Physics Commons^™

Chaotic Free-Space Laser Communication Over Turbulent Channel, N. F. Rulkov, Mikhail Vorontsov, L. Illing

Electro-Optics and Photonics Faculty Publications

The dynamics of errors caused by atmospheric turbulence in a self-synchronizing chaos-based communication system that stably transmits information over a ∼5  km free-space laser link is studied experimentally. Binary information is transmitted using a chaotic sequence of short-term pulses as a carrier. The information signal slightly shifts the chaotic time position of each pulse depending on the information bit. We report the results of an experimental analysis of the atmospheric turbulence in the channel and the impact of turbulence on the bit-error-rate performance of this chaos-based communication system.

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report August September October 2002, John Farley

Transmutation Sciences Materials (TRP)

We continued with sputter depth profiling of 316 and 316L steel samples that have been exposed to LBE. We also calibrated the sputter depth profiling using a sample of SiO₂ on Si, and the SEM. This is a valuable independent determination of the thickness of oxide layers.

In the laboratory, progress continues using the XPS machine. Experiments have been performed on steel samples using Argon ions to mill away the surface of the sample, thereby making measurements as a function of depth. This "ion beam milling" proceeds slowly through the oxide layer that covers the steel sample. We are …

University Of Nevada, Las Vegas Advanced Accelerator Applications University Participation Program: Quarterly Report, First Quarter Year 2 (March 2002 To May 2002), Anthony Hechanova

Transmutation Research Program Reports (TRP)

This Quarterly Report is a primary deliverable from the University of Nevada, Las Vegas (UNLV) Advanced Accelerator Applications (AAA) University Participation Program (UPP) Director to the U.S. Department of Energy (DOE) as described in the UNLV AAA proposal, and Statement of Work for the First Quarter Year 2 and AAA FY02 Work Package.

The UNLV AAA UPP Director implements the program’s administration using staff from the Harry Reid Center for Environmental Studies (HRC) to ensure that work conducted under the UNLV AAA UPP meets program objectives. The UNLV AAA program consists of four components: Program Support, Research Infrastructure Augmentation, International …

University Of Nevada, Las Vegas Advanced Accelerator Applications University Participation Program: Quarterly Report, Third Quarter Year 2 (Sept. 2002 To Nov. 2002), Anthony Hechanova

Transmutation Research Program Reports (TRP)

This Quarterly Report is a primary deliverable from the University of Nevada, Las Vegas (UNLV) Advanced Accelerator Applications (AAA) University Participation Program (UPP) Director to the U.S. Department of Energy (DOE) as described in the UNLV AAA proposal and Statement of Work for the Fourth Quarter.

The UNLV AAA UPP Director implements the program’s administration using staff from the Harry Reid Center for Environmental Studies (HRC) to ensure that work conducted under the UNLV AAA UPP meets program objectives. The UNLV AAA program consists of three components: Program Support, Research Infrastructure Augmentation, and Student Research.

Dielectric Properties Of A Ferroelectric Copolymer Langmuir–Blodgett Film, Mahantappa S. Jogad, Stephen Ducharme

Stephen Ducharme Publications

We report measurements of the real (epsilon prime) and imaginary (epsilon double-prime) parts of the relative complex permittivity of a Langmuir–Blodgett film of ferroelectric copolymer of vinylidene fluoride (70%) with trifluoroethylene (30%). The measurements were made in the temperature range of 35 to 125° C, and frequency range of 19 Hz to 5 MHz. The results indicate low frequency loss due to conduction and dielectric loss peak near the ferroelectric–paraelectric phase transition.

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 5/16/02- 8/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

An important aspect of the Advanced Accelerator Applications (AAA) program is the development of a casting process by which volatile actinide element (i.e., americium) can be incorporated into metallic alloy fuel pins. The traditional metal fuel casting process uses an inductively heated crucible.

This process works well for the fabrication of metal fuel pins traditionally composed of alloys of uranium and plutonium, but does not work well when highly volatile actinides are included in the melt. The problem occurs both during the extended time period required to superheat the alloy melt as well as when the chamber must be evacuated. …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report For May-June-July 2002, John Farley

Transmutation Sciences Materials (TRP)

The goal of this project is to understand the basic science of corrosion in the steel/LBE system.

We are taking more data, typically using the newly installed X-ray Photoelectron Spectrometry (XPS) apparatus, and analyzing our existing data. Undergraduate students Denise Parsons and Julia Manzerova have helped a great deal in the analysis of the data. We can obtain the elemental composition as a function of position within the sample. This gives clues to the migration of materials, the composition of the protective oxide layer, and the basic science of the corrosion process. We found dramatic differences between the exposed and …

Phase I: Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

The proposed research would be conducted in 3 phases. Each of the phases would be carried out over a one-year period. Phase I includes model development, analysis, and the selection of a new casting furnace design. The work discussed in this report was completed as Phase I. Phase II of the program will lead to more modeling and validation to evaluate the proposed furnace concept. Phase III would be a joint effort between UNLV and Argonne National Laboratory (ANL) to demonstrate the acceptable use of the new furnace in a simulated remote environment.

The Phase III work would include the …

Development Of A Model For Induction Heating, Randy Clarksean, Yitung Chen

Fuels Campaign (TRP)

There are two coupled equations that must be solved in order to determine the power deposition. The numerical solution of these equations is needed in order to apply a source term within the energy equations. These equations have previously solved in FIDAP. That implementation used modified versions of the momentum and energy equations to provide a mechanism for the solution of two coupled equations. Currently, we want to solve for the induction heating field in addition to the flow field and the energy equation. In order to do this, a mechanism has to be defined within FIDAP to solve these …

Cuin1-Xalxse2 Thin Films And Solar Cells, P. D. Paulson, M. W. Haimbodi, S. Marsillac, R. W. Birkmire, W. N. Shafarman

Electrical & Computer Engineering Faculty Publications

CuIn[sub 1-x]Al[sub x]Se[sub 2] thin films are investigated for their application as the absorber layer material for high efficiency solar cells. Single-phase CuIn[sub 1-x]Al[sub x]Se[sub 2] films were deposited by four source elemental evaporation with a composition range of 0≤x≤0.6. All these films demonstrate a normalized subband gap transmission >85% with 2 µm film thickness. Band gaps obtained from spectroscopic ellipsometry show an increase with the Al content in the CuIn[sub 1-x]Al[sub x]Se[sub 2] film with a bowing parameter of 0.62. The structural properties investigated using x-ray diffraction measurements show a decrease in lattice spacing as the Al content increases. …

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The objective of this project is the design and evaluation of manufacturing processes for transmuter fuel fabrication. The large-scale deployment of remote fabrication and refabrication processes will be required for all transmutation scenarios. Current program emphasis is on a five-year effort to determine the feasibility of transmutation as a technology to limit the need for repository storage of spent commercial fuel. The evaluation of the fabrication processes will create a decision support data base to document design, operations, and costs. Fabrication processes required for different fuel types differ in terms of equipment types, throughput, and cost. Differential cost Implications of …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #3, Georg F. Mauer

Fuels Campaign (TRP)

The third quarter of the project covered the following:

• Literature Search: The process of evaluating the pertinent literature continued. Results are summarized.

• Mr. Richard Silva, developed an initial work cell simulation with two robots. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project. Rich is employed with Bechtel at the Yucca Mountain project.

• The equipment detail and estimates were refined based on the literature survey results for different manufacturing plant design options.

• Concepts and Methods for Vision-Based Hot Cell Supervision and control (Ph.D. Student Jae-Kyu Lee )

Structure And Magnetic Properties Of The Mnbi Low Temperature Phase, Jinbo Yang, William B. Yelon, William Joseph James, Qingsheng Cai, Samit Roy, Naushad Ali

Physics Faculty Research & Creative Works

High purity MnBi low temperature phase has been prepared and analyzed using magnetic measurements and neutron diffraction. The low-temperature phase of the MnBi alloy has a coercivity μ_0iH_c of 2.0 T at 400 K, and exhibits a positive temperature coefficient from 0 to at least 400 K. The neutron data refinement indicated that the Mn atom changes its spin direction from c axis above room temperature to nearly perpendicular to the c axis at 50 K. A canted magnetic structure has been observed below 200 K. The anisotropy field increases with increasing temperature which gives rise to …

Magnetic And Mössbauer Studies On Oxygen Deficient Perovskite, La₀.₆Sr₀.₄Feo3-Δ, Jinbo Yang, William B. Yelon, William Joseph James, X.-D. Zhou, Yixiang Xie, Harlan U. Anderson, Zili Chu

Physics Faculty Research & Creative Works

Samples of La_0.6Sr_0.4Fe_3-δ with varying oxygen vacancy contents were prepared by heating them in different gas flows. Magnetization measurement showed that samples with low oxygen vacancies have a magnetic ordering temperature in the range of 300-325 K while those with 9%-12% oxygen vacancies have a magnetic ordering temperature of 800 K and higher. Mössbauer spectra at 300 K exhibit paramagnetic or weak magnetic characteristics for the N₂, O₂, and air-quenched samples, whereas an average hyperfine field of 52 T is found for the CO/CO₂ reduced samples. The heat treatment in …

Humidity And Temperature Boundaries For Biofilm Formation In Yucca Mountain, Terry Ann Else, Penny S. Amy, James Jay, Amy J. Smiecinski

Publications (YM)

To determine the long-term success of the recommended Yucca Mountain high-level nuclear waste repository, studies of bacterial colonization and biofilm development are needed. Bacteria involved in microbially-influenced corrosion and degradation are known to form biofilms with the potential to impact the integrity of repository packaging and structural materials. Temperature and humidity are environmental factors that can greatly affect biofilm formation. Therefore, it is necessary to determine the temperature and humidity conditions that affect biofilm formation. Microcosms, which simulated the repository environment of Yucca Mountain, were placed at temperatures ranging from 30° C to 70° C and in relative humidities ranging …

The Fission Properties Of Curium Separated From Spent Nuclear Fuel, William Culbreth, Elizabeth Bakker, Jason Viggato

Separations Campaign (TRP)

Curium poses special problems in the chemical preparation of spent nuclear fuel for transmutation. Once separated from the other minor actinides, the seven curium isotopes in spent fuel can lead to nuclear fission with the subsequent release of a large amount of radiation. Several isotopes of curium also generate a significant amount of heat by radioactive decay. Sustained fission can be avoided by preventing the accumulation by more that a critical mass of curium. The heat generation of curium presents even more restriction on the mass of curium that can safely be contained in one location.

To analyze the nuclear …

Nuclear Criticality Analyses Of Separations Processes For The Transmutation Fuel Cycle: Quarterly Report, William Culbreth, Pang Tao

Separations Campaign (TRP)

During the first two quarters of the work, the tasks included training students in the use of Monte Carlo codes used in radiation transport studies and the assessment of neutron multiplication factors for specific problems outlined by ANL-East through Drs. Laidler and Vandegrift.

The proposal also included objectives for the first year of work on this project, as listed below. The work conducted in the second quarter of the project was in partial completion of these objectives.

• Train UNLV students in the use of SCALE and/or MCNP for the assessment of nuclear criticality.

• Assess neutron multiplication factor, k …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to ensure that their knowledge and experience benefits the project. The research to be conducted during the second year will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this second year is …

University Of Nevada, Las Vegas Advanced Accelerator Applications University Participation Program: Quarterly Report Fourth Quarter (December 2001 To February 2002), Anthony Hechanova

Transmutation Research Program Reports (TRP)

This Quarterly Report is a primary deliverable from the University of Nevada, Las Vegas (UNLV) Advanced Accelerator Applications (AAA) University Participation Program (UPP) Director to the U.S. Department of Energy (DOE) as described in the UNLV AAA proposal and Statement of Work for the Fourth Quarter.

The UNLV AAA UPP Director implements the program’s administration using staff from the Harry Reid Center for Environmental Studies (HRC) to ensure that work conducted under the UNLV AAA UPP meets program objectives. The UNLV AAA program consists of three components: Program Support, Research Infrastructure Augmentation, and Student Research.

Third Quarter Report, Covering January Through March 2002, John Farley

Transmutation Sciences Materials (TRP)

Progress from June 2001-November 2001 was presented at the winter meeting of the American Nuclear Society in Reno (November 12-15, 2001), and incorporated into a refereed conference proceeding. A copy of the refereed conference proceeding has been provided to Tony Hechanova. In brief, the paper described the new program to examine the corrosive effects of lead-bismuth eutectic (LBE) on steels. We employed various types of surface studies (Scanning Electron Microscope [SEM], and X-ray Photoelectron Spectrometry [XPS]) to examine steel samples that had been exposed to LBE for various lengths of time at various temperatures. The goal is to understand the …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #2, Georg F. Mauer

Fuels Campaign (TRP)

The second quarter of the project covered the following:

• Project review with Dr. Mitchell Meyer, ANL West: A project review of the transmuter fuels project was conducted during the January 2002 AAA meeting in Las Vegas.

• A second graduate student, Mr. Richard Silva, began working on the project. Rich will develop detailed 3-D process simulation models as his M.Sc. thesis project. Rich is employed with Bechtel at the Yucca Mountain project.

• AAA Seminar Presentation by Mr. Jae-Kyu Lee and G. Mauer. Title: Transmuter Fuel Fabrication Processes.

• More equipment detail and estimates were developed for different manufacturing …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 11/16/01- 2/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

An important aspect of the Advanced Accelerator Applications (AAA) program is the development of a casting process by which volatile actinide element (i.e., americium) can be incorporated into metallic alloy fuel pins. The traditional metal fuel casting process uses an inductively heated crucible.

This process works well for the fabrication of metal fuel pins traditionally composed of alloys of uranium and plutonium, but does not work well when highly volatile actinides are included in the melt. The problem occurs both during the extended time period required to superheat the alloy melt as well as when the chamber must be evacuated. …

Radiation Resistance Testing Of Mosfet And Cmos As A Means Of Risk Management, Akira Tokuhiro, Massimo F. Bertino

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

Whether for military, research (space, accelerator physics) and/or civilian use, risk avoidance against radiation-induced damage is not possible with COTS parts. Thus the sensible approach is risk management. We recommend a sensible risk management approach as follows: 1) know the radiation environment of the intended application to the extent possible; 2) know the effects of ionizing radiation on the component(s) of interest; 3) know the requirements of the application; 4) identify the candidate or chosen components; 5) test the components; 6) design-in safety factor margins to the extent possible.

Atmospheric Turbulence Conditions Leading To Focused And Folded Sonic Boom Wave Fronts, Andrew A. Piacsek

All Faculty Scholarship for the College of the Sciences

The propagation and subsequent distortion of sonic booms with rippled wave fronts are investigated theoretically using a nonlinear time-domain finite-difference scheme. This work seeks to validate the rippled wave front approach as a method for explaining the significant effects of turbulence on sonic booms [A. S. Pierce and D. J. Maglieri, J. Acoust. Soc. Am. 51, 702–721 (1971)]. A very simple description of turbulence is employed in which velocity perturbations within a shallow layer of the atmosphere form strings of vortices characterized by their size and speed. Passage of a steady-state plane shock front through such a vortex layer …

Thermoelectric Properties Of Bi2sr2co2o9 Whiskers Under Hydrostatic Pressure, F Chen, Kevin L. Stokes, Ryozi Funahashi

Physics Faculty Publications

We report the temperature dependence of thermopower (S) in the ab plane of Bi2Sr2Co2O9 {BC-222} single crystalline whiskers under high pressure up to 1.2 GPa. Special modifications were made to our high-pressure transport measurement system to improve the measurement accuracy of S for whiskers with high resistance. Pressure improved the contact resistance dramatically. We observed a slight decrease of S and four-wire electrical conductivity (sigma) under high pressure. As a result, the power factor (S2sigma) was decreased less than 20% by pressure. From the temperature dependence of sigma, the band gap of BC-222 whiskers increase very slightly …

Synthesis And Magnetic Properties Of Copt–Poly(Methylmethacrylate) Nanostructured Composite Material, Jiye Fang, Kevin L. Stokes, Jibao He, Weillie L. Zhou, Charles J. O'Connor, Daniela Caruntu

Physics Faculty Publications

We have prepared nanometer-sized CoPt particles dispersed in a poly~methyl methacrylate~PMMA!matrix, as a novel nanostructured magnetic plastic, through a soft chemical processing route. In this work, CoPt nanoparticles were successfully synthesized from a solution phase reduction system in the presence of capping ligands and stabilizing agents at high temperature. The CoPt nanoparticles were annealed at 400 °C for 3 h, and were subsequently re-dispersed inmethylmethacrylate~monomer! . The polymerization was induced by a UV source and the hardness of final product was adjusted by varying the amount of monomeric cross-link agent. Annealed bare CoPt nanoparticles as a ‘‘core’’ material and CoPt–PMMA …

Effect Of Ga Content On Defect States In Cuin1-XGaXSe2 Photovoltaic Devices, Jennifer T. Heath, J. David Cohen, William N. Shafarman, Dongxiang Liao, Angus Rockett

Faculty Publications

Defects in the band gap of CuIn_1-xGa_xSe₂ have been characterized using transient photocapacitance spectroscopy. The measured spectra clearly show response from a band of defects centered around 0.8 eV from the valence band edge as well as an exponential distribution of band tail states. Despite Ga contents ranging from Ga/(In+Ga)=0.0 to 0.8, the defect bandwidth and its position relative to the valence band remain constant. This defect band may act as an important recombination center, contributing to the decrease in device efficiency with increasing Ga content.

Nuclear Criticality Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Pang Tao, Denis Beller

Separations Campaign (TRP)

The separation and partitioning of used commercial reactor fuel is a vital component of any reprocessing or transmutation strategy. To process the high actinide fuels required for a transmutation effort, the Chemical Technology Division (CMT) at Argonne National Laboratory (ANL) is developing a pyrochemical separations process. Currently, this work is being done via small experiments. While this is more than sufficient to develop the technologies required to process actinide-bearing fuels, it does not allow for the direct investigation of criticality concerns that would be present in larger systems. As the volume of waste to be treated increases, a higher probability …

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Denis Beller

Separations Campaign (TRP)

The remediation of nuclear waste created by conventional fission reactors will rely upon the separation of the waste products for further treatment. The UREX+ process now under review will involve the use of an aqueous chemical process to separate out depleted uranium resulting in a product containing minor actinides, fission products, cesium, strontium, technetium, and iodine. The radioactive decay of strontium and cesium produces roughly half of the thermal and gamma production in spent fuel and the relatively short halflife of isotopes of both of these elements requires storage for about 300 years before heat and radiation decreases to safe …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Carter D. Hull, William H. Johnson

Transmutation Sciences Physics (TRP)

To begin developing the database necessary for the validation and benchmarking of the LAHET component of the MCNPX code suite, the UNLV research program has set forth the following objectives. First, the current MCNPX suite will be used to develop models of multi-element neutron detector systems. These models of the detector systems will be incorporated into the design of detailed models for the entire detector-target system. These models will first be used to help design the irradiation experiments, and then will be used to model the behavior of the system. Irradiation experiments corresponding to the detector-target system models will be …