gang Sun

Journal of Electrochemistry

MCM-41/vinylidine fluoride-hexafluropropene copolymer (PVdF-HFP) composite microporous polymer electrolytes were prepared with mixed solvent of N, N-Dimethylformamide (DMF) and acetone. The influence of MCM-41 and nano-SiO₂ on the porous structure of the microporous polymer electrolytes were studied with SEM. The results show that MCM-41 could take the place of the plasticizer in the process of making pores, and bring the preparation of microporous membranes easily. The preliminary electrochemical tests showed that the ion conductivity of composite microporous polymer electrolyte with 10% MCM-41 was about 10^-3 S cm^-1, and the performance of batteries was improved. The mesoporous MCM-41selected …

Investigation On Ru-Ti-Ir-Sn Oxide Anode Coatings For Electrolyzing Seawater, Ke Wang, Yan Han, Lei-Yuan Wang, Xiao-Ling Zhang, Yu-Pu Sun

Journal of Electrochemistry

The anode coatings of Ru-Ti-Ir-Sn oxide with various compositions were prepared by thermal decomposition. The physical and electrochemical properties of the coatings were characterized by scanning electron microscope (SEM), energy dispersive X-ray detector (EDX), accelerated life, current efficiency, anti-Mn²⁺ contamination, polarization curveandcyclic voltammetry tests. The results showed thatthe anode coating with optimized formula possessed excellent overall properties for electrolyzing seawater.

Study On Synthesis Of M-Phenoxy Benzoic Acid By Electrolysis Oxidation Method, Wei Xu, Chong-Tao Zhao

Journal of Electrochemistry

The m-phenoxy benzoic acid was synthesized by oxidation m-phenoxy toluene using Cr(Ⅵ)as oxidation media, which was prepared by electrolysis oxidation of Cr(Ⅲ)in the electrochemical bath using Nafion 417 as a diaphragm, Pb-PbO₂ as an anode and Pb as cathode. The effect factors on the electrochemical oxidation of Cr(Ⅲ)to Cr(Ⅵ)in this electrolysis were studied. Furthermore, the optimal conditions for electronic synthesis of m-phenoxy benzoic acid were also discussed.

The Synthesis, Characteristics And Performance Of Cnt Composites As Anodic Materials In Litium-Ion Battery, Quan-Feng Dong, Ming-Sen Zheng, Zhen-Cai Huang, Ming-Gang Jin, Ya-Ding Zhan, Zu-Geng Lin

Journal of Electrochemistry

As an anodic material for lithium ion battery the carbon nano-tube (CNT) and some compounds based on tin have ever been investigated intensively. The fruited progress has not been made yet, however. In this paper the composites of CNT and Sn/SnO₂ were synthesized employing two methods and characterized by SEM and XRD. And the electrochemical performance of the composites was investigated.

The Effect Of Oxidant On Structure And Properties Of Pan/Ptfe Conducting Composite Membrane, Chang-Yuan Tao, Jing Chen, Jun Du, Cai-Xin Sun

Journal of Electrochemistry

The PAn/PTFE conducting composite membrane was prepared by means of in-situ permeating chemical polymerization, with (NH₄)₂S₂O₈ and Na₃VO₄ being used as an oxidant respectively. The polymerization-growth behavior of the aniline by using different oxidant was compared. In addition, the oxidant effect on the structure and properties of conducting composite membrane was discussed. The results of SEM micrographs, pore size distribution and electrochemical methods suggested that using either oxidants could also induce the product with small pore size and dense pore structure. Compared with (NH₄)₂S₂O …

The Preparation And Performance Of The Aqueous Matrix For Molten Carbonate Fuel Cells, Hua-Xin Lin, Mo-Jie Ceng, Bao-Lian Yi

Journal of Electrochemistry

PVA matrix of MCFC was prepared from the α-LiAlO₂ powder, and polyvinylalcohol(PVA), Compared with the conventional PVB matrix, higher porosity, higher thermal weight loss and smaller maximum pore diameter were achieved for PVA matrix. Single cell was assembled with PVA matrix. At reaction gas pressure of 0.9 MPa, under reaction gas utilization of 20%, at 300 and 428.57 mA·cm^-2, the cell voltage was 0.849 and 0.739 V respectively, and the output power density was 254.7 and 316.7 mW·cm^-2 respectively, which are higher than those of the cell assembled with PVB matrix. During thermal cycles, the cell …

Optical Characterization Of Porous Alumina From Vacuum Ultraviolet To Mid-Infrared, Daniel W. Thompson, Paul G. Snyder, Leon Castro, Li Yan, Prasuna Kaipa, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

Porous alumina was fabricated and optically characterized over a wide spectral range. Layers were formed electrochemically in oxalic acid solution from 10-μm-thick aluminum films evaporated onto silicon wafers. The layer formation was monitored with in situ spectroscopic ellipsometry in the visible and near-infrared wavelength range to accurately determine the thickness and dielectric functions. Anisotropy due to the columnar nature of the porous structure was determined using optical modeling. The porous alumina layer was found to have a small but significant absorption tail throughout the visible region. Atomic force microscopy and scanning electron microscopy were used throughout the process to assess …

Ac Impedance Measurement Techniques, Keith Corzine, M. Belkhayat, Yakov L. Familiant, Jing Huang

Electrical and Computer Engineering Faculty Research & Creative Works

Naval ship as well as aerospace power systems are incorporating a greater degree of power electronic switching sources and loads. Although these power electronics based components provide exceptional performance, they are prone to instability due to their high efficiency and constant power characteristics which lead to negative impedance. When designing these systems, integrators must consider the impedance versus frequency at a system interface (which designates source and load). Stability criterions have been developed in terms of source and load impedance for both dc and ac systems and it is often helpful to have techniques for impedance measurement. For dc systems, …

Wide-Band Lorentzian Media In The Fdtd Algorithm, Marina Koledintseva, James L. Drewniak, David Pommerenke, Giulio Antonini, Antonio Orlandi, Konstantin Rozanov

Electrical and Computer Engineering Faculty Research & Creative Works

This paper considers the case of a wide-band Lorentzian (WBL) algorithm in the finite-difference time-domain (FDTD) modeling of dispersive media. It is shown herein that the WBL model is a physically meaningful and practically useful case of the frequency behavior of materials along with the Debye and narrow-band Lorentzian (NBL). The recursive convolution algorithms for the finite-difference time-domain technique for NBL and WBL models differ. The Debye model, which is suitable for comparatively low-frequency dispersive materials, may not have sufficient number of parameters for describing the wide-band material, especially if this material exhibits pronounced absorption at higher frequencies. It is …