Digital Commons Network^™

Signal Processing Of An Ecg Signal In The Presence Of A Strong Static Magnetic Field, Aditya Gupta

Electronic Theses and Dissertations

This dissertation addresses the problem of elevation of the T wave of an electrocardiogram (ECG) signal in the magnetic resonance imaging (MRI). In the MRI, due to the strong static magnetic field the interaction of the blood flow with this strong magnetic field induces a voltage in the body. This voltage appears as a superimposition at the locus of the T wave of the ECG signal. This looses important information required by the doctors to interpret the ST segment of the ECG and detect diseases such as myocardial infarction. This dissertation aims at finding a solution to the problem of …

A Comparison And Evaluation Of Common Pid Tuning Methods, Justin Youney

Electronic Theses and Dissertations

The motivation behind this thesis is to consolidate and evaluate the most common Proportional Integral Derivative (PID) controller tuning techniques used in industry. These are the tuning techniques used when the plant transfer function is not known. Many of these systems are poorly tuned because such consolidated information is not easily found in one single source such as this thesis. Once one of the tuning methods are applied almost always there will be further fine tuning needed to bring the system into the required design criteria. The purpose here is to find out which tuning technique will yield the lowest …

Polarisation Dependence Of Bend Loss For A Standard Singlemode Fiber, Qian Wang, Ginu Rajan, Pengfei Wang, Gerald Farrell

Articles

Polarization dependence of bend loss caused by the polymer coating layer for a standard singlemode fiber (SMF28) is investigated theoretically and experimentally. Bend loss for SMF28 for both the TE and TM mode is calculated separately. Normalized polarization dependent loss is proposed for the characterization of the polarization sensitivity of bend loss for different bend radii. Corresponding experimental tests are presented, which agree with the theoretical results. Both the theoretical and experimental results show that the polymer coating layer has a significant influence on the polarization dependence of bend loss.

Campus Communications Systems: Converging Technologies, The Association For Communications Technology Professionals In Higher Education

ACUTA: Other Publications

This book is a rewrite of Campus Telecommunications Systems: Managing Change, a book that was written by ACUTA in 1995. In the past decade, our industry has experienced a thousand-fold increase in data rates as we migrated from 10 megabit links (10 million bits per second) to 10 gigabit links (10 billion bits per second), we have seen the National Telecommunications Policy completely revamped; we have seen the combination of voice, data, and video onto one network; and we have seen many of our service providers merge into larger corporations able to offer more diverse services. When this book was …

Evolvable Reconfigurable Hardware Framework For Edge Detection, Nader I. Rafla

Electrical and Computer Engineering Faculty Publications and Presentations

Systems on Reconfigurable Chips contain rich resources of logic, memory, and processor cores on the same fabric. This platform is suitable for implementation of Evolvable Reconfigurable Hardware Architectures (ERHA). It is based on the idea of combining reconfigurable Field Programmable Gate Arrays (FPGA) along with genetic algorithms (GA) to perform the reconfiguration operation. This architecture is a suitable candidate for implementation of early-processing stage operators of image processing such as filtering and edge detection. However, there are still fundamental issues need to be solved regarding the on-chip reprogramming of the logic. This paper presents a framework for implementing an evolvable …

Comparison Of Single Stage And Two Stage Stage Grid-Tie Inverters, Keith Mansfield

Electronic Theses and Dissertations

This thesis compares two methods of designing grid-tie inverters. The first design topology is a traditional two stage approach consisting of an isolated DC-DC converter on the input followed by a high switching frequency SPWM (Sinusoidal Pulse Width Modulation) stage to produce the required low frequency sine wave output. The novel second design approach employs a similar DC-DC input stage capable of being modulated to provide a rectified sine wave output voltage/current waveform. This stage is followed by a simple low frequency switched Unfolding Stage to recreate the required sine wave output. Both of the above designs have advantages and …

Infrared Antenna-Coupled Phased-Array, Christopher Middlebrook

Electronic Theses and Dissertations

Phased-array antennas are commonplace in the radiofrequency portion of the electromagnetic spectrum. Exploitation of phasing effects between multiple antennas facilitates a wide range of applications, including synthetic-aperture radar, beam forming, and beam scanning. For the first time, the phased addition of multiple dipole antennas is demonstrated in the infrared, at a wavelength of 10.6 micrometers. Coplanar strip lines are used to interconnect the antennas, preserving the phase of the individual contributions. Several different proof-of-concept experiments are performed, using planar antennas fabricated with direct-write electron-beam lithography. Infrared-frequency currents from two dipole antennas are summed together at a common feedpoint and dissipated …

High-Speed Modelocked Semiconductor Lasers And Applications In Coherent Photonic Systems, Wangkuen Lee

Electronic Theses and Dissertations

1.55-µm high-speed modelocked semiconductor lasers are theoretically and experimentally studied for various coherent photonic system applications. The modelocked semiconductor lasers (MSLs) are designed with high-speed (>5 GHz) external cavity configurations utilizing monolithic two-section curved semiconductor optical amplifiers. By exploiting the saturable absorber section of the monolithic device, passive or hybrid mode-locking techniques are used to generate short optical pulses with broadband optical frequency combs. Laser frequency stability is improved by applying the Pound-Drever-Hall (PDH) frequency stabilization technique to the MSLs. The improved laser performance after the frequency stabilization (a frequency drifting of less than 350 MHz), is extensively studied …

Susceptibility Scanning System As Failure Analysis Tool For System Level Esd Problems, Giorgi Muchaidze

Masters Theses

"System level Electrostatic Discharges (ESDs) can lead to soft-errors (e.g., bit-errors, wrong resets). The goal of this project is to offer guidance in finding the root cause of soft-errors frequently observed using immunity scanning system. Immunity scanning is an increasingly adopted method for root cause analysis of system level immunity sensitivities. It allows localizing affected nets and ICs. At first a description of the ESD discharge process is given, which provides the necessary background for correctly analyzing ESD failures. Local scanning and in-circuit measurement techniques are expounded in this study. Further, it is shown how PCB scanning results can reveal …

Bga Footprints Modeling And Physics Based Via Models Validation For Power And Signal Integrity Applications, Giuseppe Selli

Doctoral Dissertations

"Modeling and simulating the multi-scale nature of a power distribution network (PDN) is essential to ensure the correct functioning of the devices connected to it. Simple parallel-plate sections constitute the core of these PDN geometries, together with sections where a large number of holes and vias are present, as in the case of a BGA footprint. Employing a divide-and-conquer approach allows for the modeling of these geometries separately, i.e., 3-D full wave solvers for the sections with holes and vias, and a cavity model approach, for the simple parallel-plate structures. Also, equivalent circuit models can be obtained for time-domain and …

Mobile Array Designs With Anserlin Antennas And Efficient, Wide-Band Peec Models For Interconnect And Power Distribution Network Analysis, Michael A. Cracraft

Doctoral Dissertations

"A mobile, wide-band antenna system has been developed around the ANSERLIN antenna element and a 3-dB splitter design. The size of the antenna elements was reduced over previous versions by introducing dielectric substrates. Additionally, new variations of the antenna were designed to influence radiation characteristics. To further reduce the number of components in the array, a very low profile splitter was designed and mounted below one of the antenna elements, doubling as the return plane for the antenna. The partial-element equivalent circuit (PEEC) method has been used for 3D interconnect analysis and numerous other applications. Being based on the same …

Decoupling And Disturbance Rejection Control For Target Circulation, Jian Ma, Joon S. Lee, Woosoon Yim

Reactor Campaign (TRP)

In 1998, the Institute of Physics and Power Engineering (IPPE) and Experimental and Development Organization “Gidropress” in Russia, began the design and construction of a prototype lead-bismuth eutectic (LBE) accelerator target, the Target Complex 1 (TC-1), under the International Science and Technology Center (ISTC) project #559 (“Pilot Flow Lead-Bismuth Target of 1 MW Power for Accelerator Driven Systems”) in support of the international efforts to develop accelerator-driven spallation systems for nuclear transmutation and other applications.

During the thermal and engineering test of the TC-1 in 2005 at UNLV, it was observed that the existing control algorithm led to a very …

A Method To Measure Reference Strain In Fbg Strain Sensor Interrogation System Involving Actuators, Ginu Rajan, Yuliya Semenova, Qian Wang, Gerald Farrell, Pengfei Wang

Articles

A method for reference strain measurement for FBG strain sensor in the testing stage while applying strain using actuators like piezo translators or micro screw is introduced. Unlike conventional methods of surface mounting, in our method the strain gauge is affixed directly to the optical fibre, which allows it to use with systems where the strain is applied directly using actuators while testing the FBG sensing system. Different bonding techniques were tested and a comparison with the results from calculated values are presented. Since the contact area between the fibre and strain gauge is very small a corrected gauge factor …

Modelling A Deposition Process In Collective Construction, Robert L. Stewart, R. Andrew Russell, Lindsay Kleeman

Turkish Journal of Electrical Engineering and Computer Sciences

During collective construction tasks, swarm robots coordinate their actions in space and time to build structures that conform to some given design or specification. In this paper, a simulation model and a mathematical model (based on a Markov chain) are introduced to describe the deposition process of a previously detailed robotic swarm system that uses templates and feedback to facilitate construction. The models are based on the behaviour and geometry of real robots and predict the dynamics observed during practical trials as well as explaining the occurrence of different spatial patterns of building blocks. Furthermore, the models provide an insight …

Swarms In Biology And Engineering, Kevin M. Passino

Turkish Journal of Electrical Engineering and Computer Sciences

No abstract provided.

Data Mining And Costas Arrays, Konstantinos Drakakis

Turkish Journal of Electrical Engineering and Computer Sciences

Costas arrays are used in RADAR (and SONAR) engineering to represent frequency-hopping patterns that optimize the RADAR's performance. In this work, using all available Costas arrays up to and including order 26, as well as data mining techniques, we investigate how the Costas property and the balance of signs in the difference triangle of a permutation are related. Our conclusion is that there is sufficient evidence to believe that the mechanism responsible for the formation of Costas arrays changes from low to high orders.

A Review Of Studies In Swarm Robotics, Levent Bayindir, Erol Şahi̇n

Turkish Journal of Electrical Engineering and Computer Sciences

Swarm robotics is a new approach to the coordination of large numbers of relatively simple robots. The approach takes its inspiration from the system-level functioning of social insects which demonstrate three desired characteristics for multi-robot systems: robustness, flexibility and scalability. In this paper we have presented a preliminary taxonomy for swarm robotics and classified existing studies into this taxonomy after investigating the existing surveys related to swarm robotics literature. Our parent taxonomic units are modeling, behavior design, communication, analytical studies and problems. We are classifying existing studies into these main axes. Since existing reviews do not have enough number of …

Aggregation In Swarm Robotic Systems: Evolution And Probabilistic Control, Onur Soysal, Erki̇n Bahçeci̇, Erol Şahi̇n

Turkish Journal of Electrical Engineering and Computer Sciences

In this study we investigate two approachees for aggregation behavior in swarm robotics systems: Evolutionary methods and probabilistic control. In first part, aggregation behavior is chosen as a case, where performance and scalability of aggregation behaviors of perceptron controllers that are evolved for a simulated swarm robotic system are systematically studied with different parameter settings. Using a cluster of computers to run simulations in parallel, four experiments are conducted varying some of the parameters. Rules of thumb are derived, which can be of guidance to the use of evolutionary methods to generate other swarm robotic behaviors as well. In the …

A New Relaying Algorithm To Detect Loss Of Excitation Of Synchronous Generators, Ömer Usta, M. H. Musa, M. Bayrak, M.A. Redfern

Turkish Journal of Electrical Engineering and Computer Sciences

A new digital relaying algorithm is introduced for the protection of synchronous generators against loss of excitation conditions. The new algorithm is based on measuring of the 3-phase reactive power output of the machines, and monitors the direction and magnitude of leading reactive power at the generator terminal. The protection algorithm is designed such that it can provide reliable protection against loss of field conditions and remains stable during recoverable power system swing conditions. While the new relay produces a trip signal for partial loss of field conditions causing the machine to lose its stability, it remains stable for the …

A Sensitive Ann Based Differential Relay For Transformer Protection With Security Against Ct Saturation And Tap Changer Operation, Hassan Khorashadi Zadeh, Zuyi Li

Turkish Journal of Electrical Engineering and Computer Sciences

This paper presents an artificial neural network (ANN) based scheme for fault identification in power transformer protection. The proposed scheme is featured by the application of ANN to identifying system patterns, the unique choice of harmonics of positive sequence differential currents as ANN inputs, the effective handling of current transformer (CT) saturation with an ANN based approach, and the consideration of tap changer position for correcting secondary CT current. Performance of the proposed scheme is studied for a wide variety of operating conditions using data generated from simulation. The results indicate that the proposed scheme provides a fast and sensitive …

Study Of The Warranty Cost Model For Software Reliability With An Imperfect Debugging Phenomenon, D.R. Prince Williams

Turkish Journal of Electrical Engineering and Computer Sciences

Software reliability is one of the most important characteristics of software quality. Its measurement and management technologies employed during the software life-cycle are essential for producing and maintaining quality/reliable software systems. Herein, we discuss a modified approach to calculating the delivery cost of a software product, when warranty is to be provided, with an imperfect debugging phenomenon. Unlike existing cost models, here the strategy was to consider maintenance support given to the customer with an imperfect debugging phenomenon. The optimal release time can be calculated for various reliability levels by minimizing the cost. The delivery cost, reliability of the software …

Reactive Oxygen Emission From Microwave Discharge Plasmas, S. Popovic, M. Rašković, S. P. Kuo, L. Vuskovic

Physics Faculty Publications

Metastable oxygen atoms and molecules have received increased interest because of their function in surface modification, bio-decontamination and many other industrial applications, in addition to the role in the upper atmospheric layer chemistry. We review work on production and detection of metastable oxygen and we describe our experiments, including the development of techniques for measurement of metastable molecular oxygen. We show that either metastable oxygen molecules or metastable oxygen atoms can be produced in large quantities in electrical discharges, carefully tailored to promote the required kinetics. Although the two species may coexist, colder discharge regimes favor production of molecules, while …

Analysis Of A Small-Signal Model Of A Pwm Dc-Dc Buck-Boost Converter In Ccm, Julie Joann Lee

Browse all Theses and Dissertations

The objective of this research is to analyze and simulate the pulse-width-modulated (PWM) dc-dc buck-boost converter and design a controller to gain stability for the buck-boost converter. The PWM dc-dc buck-boost converter reduces and/or increases dc voltage from one level to a another level in devices that need to, at different times or states, increase or decrease the output voltage.

In this thesis, equations for transfer funtions for a PWM dc-dc open-loop buck-boost converter operating in continuous-conduction-mode (CCM) are derived. For the pre-chosen design, the open-loop characterics and the step responses are studied. The converter is simulated in PSpice to …

Detection Of Flash In Dermoscopy Skin Lesion Images, Radhika Nagane

Masters Theses

"Dermoscopy images of skin lesions are often acquired by covering the skin with mineral oil, alcohol, another liquid or a gel and illuminating the area at a low angle of incidence from all directions before taking the photograph. Deeper pigment patterns are more visible in this type of image than in a clinical image because the liquid immersion and structured light effectively make the upper layers of the skin more transparent. Flash regions are the small, high reflectance areas in the image where direct reflections of the illumination source(s) cause undesirable bright spots in the image. These flash regions may …

Performance Improvement Of Adaptive Filters For Echo Cancellation Applications, Deepak Challa

Masters Theses

"This work focuses on performance improvement of adaptive algorithms for both line and acoustic echo cancellation applications. Echo in telephone networks, Line Echo, is observed naturally due to impedance mismatches at the long-distance/local-loop interface. Acoustic echo is due to the acoustic coupling between the microphone and the speaker of a speakerphone. The Affine Projection (APA) and the Fast Affine Projection (FAP) algorithms are two examples of reliable and efficient adaptive filters used for echo cancellation...This thesis presents, Variable Regularized Fast Affine Projections (VR-FAP) algorithm, with a varying, optimal regularization value which provides the desirable property of both fast and low …

Operation Of A Brushless Dc Drive For Application In Hybrid Electric Vehicles, James Scott Jenkins

Masters Theses

"One of the goals of a hybrid electric vehicle design is to improve the overall performance of the vehicle by incorporating several different power sources in such a way as to maximize the energy usage. By combining the desirable characteristics of each of the components in the system, the vehicle becomes more efficient to operate. Energy storage systems such as batteries and ultra-capacitors can be used to supply or store energy from the system when needed. The primary power source in this model will be an internal combustion engine coupled with a permanent magnet synchronous generator. The purpose of this …

Performance Improvements Of Automobile Communication Protocols In Electromagnetic Interference Environments, Fei Ren

Masters Theses

"Electromagnetic Interference (EMI) is frequently encountered in automobile communication systems due to a large number of inductive nodes used in these systems. This thesis investigates the effects of EMI on two types of automobile communication systems, the Controller Area Network (CAN) and the FlexRay. It also proposes a modified Automatic Repeat reQuest (ARQ) scheme to improve the communication performances in EMI environments"--Abstract, page iii.

Fast Sphere Decoder For Mimo Systems, Praveen G. Krishnan

Masters Theses

"This work focuses on variants of the conventional sphere decoding technique for Multi Input Multi Output (MIMO) systems. Space Time Block Codes (STBC) have emerged as a popular way of transmitting data over multiple antennas achieving the right balance between diversity and spatial multiplexing. The Maximum Likelihood (ML) technique is a conventional way of decoding the transmitted information from the received data, but at the cost of increased complexity. The sphere decoder algorithm is a sub-optimal decoding technique that is computationally efficient achieving a ;symbol error rate that is dependent on the initial radius of the sphere. In this thesis, …

Characterization Of Noise On Pdn And Electromagnetic Shielding, Sandeep K. R. Chandra

Masters Theses

"Modern FPGA and microprocessor have complex logic inside them, which draw current from the Power Distribution Network (PDN). This current drawn from the PDN creates disturbance on the PDN, which then propagates to other IC in different places on the Printed Circuit Board (PCB), and appears as a noise voltage. Ability to predict noise voltage at any point on the PCB gives a greater ability to carefully design the board and the PDN. In order to accurately predict the noise, it is important to accurately predict the current drawn and the transfer impedance from the source to the victim point. …

Artificial Immune System Based Algorithms For Optimization And Self-Tuning Control In Power Systems, Mani Hunjan

Masters Theses

"Artificial immune systems (AIS) are new computational intelligence methods inspired by various mechanisms of the biological immune system. AIS are adaptive systems inspired by theoretical immunology and its functions, principles and models. The work depicted in this thesis centers on the applications of AIS based algorithms for optimization and self-tuning control in power systems. The optimization is carried out using an algorithm based on the clonal selection principle and the self-tuning characteristics of control for parameters are inspired by the humoral immune response of the human body. The work in this thesis is written in two papers as follows: Paper …