Open Access. Powered by Scholars. Published by Universities.®
- Discipline
Articles 1 - 30 of 61
Full-Text Articles in Physics
Temperature, Rf Field, And Frequency Dependence Performance Evaluation Of Superconducting Niobium Half-Wave Coaxial Cavity, N. K. Raut, G. Ciovati, S. U. De Silva, J. R. Delayen, P. Dhakal, B. D. Khanal, J. K. Tiskumara
Temperature, Rf Field, And Frequency Dependence Performance Evaluation Of Superconducting Niobium Half-Wave Coaxial Cavity, N. K. Raut, G. Ciovati, S. U. De Silva, J. R. Delayen, P. Dhakal, B. D. Khanal, J. K. Tiskumara
Physics Faculty Publications
Recent advancement in superconducting radio frequency cavity processing techniques, with diffusion of impurities within the RF penetration depth, resulted in high quality factor with increase in quality factor with increasing accelerating gradient. The increase in quality factor is the result of a decrease in the surface resistance as a result of nonmagnetic impurities doping and change in electronic density of states. The fundamental understanding of the dependence of surface resistance on frequency and surface preparation is still an active area of research. Here, we present the result of RF measurements of the TEM modes in a coaxial half-wave niobium cavity …
Crab Cavities For Ilc, P. A. Mcintosh, S. A. Belomestnykh, G. Burt, R. Calaga, S. U. De Silva, J. R. Delayen, I. V. Gonin, T. N. Khabiboulline, A. Lunin, T. Okugi, Y. M. Orlov, S. Verdú-Andrés, B. P. Xiao, V. P. Yakovlev, A. Yamamoto
Crab Cavities For Ilc, P. A. Mcintosh, S. A. Belomestnykh, G. Burt, R. Calaga, S. U. De Silva, J. R. Delayen, I. V. Gonin, T. N. Khabiboulline, A. Lunin, T. Okugi, Y. M. Orlov, S. Verdú-Andrés, B. P. Xiao, V. P. Yakovlev, A. Yamamoto
Physics Faculty Publications
For the 14 mrad crossing angle proposed, crab cavity systems are fundamentally anticipated for the viable operation of the International Linear Collider (ILC), in order to maximise its luminosity performance. Since 2021, a specialist development team have been defining optimum crab cavity technologies which can fulfil the operational requirements for ILC, both for its baseline centre-of-mass energy of 250 GeV, but also extending those requirements out to higher beam collision intensities. Five design teams have established crab cavity technology solutions, which have the capability to also operate up to 1 TeV centre-of-mass. This presentation showcases the key performance capabilities of …
Cavity And Cryomodule Developments For Eic, R. A. Rimmer, E. Daly, J. Guo, J. Henry, J. Matalevich, H. Wang, S. Wang, D. Holmes, K. Smith, W. Xu, A. Zaltsman, B. Xiao, Subashini De Silva, Jean R. Delayen
Cavity And Cryomodule Developments For Eic, R. A. Rimmer, E. Daly, J. Guo, J. Henry, J. Matalevich, H. Wang, S. Wang, D. Holmes, K. Smith, W. Xu, A. Zaltsman, B. Xiao, Subashini De Silva, Jean R. Delayen
Physics Faculty Publications
The EIC is a major new project under construction at BNL in partnership with JLab. It relies upon a number of new SRF cavities at 197 MHz, 394 MHz, 591 MHz and 1773 MHz to pre-bunch, accelerate, cool and crab the stored beams. R&D is focusing on the 591 MHz elliptical cavity and 197 MHz crab cavity first as these are the most challenging. Preliminary designs of these cavities are presented along with an R&D status report. To avoid developing multiple different cryostats a modular approach is adopted using a high degree of commonality of parts and systems. This approach …
Eic 197 Mhz Crab Cavity Rf Optimization, Zenghai Li, Subashini U. De Silva, Jean R. Delayen, Robert A. Rimmer, Qiong Wu, Binping Xiao, Wencan Xu
Eic 197 Mhz Crab Cavity Rf Optimization, Zenghai Li, Subashini U. De Silva, Jean R. Delayen, Robert A. Rimmer, Qiong Wu, Binping Xiao, Wencan Xu
Physics Faculty Publications
Crab cavities, operating at 197 MHz and 394 MHz respectively, will be used to compensate the loss of luminosity due to a 25 mrad crossing angle at the interaction point in the Electron Ion Collider (EIC). Both crab cavities are of the RF Dipole (RFD) shape. To meet the machine design requirements, there are a few important cavity design considerations that need to be addressed. First, to achieve stable cavity operation at the design voltages, cavity geometry details must be optimized to suppress potential multipacting. Incorporating strong HOM damping in the cavity design is required for the beam stability and …
Samples For 3rd Harmonic Magnetometry Assessment Of Nbtin-Based Sis Structures, D.R. Beverstock, C.Z. Antoine, Jean R. Delayen, D. Manos, Iresha Harshani Senevirathne, J. K. Spradlin, A-M. Valente-Feliciano
Samples For 3rd Harmonic Magnetometry Assessment Of Nbtin-Based Sis Structures, D.R. Beverstock, C.Z. Antoine, Jean R. Delayen, D. Manos, Iresha Harshani Senevirathne, J. K. Spradlin, A-M. Valente-Feliciano
Physics Faculty Publications
In the quest for alternative superconducting materials to bring accelerator cavity performance beyond the bulk niobium (Nb) intrinsic limits, a promising concept uses superconductor-insulator-superconductor (SIS) thin film structures that allows magnetic flux shielding in accelerator cavities to higher fields [1]. Candidate materials for such structures are NbTiN as the superconductor and AlN as the insulator. We have demonstrated high quality NbTiN and AlN deposited by reactive DC magnetron sputtering (DCMS), both for individual layers and multilayers. Interface quality has been assessed for bilayer stacks with 250 nm NbTiN layers and AlN thicknesses from 30 nm down to1 nm. These SIS …
Bunch Length Measurements At The Cebaf Injector At 130 Kv, Sunil Pokharel, M. W. Bruker, J. M. Grames, A. S. Hofler, R. Kazimi, Geoffrey A. Krafft, S. Zhang
Bunch Length Measurements At The Cebaf Injector At 130 Kv, Sunil Pokharel, M. W. Bruker, J. M. Grames, A. S. Hofler, R. Kazimi, Geoffrey A. Krafft, S. Zhang
Physics Faculty Publications
In this work, we investigated the evolution in bunch length of beams through the CEBAF injector for low to high charge per bunch. Using the General Particle Tracer (GPT), we have simulated the beams through the beamline of the CEBAF injector and analyzed the beam to get the bunch lengths at the location of chopper. We performed these simulations with the existing injector using a 130 kV gun voltage. Finally, we describe measurements to validate these simulations. The measurements have been done using chopper scanning technique for two injector laser drive frequency modes: one with 500 MHz, and another with …
Magnetic Field Mapping Of 1.3 Ghz Superconducting Radio Frequency Niobium Cavities, Ishwari P. Parajuli, Gianluigi Ciovati, Jean R. Delayen, Alex V. Gurevich
Magnetic Field Mapping Of 1.3 Ghz Superconducting Radio Frequency Niobium Cavities, Ishwari P. Parajuli, Gianluigi Ciovati, Jean R. Delayen, Alex V. Gurevich
Physics Faculty Publications
Niobium is the material of choice to build superconducting radio frequency (SRF) cavities, which are fundamental building blocks of modern particle accelerators. These cavities require a cryogenic cool-down to ~2 - 4 K for optimum performance minimizing RF losses on the inner cavity surface. However, temperature-independent residual losses in SRF cavities cannot be prevented entirely. One of the significant contributor to residual losses is trapped magnetic flux. The flux trapping mechanism depends on different factors, such as surface preparations and cool-down conditions. We have developed a diagnostic magnetic field scanning system (MFSS) using Hall probes and anisotropic magneto-resistance sensors to …
Preliminary Results Of Magnetic And Temperature Map System For 3 Ghz Superconducting Radio Frequency Cavities, Ishwari Parajuli, Bashu Khanal, Gianluigi Ciovati, Jean Delayen, Alex Gurevich
Preliminary Results Of Magnetic And Temperature Map System For 3 Ghz Superconducting Radio Frequency Cavities, Ishwari Parajuli, Bashu Khanal, Gianluigi Ciovati, Jean Delayen, Alex Gurevich
Physics Faculty Publications
Superconducting radio frequency (SRF) cavities are fundamental building blocks of modern particle accelerators. When we cool these cavities at cryogenic temperature ~2 – 4 K, we can get optimum performance by minimizing RF losses on the inner cavity surface. However, temperature-independent residual losses in SRF cavities cannot be prevented entirely. One of the leading sources of residual losses in SRF cavities is trapped magnetic flux. The flux trapping mechanism depends on different surface preparations and cool-down conditions. We have designed, developed, and commissioned a combined magnetic (B) and temperature (T) mapping system using anisotropic magneto-resistance (AMR) sensors and carbon resistors …
197 Mhz Waveguide Loaded Crabbing Cavity Design For The Electron-Ion Collider, Subashini De Silva, Jean Delayen, J. Guo, R. A. Rimmer, Z. Li, B. P. Xiao
197 Mhz Waveguide Loaded Crabbing Cavity Design For The Electron-Ion Collider, Subashini De Silva, Jean Delayen, J. Guo, R. A. Rimmer, Z. Li, B. P. Xiao
Physics Faculty Publications
The Electron-Ion Collider will require crabbing systems at both hadron and electron storage rings in order to reach the desired luminosity goal. The 197 MHz crab cavity system is one of the critical rf systems of the collider. The crab cavity, based on the rf-dipole design, explores the option of waveguide load damping to suppress the higher order modes and meet the tight impedance specifications. The cavity is designed with compact dog-bone waveguides with transitions to rectangular wave-guides and waveguide loads. This paper presents the compact 197 MHz crab cavity design with waveguide damping and other ancillaries.
Preliminary Results From Magnetic Field Scanning System For A Single-Cell Niobium Cavity, Ishwari Prasad Parajuli, Gianluigi Ciovati, Jean R. Delayen, Alex V. Gurevich
Preliminary Results From Magnetic Field Scanning System For A Single-Cell Niobium Cavity, Ishwari Prasad Parajuli, Gianluigi Ciovati, Jean R. Delayen, Alex V. Gurevich
Physics Faculty Publications
One of the building blocks of modern particle accelerators is superconducting radiofrequency (SRF) cavities. Niobium is the material of choice to build such cavities, which operate at liquid helium temperature (2 - 4 K) and have some of the highest quality factors found in Nature. There are several sources of residual losses, one of them is trapped magnetic flux, which limits the quality factor in SRF cavities. The flux trapping mechanism depends on different niobium surface preparations and cool-down conditions. Suitable diagnostic tools are not yet available to study the effects of such conditions on magnetic flux trapping. A magnetic …
Field Shielding Of NBT��N Based Multilayer Structure For Accelerating Cavities, Iresha Harshani Senevirathne, Jean R. Delayen, Alex Gurevich, D. R. Beverstock, A.-M. Valente-Feliciano
Field Shielding Of NBT��N Based Multilayer Structure For Accelerating Cavities, Iresha Harshani Senevirathne, Jean R. Delayen, Alex Gurevich, D. R. Beverstock, A.-M. Valente-Feliciano
Physics Faculty Publications
Over the past few decades, bulk niobium (Nb) has been the material of choice for superconducting radio frequency (SRF) cavities used in particle accelerators to achieve higher accelerating gradients and lower RF losses. Multi-layer (SIS) structures consisting of alternating thin layers of superconductor(S) and insulator(I) deposited on a bulk Nb have been proposed to enhance the peak surface magnetic field and sustain a higher accelerating gradient. In this study, multilayers based NbTiN and AlN deposited on bulk Nb are used to test the proposed enhancement using the DC magnetic Hall probe technique. The technique detects a penetrating magnetic field through …
Cooling Performance In A Dual Energy Storage Ring Cooler, B. Dhital, Y. S. Derbenev, D. Douglas, G. A. Krafft, H. Zhang, F. Lin, V. S. Morozov, Y. Zhang
Cooling Performance In A Dual Energy Storage Ring Cooler, B. Dhital, Y. S. Derbenev, D. Douglas, G. A. Krafft, H. Zhang, F. Lin, V. S. Morozov, Y. Zhang
Physics Faculty Publications
The longitudinal and transverse emittance growth in hadron beams due to intra-beam scattering (IBS) and other heating sources deteriorate the luminosity in a collider. Hence, a strong hadron beam cooling is required to reduce and preserve the emittance. The cooling of high energy hadron beam is challenging. We propose a dual energy storage ring-based electron cooler that uses an electron beam to extract heat away from hadron beam in the cooler ring while the electron beam is cooled by synchrotron radiation damping in the high energy damping ring. In this paper, we present a design of a dual energy storage …
Modeling A Nb3Sn Cryounit In Gpt In Uitf, Sunil Pokharel, Geoffey A. Krafft, A. S. Hofler
Modeling A Nb3Sn Cryounit In Gpt In Uitf, Sunil Pokharel, Geoffey A. Krafft, A. S. Hofler
Physics Faculty Publications
Nb₃Sn is a prospective material for future superconducting RF (SRF) accelerator cavities. The material can achieve higher quality factors, higher temperature operation and potentially higher accelerating gradients (E_{acc} 96 MV/m) compared to conventional niobium. In this work, we performed modeling of the Upgraded Injector Test Facility (UITF) at Jefferson Lab utilizing newly constructed Nb₃Sn cavities. We studied the effects of the buncher cavity and varied the gun voltages from 200-500 keV. We have calibrated and optimized the SRF cavity gradients and phases for the Nb₃Sn five-cell cavities energy gains with the framework of General Particle Tracer (GPT). Our calculations show …
Evaluation Of Single-Cell Cavities Made Of Forged Ingot Niobium At Jefferson Lab, P. Dhakal, Bashu D. Khanal, Gianluigi Ciovati, G. R. Myneni
Evaluation Of Single-Cell Cavities Made Of Forged Ingot Niobium At Jefferson Lab, P. Dhakal, Bashu D. Khanal, Gianluigi Ciovati, G. R. Myneni
Physics Faculty Publications
Currently, fine grain niobium (Nb) (grain size ∼ 50 µm) and large grain Nb (grain size of a few cm) are being used for the fabrication of superconducting radio frequency (SRF) cavities. Medium grain forged ingot with grain size of a few hundred µm may be beneficial for cost-effectiveness as well as providing better performance for future SRF-based accelerators. Forged ingot Nb with medium grain size is a novel production method to obtain Nb discs used for the fabrication of superconducting radio frequency cavities. We have fabricated two 1.5 GHz single cell cavities made from forged Nb ingot with a …
Magnetic Flux Expulsion In Superconducting Radio-Frequency Niobium Cavities Made From Cold Worked Niobium, Bashu D. Khanal, S. Balachandran, S. Chetri, P. J. Lee, P. Dhakal
Magnetic Flux Expulsion In Superconducting Radio-Frequency Niobium Cavities Made From Cold Worked Niobium, Bashu D. Khanal, S. Balachandran, S. Chetri, P. J. Lee, P. Dhakal
Physics Faculty Publications
Trapped residual magnetic field during the cooldown of superconducting radio frequency (SRF) cavities is one of the primary source of RF residual losses leading to lower quality factor. Historically, SRF cavities have been fabricated from high purity fine grain niobium with grain size ~50 - 100 μm as well as large grain with grain size of the order of few centimeters. Non-uniform recrystallization of fine-grain Nb cavities after the post fabrication heat treatment leads to higher flux trapping during cooldown, hence the lower quality factor. We fabricated two 1.3 GHz single cell cavities from cold-worked niobium from different vendors and …
Lower Temperature Annealing Of Vapor Diffused Nb3Sn For Accelerator Cavities, Jayendrika K. Tiskumara, Jean R. Delayen, G. V. Eremeev, U. Pudasaini
Lower Temperature Annealing Of Vapor Diffused Nb3Sn For Accelerator Cavities, Jayendrika K. Tiskumara, Jean R. Delayen, G. V. Eremeev, U. Pudasaini
Physics Faculty Publications
Nb3Sn is a next-generation superconducting material for the accelerator cavities with higher critical temperature and superheating field, both twice compared to Nb. It promises superior performance and higher operating temperature than Nb, resulting in significant cost reduction. So far, the Sn vapor diffusion method is the most preferred and successful technique to coat niobium cavities with Nb3Sn. Although several post-coating techniques (chemical, electrochemical, mechanical) have been explored to improve the surface quality of the coated surface, an effective process has yet to be found. Since there are only a few studies on the post-coating heat treatment …
Nb3Sn Coating Of Twin Axis Cavity For Accelerator Applications, Jayendrika K. Tiskumara, Subashini U. De Silva, Jean Delayen, U. Pudasaini, C. E. Reece, H. Park, G. Eremeev
Nb3Sn Coating Of Twin Axis Cavity For Accelerator Applications, Jayendrika K. Tiskumara, Subashini U. De Silva, Jean Delayen, U. Pudasaini, C. E. Reece, H. Park, G. Eremeev
Physics Faculty Publications
A Superconducting twin axis cavity consisting of two identical beam pipes that can accelerate and decelerate beams within the same structure has been proposed for the Energy Recovery Linac (ERL) applications. There are two niobium twin axis cavities at JLab fabricated with the intention of later Nb₃Sn coating and now we are progressing to coat them using vapor diffusion method. Nb₃Sn is a potential alternate material for replacing Nb in SRF cavities for better performance and reducing operational costs. Because of advanced geometry, larger surface area, increased number of ports and hard to reach areas of the twin axis cavities, …
Eic Crab Cavity Multipole Analysis, Q. Wu, Y. Luo, B. Xiao, Subashini De Silva, J. A. Mitchell
Eic Crab Cavity Multipole Analysis, Q. Wu, Y. Luo, B. Xiao, Subashini De Silva, J. A. Mitchell
Physics Faculty Publications
Crab cavities are specialized RF devices designed for colliders targeting high luminosities. It is a straightforward solution to retrieve head-on collision with crossing angle existing to fast separate both beams after collision. The Electron Ion Collider (EIC) has a crossing angle of 25 mrad, and will use local crabbing to minimize the dynamic aperture requirement throughout the rings. The current crab cavity design for the EIC lacks axial symmetry. Therefore, their higher order components of the fundamental deflecting mode have a potential of affecting the long-term beam stability. We present here the multipole analysis and preliminary particle tracking results from …
Design Of An Rf-Dipole Crabbing Cavity System For The Electron-Ion Collider, Subashini U. De Silva, Jean R. Delayen, H. Park, F. Marhauser, J. Henry, R. A. Rimmer
Design Of An Rf-Dipole Crabbing Cavity System For The Electron-Ion Collider, Subashini U. De Silva, Jean R. Delayen, H. Park, F. Marhauser, J. Henry, R. A. Rimmer
Physics Faculty Publications
The Electron-Ion Collider requires several crabbing systems to facilitate head-on collisions between electron and proton beams in increasing the luminosity at the interaction point. One of the critical rf systems is the 197 MHz crabbing system that will be used in crabbing the proton beam. Many factors such as the low operating frequency, large transverse voltage requirement, tight longitudinal and transverse impedance thresholds, and limited beam line space makes the crabbing cavity design challenging. The rf-dipole cavity design is considered as one of the crabbing cavity options for the 197 MHz crabbing system. The cavity is designed including the HOM …
Beam Dynamics Study In A Dual Energy Storage Ring For Ion Beam Cooling*, B. Dhital, Y. S. Derbenev, D. Douglas, A. Hutton, Geoffrey A. Krafft, F. Lin, V. S. Morozov, Y. Zhang
Beam Dynamics Study In A Dual Energy Storage Ring For Ion Beam Cooling*, B. Dhital, Y. S. Derbenev, D. Douglas, A. Hutton, Geoffrey A. Krafft, F. Lin, V. S. Morozov, Y. Zhang
Physics Faculty Publications
A dual energy storage ring designed for beam cooling consists of two closed rings with significantly different energies: the cooling and damping rings. These two rings are connected by an energy recovering superconducting RF structure that provides the necessary energy difference. In our design, the RF acceleration has a main linac and harmonic cavities both running at crest that at first accelerates the beam from low energy E_{L} to high energy E_{H} and then decelerates the beam from E_{H} to E_{L} in the next pass. The purpose of the harmonic cavities is to extend the bunch length in a dual …
Nb3Sn Coating Of Twin Axis Cavity For Srf Applications, J. K. Tiskumara, Jean R. Delayen, G. V. Eremeev, U. Pudasaini, C. E. Reece
Nb3Sn Coating Of Twin Axis Cavity For Srf Applications, J. K. Tiskumara, Jean R. Delayen, G. V. Eremeev, U. Pudasaini, C. E. Reece
Physics Faculty Publications
The twin axis cavity with two identical accelerating beams has been proposed for energy recovery linac (ERL) applications. Nb3Sn is a superconducting material with a higher critical temperature and a higher critical field as compared to Nb, which promises a lower operating cost due to higher quality factors. Two niobium twin axis cavities were fabricated at JLab and were proposed to be coated with Nb3Sn. Due to their more complex geometry, the typical coating process used for basic elliptical cavi-ties needs to be improved to coat these cavities. This development advances the current coating system at …
Overview Of Srf Deflecting And Crabbing Cavities, Subashini De Silva
Overview Of Srf Deflecting And Crabbing Cavities, Subashini De Silva
Physics Faculty Publications
Developments over the past few years on novel superconducting deflecting and crabbing cavities have introduced advanced rf geometries with improved performance, in comparison to the typical squashed elliptical cavities operating in TM110 type mode. These new structures are compact geometries operating in either TEM type or TE11-like mode. One of the key applications of such cavities is the use of crabbing systems for circular colliders in increasing the luminosity. Crabbing systems are an essential component in future colliders with intense beams and proposed electron-ion colliders. High luminosity upgrade of LHC is planned to implement crabbing systems at two interaction points. …
Analysis Of Higher Order Multipoles Of The 952.6 Mhz Rf-Dipole Crabbing Cavity For The Jefferson Lab Electron Ion Collider, Subashini U. De Silva, J. R. Delayen, V. S. Morozov, H. Park, S. Sosa
Analysis Of Higher Order Multipoles Of The 952.6 Mhz Rf-Dipole Crabbing Cavity For The Jefferson Lab Electron Ion Collider, Subashini U. De Silva, J. R. Delayen, V. S. Morozov, H. Park, S. Sosa
Physics Faculty Publications
The crabbing system is a key feature in the Jefferson Lab Electron-Ion Collider (JLEIC) required to increase the luminosity of the colliding bunches. A local crabbing system will be installed with superconducting rf-dipole crabbing cavities operating at 952.6 MHz. The field non-uniformity across the beam aperture in the crabbing cavities produces higher order multipole components, similar to that which are present in magnets. Knowledge of higher order mode multipole field effects is important for accurate beam dynamics study for the crabbing system. In this paper, we quantify the multipole components and analyse their effects on the beam dynamics.
Simulation And Measurements Of Hom Filter Of The Larp Prototype Rf-Dipole Crabbing Cavity Using An Rf Test Box, Subashini U. De Silva, Jean R. Delayen, Z. Li
Simulation And Measurements Of Hom Filter Of The Larp Prototype Rf-Dipole Crabbing Cavity Using An Rf Test Box, Subashini U. De Silva, Jean R. Delayen, Z. Li
Physics Faculty Publications
The RF-Dipole Crabbing Cavity designed for the LHC High Luminosity Upgrade includes two higher order mode (HOM) couplers. One of the HOM couplers is an rf filter, which is a high pass filter designed to couple to the horizontal dipole modes and accelerating modes up to 2 GHz, while rejecting the fundamental operating mode at 400 MHz. The coupler consists of a high pass filter circuit where the rejection of the operating mode and transmission of HOMs are sensitive to dimensional deviations. An rf test box has been designed to measure the transmission of the rf filter in order to …
Measurement Of The Magnetic Field Penetration Into Superconducting Thin Films, Iresha Harshani Senevirathne, Gianluigi Ciovati, Jean R. Delayen
Measurement Of The Magnetic Field Penetration Into Superconducting Thin Films, Iresha Harshani Senevirathne, Gianluigi Ciovati, Jean R. Delayen
Physics Faculty Publications
The magnetic field at which first flux penetrates is a fundamental parameter characterizing superconducting materials for SRF cavities. Therefore, an accurate technique is needed to measure the penetration of the magnetic field directly. The conventional magnetometers are inconvenient for thin superconducting film measurements because these measurements are strongly influenced by orientation, edge and shape effects. In order to measure the onset of field penetration in bulk, thin films and multi-layered superconductors, we have designed, built and calibrated a system combining a small superconducting solenoid capable of generating surface magnetic field higher than 500 mT and Hall probe to detect the …
Design And Commissioning Of A Magnetic Field Scanning System For Srf Cavities, Ishwari Prasad Parajuli, Gianluigi Ciovati, W. A. Clemens, Jean R. Delayen, J. Nice, Alex V. Gurevich
Design And Commissioning Of A Magnetic Field Scanning System For Srf Cavities, Ishwari Prasad Parajuli, Gianluigi Ciovati, W. A. Clemens, Jean R. Delayen, J. Nice, Alex V. Gurevich
Physics Faculty Publications
Trapped magnetic vortices are one of the leading sources of residual losses in SRF cavities. Mechanisms of flux pinning depend on the materials treatment and cool-down conditions. A magnetic field scanning system using flux-gate magnetometers and Hall probes has been designed and built to allow measuring the local magnetic field of trapped vortices normal to the outer surface of 1.3 GHz single-cell SRF cavities at cryogenic temperatures. Such system will allow inferring the key information about the distribution and magnitude of trapped flux in the SRF cavities for different material, surface preparations and cool-down conditions.
Two-Energy Storage-Ring Electron Cooler For Relativistic Ion Beams, Bhawin Dhital, Jean R. Delayen, Y. S. Derbenev, D. Douglas, Geoffrey A. Krafft, F. Lin, V. S. Morozov, Y. Zhang
Two-Energy Storage-Ring Electron Cooler For Relativistic Ion Beams, Bhawin Dhital, Jean R. Delayen, Y. S. Derbenev, D. Douglas, Geoffrey A. Krafft, F. Lin, V. S. Morozov, Y. Zhang
Physics Faculty Publications
An electron beam based cooling system for the ion beam is one of the commonly used approaches. The proposed two’energy storage-ring electron cooler consists of damping and cooling sections at markedly different energies connected by an energy recovering superconducting RF structure. The parameters in the cooling and damping sections are adjusted for optimum cooling of a stored ion beam and for optimum damping of the electron beam respectively. This paper briefly describes a two cavities model along with a third cavity model to accelerate and decelerate the electron beam in two energy storage ring. Based on our assumed value of …
Beam-Beam Effect: Crab Dynamics Calculation In Jleic, He Huang, Vasiliy Morozov, Yves Roblin, Amy Sy, Fanglei Lin, Yuhong Zhang, Balša Terzić, Salvador Sosa, Isurumali Neththikumara
Beam-Beam Effect: Crab Dynamics Calculation In Jleic, He Huang, Vasiliy Morozov, Yves Roblin, Amy Sy, Fanglei Lin, Yuhong Zhang, Balša Terzić, Salvador Sosa, Isurumali Neththikumara
Physics Faculty Publications
The electron and ion beams of a future Electron Ion Collider (EIC) must collide at an angle for detection, machine and engineering design reasons. To avoid associated luminosity reduction, a local crabbing scheme is used where each beam is crabbed before collision and de-crabbed after collision. The crab crossing scheme then provides a head-on collision for beams with a non-zero crossing angle. We develop a framework for accurate simulation of crabbing dynamics with beam-beam effects by combining symplectic particle tracking codes with a beam-beam model based on the Bassetti-Erskine analytic solution. We present simulation results using our implementation of such …
Measurement Of Surface Resistance Properties With Coaxial Resonators - Review, Hyekyoung Park, Subashini De Silva, J. R. Delayen
Measurement Of Surface Resistance Properties With Coaxial Resonators - Review, Hyekyoung Park, Subashini De Silva, J. R. Delayen
Physics Faculty Publications
Achieving ever decreasing surface resistance at higher field in superconducting RF accelerating structures is one of most outstanding developments in modern accelerators. The BCS theory has been used widely to estimate the surface resistance and to direct the technology. However, recent research results show that the behavior of the surface resistance further deviates from the BCS theory. So far the study on surface resistance was performed usually with cavities of single frequency which limited the study of frequency dependent surface resistance. The Center for Accelerator Science at Old Dominion University has designed and built several half wave coaxial cavities to …
Design Of A Proof-Of-Principle Crabbing Cavity For The Jefferson Lab Electron-Ion Collider, Hyekyoung Park, Subashini U. De Silva, Salvador I. Sosa Guitron, Jean R. Delayen
Design Of A Proof-Of-Principle Crabbing Cavity For The Jefferson Lab Electron-Ion Collider, Hyekyoung Park, Subashini U. De Silva, Salvador I. Sosa Guitron, Jean R. Delayen
Physics Faculty Publications
The Jefferson Lab design for an electron-ion collider (JLEIC) requires crabbing of the electron and ion beams in order to achieve the design luminosity. A number of options for the crabbing cavities have been explored, and the one which has been selected for the proof-of-principle is a 952 MHz, 2-cell rf-dipole (RFD) cavity. This paper summarizes the electromagnetic design of the cavity and its HOM characteristics.