Digital Commons Network^™

Optimal Channel Equalization For Filterbank Transceivers In Presence Of White Noise, Ehab Farouk Badran

LSU Doctoral Dissertations

Filterbank transceivers are widely employed in data communication networks to cope with inter-symbol-interference (ISI) through the use of redundancies. This dissertation studies the design of the optimal channel equalizer for both time-invariant and time-varying channels, and wide-sense stationary (WSS) and possible non-stationary white noise processes. Channel equalization is investigated via the filterbank transceivers approach. All perfect reconstruction (PR) or zero-forcing (ZF) receiver filterbanks are parameterized in an affine form, which eliminate completely the ISI. The optimal channel equalizer is designed through minimization of the mean-squared-error (MSE) between the detected signals and the transmitted signals. Our main results show that the …

Three-Dimensional Micromachined On-Chip Inductors For High Frequency Applications, Nimit Chomnawang

LSU Doctoral Dissertations

Demands for wireless communication are ever-escalating for consumer and military communication applications. The requirements of portability, more functionality and lower cost have been driving forces toward smaller, more sophisticated and flexible wireless devices with lower power consumption. To meet these requirements, monolithically integrated passive inductors with high Q-factors and high self-resonant frequencies are desirable. Q-factor and self-resonant frequency of an inductor are significantly degraded at high frequencies due to conductor ohmic loss, magnetically induced eddy current in the conductive substrate, and lower self-resonant frequency from capacitance between conductive substrate and conductors.
In this dissertation, novel three-dimensional arch-like solenoid and dome-shaped …

Reducing Power Bus Impedance At Resonance With Lossy Components, Todd H. Hubing, Theodore M. Zeeff

Electrical and Computer Engineering Faculty Research & Creative Works

Power bus structures in printed circuit boards with solid power and ground planes exhibit resonances. When the power bus is resonant, the power bus impedance can increase dramatically. This paper explores the effect of component equivalent series resistance (ESR) on power bus resonances. General guidelines for selecting an optimum ESR are provided and are supported by laboratory measurements and numerical simulations.

Development Of A Program For Numerical Analysis Of Microwave Radio Links Under Different Conditions, M. Can, Sergey Kharkovsky

Electrical and Computer Engineering Faculty Research & Creative Works

Numerical analysis of system power budget is performed for radio link design and transmission planning purposes in cellular networks. The behavior of three different frequencies; 10.5 GHz, 23 GHz and 38 GHz is examined under the influence of such parameters like transmitter power output level, rain rate, fog density, distance, polarization type, antenna radius, temperature, foliage depth and etc. Received power levels are measured, calculated and reported for different radio link types and environmental conditions. A new program is developed in order to carry out system power budget analysis and design better microwave radio links. Measured and calculated values are …

On The Interior Resonance Problem When Applying A Hybrid Fem/Mom Approach To Model Printed Circuit Boards, Yun Ji, Todd H. Hubing

Electrical and Computer Engineering Faculty Research & Creative Works

A hybrid finite element method/method of moments (FEM/MoM) technique is used to analyze a printed circuit board power bus structure where the source and observation points are in the near field. The FEM is used to model the lossy region between the planes of the board including the source. The MoM is used to model the region outside the planes and provide a radiation boundary condition to terminate the FEM mesh. Numerical results for a bridged power bus structure are compared with measurements. A nonphysical interior resonance of the electric field integral equation is observed. The problem can be avoided …

End To End Congestion Control In High-Speed Networks, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

This paper proposes an adaptive methodology to prevent congestion in packet switched networks such as the Internet, where the internal network nodes convey very little information to the ingress nodes. Two architectures of preventing the congestion are presented: the first one when the traffic arrival rates, and bottleneck queue levels are known and the other when these are unknown. In the latter, the network traffic is estimated online using an adaptive system by measuring the buffer occupancy. In both architectures, the congestion is controlled by adjusting the transmission rates of non real-time and certain real-time sources in response to the …

Distributed Power Control In Wireless Communication Systems, Sarangapani Jagannathan, A. T. Chronopoulos, S. Ponipireddy

Electrical and Computer Engineering Faculty Research & Creative Works

Energy efficiency is a measure of performance in wireless networks. Therefore, controlling the transmitter power at a given node increases not only battery operating life, but also overall system capacity by successfully admitting new links. It is essential to find effective means of power control in point-to-point, broadcasting and multicasting scenarios. Wireless networking presents formidable challenges, and we consider the problem of unicast or point-to-point (peer-to-peer) communication in wireless networks in the presence of other nodes. We study the feasibility of admitting new links in an wireless network operating area while maintaining quality of service (QoS), in terms of signal-to-interference …

A Hybrid System Theoretic Approach For Admission Controller Design In Multimedia Networks, Sarangapani Jagannathan

Electrical and Computer Engineering Faculty Research & Creative Works

A novel real-time discrete-event admission control (AC) scheme for high-speed networks is proposed with the aim of attaining a desired quality of service (QoS) and high network utilization. The AC uses the available capacity from a novel adaptive bandwidth estimation scheme, a congestion indicator derived from a congestion controller, peak bit/cell rate (PBR/PCR) estimate from new sources, along with the desired QoS metrics, and makes decisions whether to 'admit' or 'reject' new sources. The novel aspect of the proposed approach is the application of hybrid system theory to prove the performance of the admission controller, stability and the development of …

Term Trees In Application To An Effective And Efficient Atpg For And–Exor And And–Or Circuits, Lech Jozwiak, Aleksander Ślusarczyk, Marek Perkowski

Electrical and Computer Engineering Faculty Publications and Presentations

A compact data representation, in which the typically required operations are performed rapidly, and effective and efficient algorithms that work on these representations are the essential elements of a successful CAD tool. The objective of this paper is to present a new data representation—term trees (TTs)—and to discuss its application for an effective and efficient structural automatic test-pattern generation (ATPG). Term trees are decision diagrams similar to BDDs that are particularly suitable for structure representation of AND–OR and AND–EXOR circuits. In the paper, a flexible algorithm for minimum term-tree construction is discussed and an effective and efficient algorithm for ATPG …

Second-Order Statistical Properties Of The Wss Jakes' Fading Channel Simulator, Chengshan Xiao, Y. Rosa Zheng, N. C. Beaulieu

Electrical and Computer Engineering Faculty Research & Creative Works

An improved Jakes' (1994) fading channel simulator was proposed by Pop and Beaulieu (see ibid., vol.49, p.699-708, Apr. 2001) to eliminate the stationarity problem occurring in Jakes' original design. In this paper, second-order statistical properties of the improved Jakes' simulator are analyzed. Consistent with Pop and Beaulieu's caution about high-order statistics of the simulator, it is proved that some second-order statistics of both the quadrature components and the envelope do not match the desired ones even if the number of sinusoids approaches infinity. Therefore, care must be taken when the simulator is employed to evaluate algorithms and systems.

Measurement And Monitoring Of Microwave Reflection And Transmission Properties Of Cement-Based Specimens, Sergey Kharkovsky, M. F. Akay, U. C. Hasar, C. D. Atis

Electrical and Computer Engineering Faculty Research & Creative Works

The results of measurement and monitoring of reflection and transmission properties of cement-based specimens (blocks of mortar, concrete) obtained by using a simple and an inexpensive measurement system at microwave frequencies (X-band) are presented. Dependencies of the reflection and transmission coefficients on water-to-cement (w/c) ratio, preparing and curing conditions of the specimens are demonstrated. It is shown that the amplitudes of reflection and transmission coefficients, together with thickness of the specimens, determine the complex dielectric permittivity of the hardened cement-based specimens. The expected applications of the results for the determination of physical properties of cement-based materials are discussed. The causes …

Interactive Virtual Laboratory For Experience With A Smart Bridge Test, Elizabeth C. Eckhoff, Vicki M. Eller, Steve Eugene Watkins, Richard Hall

Electrical and Computer Engineering Faculty Research & Creative Works

Virtual laboratory experiments can be cost effective, convenient instructional resources that have appeal to a wide range of learning styles. Expensive, time-consuming laboratory tests can be experienced repeatedly and remotely using interactive simulations and original video footage or animations. A virtual experiment can incorporate meaningful exercises, procedural options, and background hyperlinks to create a comprehensive "hands on" environment. Also, it may be used as preliminary training for the actual experiment.

An interactive LabVIEW-based laboratory for a load test simulation of an existing demonstration bridge was created. This smart truss bridge is instrumented with fiber optic strain sensors situated on the …

Interdisciplinary Graduate Experience: Lessons Learned, Steve Eugene Watkins, V. M. Eller, Josh Corra, M. J. Molander, Bethany Konz, Richard H. Hall, K. Chandrashekhara, Abdeldjelil Belarbi

Electrical and Computer Engineering Faculty Research & Creative Works

Engineers interact in the workplace with technical peers in other disciplines at all stages of design, development, and application. Awareness of the constraints and needs of the other disciplines can be key in many situations. Such interdisciplinary activity and the associated communication are facilitated if the all participants have a solid knowledge of discipline-specific terminology and an understanding of connecting concepts. Consequently, experience relating to interdisciplinary teamwork is a necessary component of engineering education. The Smart Engineering Group at the University of Missouri-Rolla was established to conduct interdisciplinary research and to create interdisciplinary educational resources. The topical interest area is …

Design And Analysis Of Optical Layouts For Free Space Optical Switching, Kung-Meng Lo

Theses: Doctorates and Masters

The Intelligent Reconfigurable Optical Switch (IROS) is an N x N optical switch that uses two reflective Liquid Crystal (LC) Spatial Light Modulators (SLM} in a "Z" configuration to steer the incoming beams from the input ports to the designated output ports. Currently, the maximum steering capacity of practical SLM is limited to few degrees. For a dense optical switch, this makes the optical path between the input and output fiber ports relatively long. When a Gaussian beam is switched from an input fiber port to an output fiber port in a long free space interconnection topology, the beam's illumination …

Modulation Classification Of Digital Communication Signals, Visalakshi S. Ramakonar

Theses: Doctorates and Masters

Modulation classification of digital communications signals plays an important role in both military and civilian sectors. It has the potential of replacing several receivers with one universal receiver. An automatic modulation classifier can be defined as a system that automatically identifies the modulation type of the received signal given that the signal exists and its parameters lie in a known range. This thesis addresses the need for a universal modulation classifier capable of classifying a comprehensive list of digital modulation schemes. Two classification approaches are presented: a decision-theoretic (DT) approach and a neural network (NN) approach. First classifiers are introduced …

Dynamic Modelling Of A Two-Stage Atm Tandem Banyan Switch, Hon Loke Tham

Student Works (2000-2009)

This dissertation studies the dynamic modelling of Two-State ATM Tandem Banyan Switch. First of all, ATM technology and ATM switch are introduced, then the ATM switch's architecture and its functions are discussed in detail. A Two-State ATM Tandem Banyan Switch has been selected as a model to be simulated. MATLAB's Simulink tool has been used to dynamically model the ATM switch. The ATM switch simulated is a simple two-stage Banyan Switch. It consists of 2 lnports x 2 Outports, with a switching algorithm included. The algorithm covers all cell flow patterns that are possible in a 2 lnports x 2 …

Two-Dimensional Fast Evanescent Wave Algorithm, W. C. Chew, L. (Lijun) J. Jiang, S. Velamparambil

Electrical and Computer Engineering Faculty Research & Creative Works

A new fast evanescent wave algorithm (FEWA) is introduced in the two-dimensional (2-D) case. It expands the Green's function into propagating waves and directional evanescent waves. Applying the evanescent wave correction technique, a procedure similar to the traditional MLFMA can be expedited. No buffer region is necessary anymore, and fewer translators are needed. Numerical examples are given to show the features of this method.

Nonlinear Suppression Of Range Ambiguity In Pulse Doppler Radar, Jon M. Anderson

Theses and Dissertations

Coherent pulse train processing is most commonly used in airborne pulse Doppler radar, achieving adequate transmitter/receiver isolation and excellent resolution properties while inherently inducing ambiguities in Doppler and range. First introduced by Palermo in 1962 using two conjugate LFM pulses, the primary nonlinear suppression objective involves reducing range ambiguity, given the waveform is nominally unambiguous in Doppler, by using interpulse and intrapulse coding (pulse compression) to discriminate received ambiguous pulse responses. By introducing a nonlinear operation on compressed (undesired) pulse responses within individual channels, ambiguous energy levels are reduced in channel outputs. This research expands the NLS concept using discrete …

Testing Exception And Error Cases Using Runtime Fault Injection, James A. Whittaker, Florence E. Mottay, Ibrahim K. El-Far

Electrical Engineering and Computer Science Faculty Publications

Fault injection deals with the insertion or simulation of faults in order to test the robustness and fault tolerance of a software application. Such measures are generally performed on software that is mission critical, to the extent that failure could have significant negative ramifications. Actual injection of faults can be performed either at compile time, when additional code is inserted to force error conditions to evaluate to true, or at runtime during which faults are injected into the software's execution environment. This paper focuses on the latter type of fault injection and presents a new mechanism for inserting environmental faults. …

Survivable Mobile Operating System, James Whittaker, Mohommad Samarah

Electrical Engineering and Computer Science Faculty Publications

Although there is a large body of work on cryptographic techniques and algorithms that provide basic building blocks to solve specific security problems, relatively little work has been done in investigating security issues in mobile system contexts. Conventional security controls work well for static code, but break down with code mobility. In this paper, we investigate the need for end-to-end security in mobile and wireless operating systems. We study the implications of mobility - specifically, ways in which the operating system may facilitate communication security. We suggest a framework for designing security into mobile devices by building encryption into the …

Techniques For The Regeneration Of Wideband Speech From Narrowband Speech, Jason A. Fuemmeler, Russell C. Hardie, William R. Gardner

Electrical and Computer Engineering Faculty Publications

This paper addresses the problem of reconstructing wideband speech signals from observed narrowband speech signals. The goal of this work is to improve the perceived quality of speech signals which have been transmitted through narrowband channels or degraded during acquisition. We describe a system, based on linear predictive coding, for estimating wideband speech from narrowband. This system employs both previously identified and novel techniques. Experimental results are provided in order to illustrate the system’s ability to improve speech quality. Both objective and subjective criteria are used to evaluate the quality of the processed speech signals.

Projection-Based Image Registration In The Presence Of Fixed-Pattern Noise, Ernest Armstrong, Stephen C. Cain, Majeed M. Hayat

Electrical and Computer Engineering Faculty Research and Publications

A computationally efficient method for image registration is investigated that can achieve an improved performance over the traditional two-dimensional (2-D) cross-correlation-based techniques in the presence of both fixed-pattern and temporal noise. The method relies on transforming each image in the sequence of frames into two vector projections formed by accumulating pixel values along the rows and columns of the image. The vector projections corresponding to successive frames are in turn used to estimate the individual horizontal and vertical components of the shift by means of a one-dimensional (1-D) cross-correlation-based estimator. While gradient-based shift estimation techniques are computationally efficient, they often …

Power System Deregulation, Mariesa Crow

Electrical and Computer Engineering Faculty Research & Creative Works

Given the difficulties encountered by the state of California in deregulating their electric power industry, many people are questioning the wisdom of such a move. To better understand the motivation behind deregulation, the author looks at the cost of energy nationwide in the United States. For example, she considers some of the regional energy costs from August 2001.

Energy Storage Systems For Advanced Power Applications, Aysen Arsoy, Yilu Liu, Paul F. Ribeiro, Brian K. Johnson, Mariesa Crow

Electrical and Computer Engineering Faculty Research & Creative Works

While energy storage technologies do not represent energy sources, they provide valuable added benefits to improve stability power quality, and reliability of supply. Battery technologies have improved significantly in order to meet the challenges of practical electric vehicles and utility applications. Flywheel technologies are now used in advanced nonpolluting uninterruptible power supplies. Advanced capacitors are being considered as energy storage for power quality applications. Superconducting energy storage systems are still in their prototype stages but receiving attention for utility applications. The latest technology developments, some performance analysis, and cost considerations are addressed. This paper concentrates on the performance benefits of …

Greenland Snow Accumulation Estimates From Satellite Radar Scatterometer Data, Mark R. Drinkwater, David G. Long, Andrew W. Bingham

Faculty Publications

Data collected by the C band ERS-2 wind scatterometer (EScat), the Ku band ADEOS-1 NASA scatterometer (NSCAT), and the Ku band SeaWinds on QuikScat (QSCAT) satellite instruments are used to illustrate spatiotemporal variability in snow accumulation on the Greenland ice sheet. Microwave radar backscatter images of Greenland are derived using the scatterometer image reconstruction (SIR) method at 3-day intervals over the periods 1991–1998 and 1996–1997 for EScat and NSCAT, respectively. The backscatter coefficient σ° normalized to 40° incidence, A, and gradient in backscatter, B, in the range 20°–60° are compared with historical snow accumulation data and recent measurements …

A Fast Full-Search Adaptive Vector Quantizer For Video Coding, Scott E. Budge, Christian B. Peel

Electrical and Computer Engineering Faculty Publications

This paper presents a novel VQ structure which provides very good quality encoding for video sequences and exploits the computational savings gained from a fast-search algorithm. It uses an adaptive-search, variable-length encoding method which allows for very fast matching of a wide range of transmission rates. Both the encoding quality and the computational benefits from the fast-search algorithm are presented. Simulations show that full-search tree residual VQ (FTRVQ) can provide up to 3 dB improvement over a similar RVQ encoder on video sequences.

Dc Power-Bus Modeling And Design With A Mixed-Potential Integral-Equation Formulation And Circuit Extraction, Jun Fan, James L. Drewniak, Hao Shi, James L. Knighten

Electrical and Computer Engineering Faculty Research & Creative Works

Application of a circuit extraction approach based on a mixed-potential integral equation formulation (CEMPIE) for dc power-bus modeling in high-speed digital designs is detailed herein. Agreement with measurements demonstrates the effectiveness of the approach. Dielectric losses are included into the calculation of Green's functions, and thus, incorporated into the rigorous first principles formulation. A SPICE model is then extracted from the discretized integral equation. A quasistatic approximation is used for Green's functions to keep the extracted circuit elements frequency independent. Previous work has established a necessary meshing criterion in order to ensure accuracy for a given substrate thickness and dielectric …

Dc Power-Bus Design Using Fdtd Modeling With Dispersive Media And Surface Mount Technology Components, Xiaoning Ye, Marina Koledintseva, Min Li, James L. Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

DC power-bus modeling in high-speed digital design using the finite-difference time-domain (FDTD) method is demonstrated herein. The dispersive character of the dielectric layers used in printed circuit board substrates is taken into account in this study. In particular, FR-4 is considered. The complex permittivity of the dielectric is approximated by a Debye model. A wide-band frequency response (100 MHz-5 GHz) is obtained through a single FDTD simulation. Good agreement is achieved between the modeled and measured results for a typical dc power-bus structure with multiple surface mount technology (SMT) decoupling capacitors placed on the printed circuit board (PCB). The FDTD …

Statistical Evaluation Of Image Quality Measures, Ismail Avcibas, Bulent Sankur, Khalid Sayood

Department of Electrical and Computer Engineering: Faculty Publications

In this work we comprehensively categorize image quality measures, extend measures defined for gray scale images to their multispectral case, and propose novel image quality measures. They are categorized into pixel difference-based, correlation-based, edge-based, spectral-based, context-based and human visual system (HVS)-based measures. Furthermore we compare these measures statistically for still image compression applications. The statistical behavior of the measures and their sensitivity to coding artifacts are investigated via analysis of variance techniques. Their similarities or differences are illustrated by plotting their Kohonen maps. Measures that give consistent scores across an image class and that are sensitive to coding artifacts are …

Siptool: The 'Signal And Image Processing Tool' An Engaging Learning Environment, Fred W. Depiero

Electrical Engineering

The ‘Signal and Image Processing Tool’ is a multimedia software environment for demonstrating and developing Signal & Image Processing techniques. It has been used at Cal Poly for three years. A key feature is extensibility via C/C++ programming. The tool has a minimal learning curve, making it amenable for weekly student projects. The software distribution includes multimedia demonstrations ready for classroom or laboratory use. SIPTool programming assignments strengthen the skills needed for life-long learning by requiring students to translate mathematical expressions into a standard programming language, to create an integrated processing system (as opposed to simply using canned processing routines).