Digital Commons Network^™

Analysis And Development Of A Switched Capacitor Power Supply, John Richard Hackworth

Electrical & Computer Engineering Theses & Dissertations

The combination of a switched capacitor network and switching power supply techniques can result in a transformer less regulated DC power supply that is small, relatively simple, and efficient. In addition, the output of such a system could be operated over a wide range of common mode voltages. Multiple switched capacitor supplies could be stacked to achieve voltage multiplication.

Although the output of a system of this type is a continuous function, the internal operation must be analyzed in finite time elements. This numerical analysis will be shown in both a mathematical approach and a computer model.

Hydrogenation Effects On Trap Related Conduction In Diamond, Linwood Cleveland Watkins Iii

Electrical & Computer Engineering Theses & Dissertations

In this research work, the results of an experimental investigation on the electrical conduction mechanism in type Ιa and Ilb diamonds are presented. These results are compared with those of previous theoretical studies. The basic physical properties of diamond are discussed. Details of ohmic contact formation on diamond are presented.

The current-voltage characteristics revealed the presence of traps located below the Fermi level. The unfilled trap density was determined. The deep traps were further studied using spectroscopic photoconductivity measurements and the trap energy levels were determined.

The effects of hydrogenation on trap related conduction were studied subsequently. Hydrogenation was carried …

An Indirect Sensing Technique For Closed-Loop Diesel Fuel Quantity Control, Carl A. Maccarley, Walter D. Clark, Keay T. Nakae

Electrical Engineering

Despite significant advances in electronic control technology applied to diesel engines, commercially available injection systems for automotive diesel engines remain limited by the open-loop mapping of the injection pump. An initial calibration is relied upon to translate a fuel delivery command to an actual fuel quantity. In practice, however, these two variables may be substantially different due to the effects of mechanical wear, repair, and the wide range of operating conditions. Possible ramifications of this discrepancy are excessive exhaust smoke due to overfueling, increased fuel consumption, degraded driveability, and poor idle characteristics. The major obstacle to closing the fuel control …

Processing Of One-Fiber Interferometric Fiber-Optic Sensor Signals, A. Tino Alavie, Barry Grossman, Michael Thursby

Electrical Engineering and Computer Science Faculty Publications

Recent research conducted in the Fiber -Optic Sensor Systems Laboratory at Florida Institute of Technology in fiber -optic strain sensors for use in smart structures has concentrated primarily on one -fiber interferometers. Sensors using this technique are of particular interest because they are rugged and provide reasonable strain sensitivities, typically a thousand times that of microbend sensors, while requiring only a single optical fiber. As in two -fiber interferometers, some method must be used to convert the sensor signal output to an absolute strain value. One technique is to provide active phase tracking to keep the sensor signal output at …

Fiber-Optic Sensor And Smart Structures Research At Florida Institute Of Technology, Barry Grossman, Tino Alavie, Fred Ham, Jorge Franke, Michael Thursby

Electrical Engineering and Computer Science Faculty Publications

This paper discusses the fundamental issues being investigated by Florida Institute of Technology (F.I.T.) to implement the technology of smart structural systems for DoD, NASA, and commercial applications. Embedded sensors and actuators controlled by processors can provide a modification of the mechanical characteristics of composite structures to produce smart structures1-3. Recent advances in material science have spurred the development and use of composite materials in a wide range of applications from rotocraft blades and advanced tactical fighter aircraft to undersea and aerospace structures. Along with the advantages of an increased strength-to-weight ratio, the use of these materials has raised a …

Fault Tolerant Benes Networks, Manoj Bhatnagar

Theses

A fairly large number of fault tolerant topologies have been proposed for the multistage interconnection networks in the recent years. However very few of these schemes have focused on the Benes network. This thesis presents two new fault tolerant architectures for the Benes network. The thesis includes algorithms to construct these fault tolerant networks from a Benes network and the reconfiguration procedure in the event of a fault. The hardware characteristics of both the fault tolerant networks have been analyzed and compared.

Infrared Tv Camera With Ptsi Schottky-Barrier Detectors, Steven J. Blume

Theses

An infrared TV camera was developed for operating various sizes of Schottky-barrier IR-CCD image sensor chips. A digitally programmable frequency synthesizer is used so that the camera has the flexibility of using a 160 x 244 or 320 x 244 image sensor developed at the David Sarnoff Research Center. The outputs of the camera are compatible with an XYZ monitor, a standard TV monitor, and a computer workstation. Operation of the camera was demonstrated with a 160 x 244 image sensor producing an output on a standard TV monitor. Performance of the IR-TV camera system was investigated by evaluating CCD …

Performance Analysis Of A Dynamic Reservation Multichannel Local Area Network, Abubakar A. Ibrahim

Theses

A reservation multiaccess protocol. is proposed to be used on multichannel local area networks. This protocol is advantageous for networks supporting integrated services. The delay and throughput performance for message transmission are obtained by analysist The delay performance of the protocol is similar to the M-CSMA/CD/IC multichannel network proposed by Marsan and Roffinella. It is found that the reservation protocol can provide better throughput-delay characteristics when the fraction of the total available bandwidth allocated to data is increased. It is also observed that the maximum throughput increases with the increase in the number of channels when the total bandwidth is …

Formation And Characterization Of Thin Superconducting Y-Ba-Cu-O Films, Gyusuk Kim

Theses

Thin Y-Ba-Cu-O superconducting films were fabricated reproducibly on MgO (100) substrates by two different processes ; (1) deposition at a low substrate temperature fiom a single sintered YBa₂Cu_3.3O_x target using RF diode reactive sputtering followed by a post-annealing at around 830 ° C ; (2) deposition at the crystallization temperature under oxidizing atmosphere. The superconducting properties of films deposited by process (1) and (2) were studied. The variation of film composition and thickness as a function of distance from the target gas pressure and distance between target and substrate was studied. The Dependence of the …

Adaptive Fir Digital Filter Design And Simulation In The Noise Reduction System, Jack Jiabing Pang

Theses

The adaptive FIR digital filter is designed to suppress the noise in the tape recording and audio communication systems. The cutoff frequency of the digital FIR filters can be varied adaptively depending on the energy level of the input signal. In audio communication, especially, in tape recording systems, the noise obviously gets much bigger, when the frequency band of the system increases. The noise reduction system makes use of a phenomenon called masking, where the big signal-to-noise ratio makes human ears not sensitive to the noise. In a constant interval time, the system detects the signal level and compares the …

Sputter Deposition And Characterization Of High Tc Superconducting Thin Films, Vipulkumar Patel

Theses

Preparation of thin superconducting films by direct RF sputter deposition on Si, MgO, SrTiO₃ and quartz substrates and silver and Sl3N4 buffer layers (deposited on silicon substrates) was studied. To study resistance versus temperature characteristics of thin films and bulk materials, a computerized measurement system was developed. 1-1.5 pm thick YBaCuO films deposited on Si₃N₄/Si were found to be insulating with room temperature resistance higher than 236KΩ, while films with Ag as a buffer and/or a passivating layer exhibited metallic behavior with room temperature resistances lower than 700mΩ. The area directly under the 2.25 inches …

Simulation And Design Of Field Emission Diode, Yun Yuan

Theses

A new generation of microelectronic devices utilizing vacuum field emission cathodes becomes surging interest in recent years. This paper concentrates on the study of the field emission diode — a basic vacuum microelectronic device. The field emission efficiency, current spatial distribution and time dispersion of conical tips and wedges of various geometrical shapes are compared and calculated by analytical methods and computer simulations. Two field emitter heating effects, namely the Joule heating and Nottingham effect, are discussed theoretically. All the simulation results in this paper are performed on 386 based personal computer. The limiting memory space of PC induced simulation …

Uniformity Corrector And Signal Processing For A 160 X 244-Element Ir-Ccd Camera With Ptsi Schottky-Barrier Detectors, Paul D. Blume

Theses

An off-set-type, one point response uniformity corrector and the associated signal processing circuits was developed to be used for a 160 x 244-element IR-CCD camera with PtSi Schottky-barrier detectors. Image sensors with PtSi Schottky-barrier detectors exhibit two types of noise in the displayed video output, a temporal noise and a spatial fixed pattern noise. The performance of the image sensor, limited by the spatial noise which obscures low contrast detail and limits camera sensitivity, can be improved by a uniformity corrector. The uniformity corrector was constructed to substantially reduce the spatial noise in the output display by digitally subtracting a …

The Magnetotransport Analysis Of Hemt Structures At Low Fields, Naghmeh Nouri

Theses

On the basis of a study on numerous HEMT structures, a simple and useful technique was established for the characterization of 2DEG layers. This technique utilizes the magnetic field-dependence of the resistivity and Hall coefficient of the HEMT structure, to determine the values of the sheet density and mobility of 2DEG in the presence of other parallel conductive layers. This method of analysis was compared with previously used techniques such as Shubnikov-de Haas and the etch removal of the parallel conductive layers. Through this comparison and several measurements it was found that this procedure gives reproducible values for the 2DEG …

Image Preprocessing For Phase- Only Filtering, Samuel Peter Kozaitis, Atikom Roeksabutr

Electrical Engineering and Computer Science Faculty Publications

We compare the performance of an optical binary phase-only correlator using several nonlinear filters for preprocessing. An image of an airfield with different but similar appearing planes is used as the input data. The performance of the correlator was measured by examining several parameters in the correlation plane. Performance criteria are the signal-to-clutter ratio, the signal-to-noise ratio for objects within the same class, and the variance of the correlation peak within a class. Input images to the correlator were preprocessed using nonlinear filters based on both median filtering and adaptive filtering. The preprocessing improved the performance of the correlator by …

Major Project Management: The Yale Telecommunications Project

ACUTA: Other Publications

Back in the good old days, when the telephone business was simpler and Saturday night television was worth watching, I can remember Ted Knight the newsman (remember him on The Mary Tyler Moore Show?) looking off into some imagined horizon in the newsroom when asked how he happened to come to his current position. With head cocked upward and his hand clutching his right lapel, he'd start in his deepest, most pompous voice: “lt all started in a small, 5,000-watt radio station..." Around here it a!! started with a 12,000-line, decade-old Centrex system and a new hospital building going up …

The Parallel Implementation Of The Waveform Relaxation Method For Transient Stability Simulations, Marija D. Ilić, Mariesa Crow

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, the authors extend the results of their earlier paper on waveform relamtion (WR), which is a parallel algorithm for transient stability analysis. The WR algorithm is extended to a structure-preserving power system model in which the loads are retained. This results in a system of differential/ algebraic equations (DAEs). Power systems exhibit several unique dynamic properties which may be exploited in an advantageous manner by the WR algorithm. This leads to a greater computational efficiency than most other direct methods of simulation. This paper presents several theoretical results as well as computational results on parallel implementation.

Metamodeling Aspects Of Model Conceptualization, Wayne W. Wakeland

Complex Systems Faculty Publications and Presentations

This paper suggests a technique for improving the conceptualization of models. The key aspect of this technique is to set aside the main model for a period of time during the model conceptualization process and focus on building a "watchdog" submodel. The primary purpose of the watchdog submodel is to assure that the main model remains internally consistent during its operation. In the experience of this author, such a submodel can help to identify model conceptualization errors and to determine if a model is sufficiently "robust" to adequately replicate the behavior of the system being modeled.

This is not a …

Transistor-Based Measurements Of Electron Injection Currents In P-Type Gaas Doped 1018–1020 Cm-3, M. E. Klausmeier-Brown, M. R. Melloch, Mark S. Lundstrom

Department of Electrical and Computer Engineering Faculty Publications

Measurements of electron currents injected into p+‐GaAs are presented for molecular beam epitaxially grown material doped from 2×1018 to 8×1019 cm−3 with Be. The collector current versus base‐emitter voltage characteristics of n‐p+‐n GaAs homojunction bipolar transistors are analyzed, and the results are interpreted in terms of the quantity (n0Dn), where n0 is the equilibrium minority‐carrier concentration and Dn is the minority‐carrier diffusion coefficient. The results are consistent with earlier measurements of (n0Dn) made using metalorganic chemical vapor deposited p+‐n GaAs solar …

Ground Exploitation Using A Binary Phase-Only Optical Correlator, Samuel Peter Kozaitis, Sandra L. Halby, Wesley E. Foor

Electrical Engineering and Computer Science Faculty Publications

Experimental results of an optical binary phase-only correlator using aerial imagery for ground exploitation is presented. The correlator uses magnetooptic spatial light modulators (SLMs) for dynamic operation. Input images to the correlator originate from actual aerial imagery containing aircraft and a variety of distortions. Digital image processing techniques are used on images before being input into the optical correlator to enhance the performance of the system. Filters or templates used as a database for the system are derived from models of aircraft. Rotation and scale invariance is achieved through an adaptive filtering technique in which filters are displayed sequentially against …

A Review Of Recent Advances In Economic Dispatch, Badrul H. Chowdhury, S. Rahman

Electrical and Computer Engineering Faculty Research & Creative Works

A survey is presented of papers and reports that address various aspects of economic dispatch. The time period considered is 1977-88. Four related areas of economic dispatch are identified and papers published in the general areas of economic dispatch are classified into these. These areas are: optimal power flow, economic dispatch in relation to AGC, dynamic dispatch, and economic dispatch with nonconventional generation sources.

Boundary Element-Image Method Approach To Seismic Modeling, Richard E. Dubroff

Electrical and Computer Engineering Faculty Research & Creative Works

The Boundary Element-Image Method is Proposed as a Method for Generating Synthetic Seismograms in a System of Piecewise Homogeneous Layers. the Present Approach Uses the Boundary Conditions Explicitly in Order to Develop a System of Integral Equations. Although This Method Can Be Formulated in a General Way, Specific Computational Advantages Occur When the Basis and Testing Functions Are Chosen as Harmonically Related Complex Sinusoids. -From Authors

Growth Of Cdte And Cds/Cdte Heterojunctions On Metal Substrates By Spray Pyrolysis, Alok K. Berry, Jack L. Boone, Thomas P. Van Doren

Electrical and Computer Engineering Faculty Research & Creative Works

Preliminary results of the spray pyrolysis of thin films of CdTe on metal substrates are reported. The films are hard and adhere well to the substrate. A n-CdS/p-CdTe rectifying junction is also grown completely by spray pyrolysis on the metallic substrate. The ability to produce p-n junctions using the inexpensive and simple procedure of spray pyrolysis may lead to a viable process for mass production of solar cells. © 1990.

Contours Of Constant Pseudo-Brewster Angle In The Complex Є Plane And An Analytical Method For The Determination Of Optical Constants, R. M.A. Azzam, Ericson E. Ugbo

Electrical Engineering Faculty Publications

The locus of all points in the complex plane of the dielectric function є[є_r + jє_i = |є| exp(jθ)], that represent all possible interfaces characterized by the same pseudo-Brewster angle θ_pB of minimum p reflectance, is derived in the polar form: |є| = l cos(ζ/3), where l = 2(tan²Φ_pB)k, ζ = arccos(- cosθ cos²Φ_pB/k³), and k = (1 - 2/3 sin²Φ_pB)½. Families of iso-Φ_pB contours for (I) 0° ≤ Φ_pB ≤ …

Scattering By A Narrow Gap In An Impedance Plane, John R. Natzke

Faculty Publications - Department of Electrical Engineering and Computer Science

No abstract provided.

Reliability Prediction Of Vulcanized Fibre Using Electrical Noise As A Screening Parameter, George A. Donos

Theses

The main objective of this thesis was to find a correlation between the electrical noise generated within the body of Vulcanized Fibre in insulating service and the time of its breakdown under a synergy of electrical, thermal and mechanical stresses. Failure was defined as a material discontinuity, puncture, under accelerated life test conditions. Radio frequency measurements of the partial discharges occuring in the voids of the material were performed on 1240 samples of vulcanized fibre with 10 mil thickness. The level of electrical noise measured was used to classify the specimens into the three following categories: (a) Low Noise:0-2.8μV (0-9db), …

Design And Analysis Of An Intracranial Pressure And Temperature Sensor Telemetry System, Anshumat Parasar

Theses

This thesis presents a signal conditioning and telemetry system for an implantable pressure and temperature transducer. The initial target application is for measuring the epidural intracranial pressure in the range of 25-100 millitorr and temperature over the range 90 — 110° F. The implant, based on custom silicon IC design can be packaged within a volume of 2cm3 and will require surgical procedures for placement and removal. Effort has been made in this thesis to design the transducer, associated signal conditioning and telemetry circuits for useful operation over a wide range of power supply voltage. The implanted device is powered …

Adaptive Transform Coding Of Video With Motion Compensation And Vector Quantization, Jung-Hui Chien

Theses

This thesis proposes an efficient transform coding scheme for the low bit rate video sequence. The redundancy within adjacent video frame is exploited by motion compensated interframe prediction using the efficient independent orthogonal search technique, and the motion compensated frame difference (MCFD) signal is transform coding by 1-D DCT, 1-D HDCT and 2-D DCT, the coefficients are zonal masked, and vector quantizatied adaptively. The encoded MCFD as well as the motion information and variance grouping (side informations) are transmitted to the receiver to reconstruct the frame. The transform MCFD signal is classified into the four groups according to the coefficient …

Efficient Interconnection Schemes For Vlsi And Parallel Computation, Ronald I. Greenberg

Computer Science: Faculty Publications and Other Works

This thesis is primarily concerned with two problems of interconnecting components in VLSI technologies. In the first case, the goal is to construct efficient interconnection networks for general-purpose parallel computers. The second problem is a more specialized problem in the design of VLSI chips, namely multilayer channel routing. In addition, a final part of this thesis provides lower bounds on the area required for VLSI implementations of finite-state machines. This thesis shows that networks based on Leiserson's fat-tree architecture are nearly as good as any network built in a comparable amount of physical space. It shows that these "universal" networks …

A Cad For Edif Pattern Generation, Mohammad Akram Khan

Theses

Generating a set of test vector for a digital circuit is the most critical step in design and test. It is very important to generate test sequence easily and efficiently. The importance is enhanced by the fact that the simulation database is being used to create test programs. A CAD tool ATPG (Automatic Test Pattern Generator) has been developed to specify and satisfy requirements of designers and test engineers. EDIF (Electronic Design Interchange Format) is followed closely. EDIF targets compatability among foundry services and CAD/CAE systems.