Physics Commons^™

Measurements Of Magnetic Field Penetration Of Materials For Superconducting Radiofrequency Cavities, Iresha Harshani Senevirathne

Physics Theses & Dissertations

Superconducting Radio Frequency (SRF) cavities used in particle accelerators are typically formed from or coated with superconducting materials. Currently high purity niobium is the material of choice for SRF cavities which have been optimized to operate near their theoretical field limits. This brings about the need for significant R&D efforts to develop next generation superconducting materials which could outperform Nb and keep up with the demands of new accelerator facilities. To achieve high quality factors and accelerating gradients, the cavity material should be able to remain in the superconducting Meissner state under high RF magnetic field without penetration of quantized …

Nb3Sn Coating Of Twin Axis Cavity And Other Complex Srf Cavity Structures, Jayendrika Kumari Tiskumara

Physics Theses & Dissertations

In the field of Accelerator Science, for the low cost and increased quality factor, thin films coated niobium cavities are used in the modern SRF research. Within the potential substances, Nb₃Sn has shown higher critical temperature than niobium. Here the tin vapor diffusion method is used as the preferred technique to coat niobium cavities. So far, only elliptical cavities have been coated with Nb₃Sn and this technique has not yet been applied to cavities with complex geometries, which are also helpful in the accelerator science field. The Half-wave resonator could provide us data across frequencies of …

Characterization Of Losses In Superconducting Radio-Frequency Cavities By Combined Temperature And Magnetic Field Mapping, Ishwari Prasad Parajuli

Physics Theses & Dissertations

Superconducting radio-frequency (SRF) cavities are one of the fundamental building blocks of modern particle accelerators. To achieve the highest quality factors (10¹⁰-10¹¹), SRF cavities are operated at liquid helium temperatures. Magnetic flux trapped on the surface of SRF cavities during cool-down below the critical temperature is one of the leading sources of residual RF losses. Instruments capable of detecting the distribution of trapped flux on the cavity surface are in high demand in order to better understand its relation to the cavity material, surface treatments and environmental conditions. We have designed, developed, and commissioned two novel …

A Comparison Of Uniaxial Compressive Response And Inelastic Deformation Mechanisms In Freeze Cast Alumina-Epoxy Composites Without And With Rigid Confinement, Tareq Aljuhari

Mechanical & Aerospace Engineering Theses & Dissertations

Cellular ceramics have an array of improved mechanical properties that make them incredibly desired for different applications such as armor systems, aircraft structures, automobiles bumpers, and biomedical implants. It is also desirable that porous architecture could be shaped into bulk complicated shapes and easy to scale-up with low manufacturing cost. Despite several efficient techniques to fabricate cellular ceramics, some limitations are preventing us from meeting the high demand of the after mentioned applications. For that, freeze casting, also called ice-templating, is technique of solidifying an aqueous ceramic suspension under the effect of unidirectional temperature gradient. In this study, Ice-templated porous …

Multi-Technique Characterization Of Superconducting Materials For Particle Accelerator Applications, Junki Makita

Physics Theses & Dissertations

We investigated the performance limitations of superconducting radio-frequency (SRF) cavities and materials using multiple experimental techniques. In particular, this study focuses on understanding the surface properties of nitrogen-doped Nb cavities and superconducting thin films with higher T_c such as Nb₃Sn. The main goal of this work is to use different techniques to better understand each aspect of the complex loss mechanism in superconductors to further improve the already highly efficient SRF cavities.

Nitrogen doping applied to a Nb SRF cavity significantly improves the quality factor Q₀ compared to a conventional Nb cavity, at an expense of …

Development Of High Conductivity Copper Coatings For Srf Cavity, Himal Pokhrel

Physics Theses & Dissertations

The development of metallic coatings with high purity and high thermal conductivity at cryogenic temperature could be very important for application to the superconducting radiofrequency (SRF) cavity technology. The deposition of such bulk coatings on the outer surface of a niobium cavity could result in higher heat conductance and mechanical stiffness, both of which are crucial for enhancing the cavity performance at a reduced cost.

Cold spray technology was used to deposit bulk coatings of pure copper and copper-tungsten alloys on the niobium substrate and the samples of size 2 mm × 2 mm cross section were cut and subjected …

Numerical Calculation Of Losses Of Trapped Vortices Under Strong Rf Meissner Current And Dc Superheating Field In Type Ii Superconductors, Walive Pathiranage Manula Randhika Pathirana

Physics Theses & Dissertations

Research on the vortex dynamics and enhancing of superheating field in superconductors has attracted much attention in accelerator physics community to develop next-generation high-performance accelerator cavities. However, the extreme dynamics of curvilinear elastic vortices driven by very strong currents close to the depairing limit or superheating field of a superconductor with a nanostructured surface has not been well understood. We calculated the superheating field H_sh and critical momentum kc characterizing the wavelength of the instability λ_m of the Meissner state to flux penetration by solving numerically the Ginzburg-Landau equations. A bulk superconductor, superconductor with the inhomogeneous surface disorder …

Demonstration Of Visible And Near Infrared Raman Spectrometers And Improved Matched Filter Model For Analysis Of Combined Raman Signals, Alexander Matthew Atkinson

Electrical & Computer Engineering Theses & Dissertations

Raman spectroscopy is a powerful analysis technique that has found applications in fields such as analytical chemistry, planetary sciences, and medical diagnostics. Recent studies have shown that analysis of Raman spectral profiles can be greatly assisted by use of computational models with achievements including high accuracy pure sample classification with imbalanced data sets and detection of ideal sample deviations for pharmaceutical quality control. The adoption of automated methods is a necessary step in streamlining the analysis process as Raman hardware becomes more advanced. Due to limits in the architectures of current machine learning based Raman classification models, transfer from pure …

Effect Of Alkali On The Efficiency And Reliability Of Cu(In,Ga)Se2 Solar Cells, Shankar Karki

Physics Theses & Dissertations

The incorporation of alkali metal has contributed tremendously in a bid to realize greater than 20% efficient Cu(In,Ga)Se₂(CIGS) solar cells. Achieving high efficiency is one key parameter for the success of a photovoltaic technology but so is its long-term stability. In this thesis, the relationship between the performance of alkali treated Cu(In,Ga)Se₂ solar cells and their physicochemical, electronic and structural properties are explored through a comparative study between standard devices and alkali (K, Rb) treated devices. The alkali treated devices tend to have a lower concentration of E_v+0.98 eV trap, higher majority carrier concentration and …

Secondary Electron Emission From Plasma Processed Accelerating Cavity Grade Niobium, Miloš Bašović

Mechanical & Aerospace Engineering Theses & Dissertations

Advances in the particle accelerator technology have enabled numerous fundamental discoveries in 20th century physics. Extensive interdisciplinary research has always supported further development of accelerator technology in efforts of reaching each new energy frontier.

Accelerating cavities, which are used to transfer energy to accelerated charged particles, have been one of the main focuses of research and development in the particle accelerator field. Over the last fifty years, in the race to break energy barriers, there has been constant improvement of the maximum stable accelerating field achieved in accelerating cavities. Every increase in the maximum attainable accelerating fields allowed for higher …

Plasma Processing Of Superconducting Radio Frequency Cavities, Janardan Upadhyay

Physics Theses & Dissertations

The development of plasma processing technology of superconducting radio frequency (SRF) cavities not only provides a chemical free and less expensive processing method, but also opens up the possibility for controlled modification of the inner surfaces of the cavity for better superconducting properties. The research was focused on the transition of plasma etching from two dimensional flat surfaces to inner surfaces of three dimensional (3D) structures. The results could be applicable to a variety of inner surfaces of 3D structures other than SRF cavities. Understanding the Ar/Cl₂ plasma etching mechanism is crucial for achieving the desired modification of Nb …

Field Emission Studies Toward Improving The Performance Of Dc High Voltage Photoelectron Guns, Mahzad Bastaninejad

Mechanical & Aerospace Engineering Theses & Dissertations

Field emission is the main mechanism that prevents DC high voltage photoemission electron guns from operating at the very high bias voltages required to produce low emittance beams. Gas conditioning is shown to eliminate field emission from cathode electrodes used inside DC high voltage photoelectron guns. Measurements and simulation results indicate that gas conditioning eliminates field emission from cathode electrodes via two mechanisms: sputtering and implantation, with the benefits of implantation reversed by heating the electrode. The field emission characteristics of 5 stainless steel electrodes varied significantly upon the initial application of voltage but improved to nearly the same level …

Investigation Of Nbnx Thin Films And Nanoparticles Grown By Pulsed Laser Deposition And Thermal Diffusion, Ashraf Hassan Farha

Electrical & Computer Engineering Theses & Dissertations

Niobium nitride films (NbNx) were grown on Nb and Si (100) substrates using pulsed laser deposition (PLD), laser heating, and thermal diffusion methods. Niobium nitride films were deposited on Nb substrates using PLD with a Q-switched Nd: YAG laser (λ = 1064 nm, 40 ns pulse width, and 10 Hz repetition rate) at different laser fluences, different nitrogen background pressures and deposition temperatures. The effect of changing PLD parameters for films done by PLD was studied. The seen observations establish guidelines for adjusting the laser parameters to achieve the desired morphology and phase of the grown NbNx films.

When the …

Laser Processing Of Metals And Polymers, Senthilraja Singaravelu

Physics Theses & Dissertations

A laser offers a unique set of opportunities for precise delivery of high quality coherent energy. This energy can be tailored to alter the properties of material allowing a very flexible adjustment of the interaction that can lead to melting, vaporization, or just surface modification. Nowadays laser systems can be found in nearly all branches of research and industry for numerous applications. Sufficient evidence exists in the literature to suggest that further advancements in the field of laser material processing will rely significantly on the development of new process schemes. As a result they can be applied in various applications …

Excitation-Induced Ge Quantum Dot Growth On Si(100)-2x1 By Pulsed Laser Deposition, Ali Oguz Er

Physics Theses & Dissertations

Self-assembled Ge quantum dots (QD) are grown on Si(100)-(2×1) with laser excitation during growth processes by pulsed laser deposition (PLD). In situ reflection-high energy electron diffraction (RHEED) and post-deposition atomic force microscopy (AFM) are used to study the growth dynamics and morphology of the QDs. A Q-switched Nd:YAG laser (λ = 1064 nm, 40 ns pulse width, 5 J/cm² fluence, and 10 Hz repetition rate) were used to ablate germanium and irradiate the silicon substrate. Ge QD formation on Si(100)-(2×1) with different substrate temperatures and excitation laser energy densities was studied. The excitation laser reduces the epitaxial growth temperature …

Compensation Of Loss And Stimulated Emission Of Surface Plasmon Polaritons, Guohua Zhu

Electrical & Computer Engineering Theses & Dissertations

Surface plasmon polaritons (SPPs) have become in recent years an important research topic because of their interesting, physics and exciting potential applications, ranging from sensing and biomedicine to nanoscopic imaging and information technology. However, many applications of surface plasmon polaritons are hindered by one common cause—absorption loss in metal.

Over the years, numerous proposals have been made on how to conquer the plasmon loss. In this dissertation, (1) the known solutions to the loss problem by adding optical gain have been reviewed; (2) the properties of surface plasmon polaritons are studied theoretically, and the solution of the controversy regarding the …

Reflection High-Energy Electron Diffraction Studies Of Indium Phosphide (100) And Growth On Indium And Indium Nitride On Silicon (100), Mohamed Abd-Elsattar Hafez

Electrical & Computer Engineering Theses & Dissertations

Study of the effects of atomic hydrogen exposure on structure and morphology of semiconductor surfaces is important for fundamental properties and applications. In this dissertation, the electron yield of a hydrogen-cleaned indium phosphide (InP) surface was measured and correlated to the development of the surface morphology, which was monitored by in situ reflection high-energy electron diffraction (RHEED). Atomic hydrogen treatment produced a clean, well-ordered, and (2x4)-reconstructed InP(100) surface. The quantum efficiency, after activation to negative electron affinity, and the secondary electron emission were shown to increase with hydrogen cleaning time. RHEED patterns of low-index InP(100) surface were modified by the …

Dynamics Of Phase Transitions On Low-Index Metal Surfaces, Bo Lin

Electrical & Computer Engineering Theses & Dissertations

The surface superheating and phase transitions at the low-index surface of metal were investigated using conventional continuous and 100-ps time-resolved reflection high-energy electron diffraction. Three metal surfaces, In(111), Au(110) and Pb(111), have been investigated in this work. The high temperature behavior of the In(111) surface was investigated using reflection high-energy electron diffraction with 100-ps temporal resolution. The change of surface vacancy density on In(111) is observed from 300 K to near the bulk melting point. The vacancy-formation energy of In(111) surface is estimated from experimental results. The surface vacancy density is observed to increase with temperature; however, the average random …

Field Emission Based Sensors Using Carbon Nanotubes, Changkun Dong

Physics Theses & Dissertations

A number of sensitive applications would be greatly benefited by the development of better cold cathodes that employ the electron field emission process. Among the many kinds of field emitters that could be tried, carbon nanotubes (CNT) have a number of distinct advantages because of their unique geometrical structure, chemical inertness, mechanical stiffness, and high thermal and electrical conductivities. This dissertation describes research in which CNT cathodes were fabricated and their emission characteristics were measured.

Multi-walled carbon nanotubes (MWNT) were grown by chemical vapor deposition (CVD) on various substrates: Ni and Hastelloy gauze, 304 stainless steel (SS) plates, and Ni-coated …

Characterization Of Iron Oxides And Atmospheric Corrosion Of Steel, Sei Jin Oh

Physics Theses & Dissertations

The study of corrosion behavior was performed using three different analytical techniques, which provided information on the formation, development and layering of iron oxides on the corrosion products as a function of atmospheric conditions, exposure time and type of steel. In particular, the protective layer formed on weathering steel was investigated as a function of different amounts of alloying elements in the steel, atmospheric conditions and exposure times. Combined together, the results provided a better understanding of the atmospheric corrosion behavior of steel, and formed a part of database of the atmospheric corrosion characteristics.

Accurate characterization of the iron oxides …

Identification And Characterization Of The Iron-Zinc Intermetallics Formed In Galvanneal Steel, Richard Frederick George Grant

Physics Theses & Dissertations

The demand to improve the corrosion resistance of steel sheet, particularly for use within the automotive industry, has led to a dramatic increase in the use of coated steels in place of cold-rolled sheet steel. Galvanneal steel results from the post annealing of the zinc-coated steel sheet, in which iron and zinc are interdiffused to form an iron-zinc alloy coating. Within this alloy coating, four main iron-zinc phases, Zeta, Delta, Gamma-1, and Gamma may be present. Manufacture of the most suitable coating requires identifying which phases form during the galvannealing process, an understanding of the properties of each phase and …

Compensation And Characterization Of Gallium Arsenide, Randy A. Roush

Electrical & Computer Engineering Theses & Dissertations

The properties of transition metals in gallium arsenide have been previously investigated extensively with respect to activation energies, but little effort has been made to correlate processing parameters with electronic characteristics. Diffusion of copper in gallium arsenide is of technological importance due to the development of GaAs:Cu bistable photoconductive devices. Several techniques are demonstrated in this work to develop and characterize compensated gallium arsenide wafers. The material is created by the thermal diffusion of copper into silicon-doped GaAs. Transition metals generally form deep and shallow acceptors in GaAs, and therefore compensation is possible by material processing such that the shallow …

The Effects Of Electron Radiation On The Glass Transition Temperature Of A Polyetherimide, Kristen Tulloch Kern

Physics Theses & Dissertations

The effects of electron radiation on a polyetherimide (PEI), Ultem*, were investigated. In particular, the changes in the glass transition temperature (T_g) with absorbed radiation dose were studied. The polymer was exposed to mono-energetic beams of 100-keV electrons and 1.0-MeV electrons for doses up to 100 megagray (MGy). Dosimetry for the exposures was based on Monte-Carlo simulations of the transfer of energy from an energetic electron to the polymer and on comparison to Nylon standards. Dynamic mechanical analysis was used to determine the (T_g) for non-exposed PEI and the changes in (T_g) resulting from …