Physical Sciences and Mathematics Commons^™

Evaluation Of Fluorapatite As A Waste-Form Material: First Quarter Report (2004-05), October 1 - December 31, 2004, Dennis W. Lindle, Oliver Hemmers

Separations Campaign (TRP)

Fluorapatite, fluorinated calcium phosphate, has been identified as a potential matrix for the entombment of the zirconium fluoride fission product waste stream from the proposed FLEX process. If the efficacy of fluorapatite-based waste-storage can be demonstrated, then new and potentially more-efficient options for handling and separating high-level wastes, based on fluoride-salt extraction, will become feasible. This proposal will develop a dual-path research project to develop a process to fabricate a synthetic fluorapatite waste form for the ZrF₄, FP waste stream, characterize the waste form, examine its performance under environmental conditions, and correlate the behavior of the waste form …

Development Of Integrated Process Simulation System Model For Spent Fuel Treatment Facility (Sftf) Design: Quarterly Report October 1-December 31, 2004, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The Advanced Fuel Cycle Initiative (AFCI) and Transmutation Research Program- University Participation Program (TRP-UPP) supported by Department of Energy of the United States have been developing many important technologies for the transmutation of nuclear waste to address long-term disposal issues. While successfully embedding AMUSE module into a dedicated System Engineering Model (TRPSEMPro), developed by the Nevada Center for Advanced Computational Methods (NCACM) at the University of Nevada, Las Vegas collaborating with Argonne National Laboratory (ANL), ANL is interested in further simulating the Light Water Reactor (LWR) Spent Fuel Treatment Facility (SFTF) combining commercial process simulation and analysis packages and core …

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead-Alloys Coolant Systems, Yitung Chen

Transmutation Sciences Materials (TRP)

The goal of the proposed research project is to provide basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead-alloys (lead or lead-bismuth eutectic) coolant systems. It is widely recognized that the corrosiveness of the lead-alloys is a critical obstacle and challenge for which it can be safely used or applied in the nuclear coolant systems. Active oxygen control technique can promote the formation of the “self-healing” oxide films on the structural material surface, drastically reducing steel corrosion and coolant contamination. Many experiments of steels exposed to flowing lead-alloys have …

The Electrochemical Separation Of Curium And Americium: Quaterly Report August-December 2004, David W. Hatchett, Kenneth Czerwinski

Separations Campaign (TRP)

This research report outlines the current status and progress associated with the electrochemical separation of Curium and Americium. The following pages outline the progress on our project to date. We have been actively performing research on this project for three months and are currently on schedule in terms of the proposed timelines.

The initial focus of the project involved setting up the laboratories for the studies outlined in the grant proposal. The instrumentation needed included an electrochemical work station that will perform the bulk of the electrochemical studies. This instrument will complement the electrochemical instrumentation in Dr. Hatchett’s laboratory and …

Neutron Multiplicity Measurements For The Afci Program Quarterly Progress Report September-December 2004, Denis Beller

Transmutation Sciences Physics (TRP)

The U.S. Advanced Fuel Cycle Initiative (AFCI) is a program to develop economic and environmental methods to reduce the impact of waste from commercial nuclear fuel cycles. One concept for near-complete destruction of waste isotopes from used nuclear fuel is accelerator driven transmutation. High-power accelerators would be used to produce high-energy charged particles, which then collide with heavy metal targets to create a cascade of neutrons. These neutrons then cause a nuclear chain reaction in subcritical systems. Fission neutrons then transmute fissile waste isotopes as well as other problematic isotopes such as technetium-99 and iodine-129. To design these systems, complex …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry, Morphology, And Surface Preparation: Quarterly Report (October-December 2004), Allen L. Johnson, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

This project has four components:

(1) the fabrication of a materials test apparatus with unique capabilities,

(2) comparative studies of steel corrosion under gas phase conditions comparable to the Lead Bismuth Eutectic (LBE) oxygen control conditions,

(3) isotope labeling studies, and

(4) collaborative efforts with other workers in the field.

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Quarterly Report, October 2004 To December 2004, Earl Wolfram, Thomas Hartmann, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert matrix fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10% of ²³⁹Pu. Ceramics will be synthesized and characterized based on the reactor physics results. The solubility the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, will be investigated in a manner to provide …

Inside Unlv, Cate Weeks, Carol C. Harter, Holly Ivy De Vore, Gian Galassi, Diane Russell

Inside UNLV

No abstract provided.

Immobilization Of Fission Iodine By Reaction With A Fullerene Containing Carbon Compound And Insoluble Natural Organic Matrix, Spencer M. Steinberg, Gary Cerefice, David W. Emerson

Separations Campaign (TRP)

The recovery of iodine released during the processing of used nuclear fuel poses a significant challenge to the transmutation of radioactive iodine. During the first two years of this program we have examined the potential of Fullerene Containing Carbon compounds (FCC) developed by KRI, and natural organic matter (NOM) as sorbents for iodine released during the reprocessing of nuclear fuel. This work involved the development of bench-scale testing of the FCC and NOM material in a simulated process off-gas environment.

Research Objectives and Goals

• Develop bench-scale experimental set-up and procedures for simulating PUREX head-end vapor phase; Develop experimental procedures …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823 For Transmutation Applications: Final Progress Report (September 2003 – August 2004), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this task is to evaluate the tensile properties of three martensitic alloys namely, Alloys EP-823, HT-9 and 422 at temperatures relevant to the transmutation processes. Testing has been performed to evaluate the tensile properties of all three alloys at temperatures ranging from ambient to 600^°C. The test materials were thermally-treated (quenched and tempered) prior to the evaluation of their tensile properties. The deformation characteristics of these tensile specimens, upon completion of testing, were evaluated by scanning electron microscopy (SEM). Efforts were also made to identify and characterize defects such as dislocations using transmission electron microscopy …

Immobilization Of Fission Iodine By Reaction With A Fullerene Containing Carbon Compound And Insoluble Natural Organic Matrix: Quarterly Report August-September 2004, Spencer M. Steinberg

Separations Campaign (TRP)

During first year of the project we were able to demonstrate iodine sorption by a sphagnum peat and Ca(OH)2 mixture. We decided to explore varying the ratio of Ca(OH)2 to sphagnum on the retention of iodine in both the iodine generator experiments and the fuel rod simulator experiments.

We also constructed a device for simulating the dissolution of fuel rods. Early experiments were impacted by sorption of iodine onto various components of the sorption train. We have eliminated or minimized iodine sorption by the system components. We retested both FCC and the sphagnum using this device. In these experiments a …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (June 01 – August 31, 2004), Ajit K. Roy

Transmutation Sciences Materials (TRP)

Highlights of Test Results:

• Residual stress measurements by the RC method on cold-worked specimens showed tensile residual stresses in austenitic stainless steel. However, compressive residual stresses were observed in martensitic stainless steel. This difference may be attributed to the difference in metallurgical phases and microstructures resulting from different thermal treatments imparted to them.

• Residual stress measurements by both ND and RC techniques on welded specimens showed similar patterns. Welded specimens consisting of similar material showed tensile residual stresses in the vicinity of the fusion line (FL). However, welded specimens consisting of dissimilar materials (austenitic and martensitic stainless steel …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Neutronic Evaluation Of Zro2-Mgo Inert Fuels, E. Fridman, A. Galperin, E. Shwageraus

Fuels Campaign (TRP)

Second task of the BGU part of “Dissolution, Reactor, and Environmental Behavior of ZrO₂-MgO Inert Fuel Matrix” project aims at evaluation of the fertile free fuel matrix composition effect on the fuel reactivity and corresponding reactivity limited burnup. Fertile free fuel with different MgO to ZrO₂ ratio in the matrix will require different PuO₂ loading in order to assure certain fuel cycle length. This is due to the fact that absorption cross section of Zr is slightly higher than that of Mg, although absorption in both of these elements is small compared to Pu. Therefore, the …

Development Of A Systems Engineering Model Of The Chemical Separations Process, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The whole chemical separation process is complex to the point that definitely requires certain level of systematic coordination. To perform smoothly and meet the target extraction rates among those processes, this research proposed a general-purpose systems engineering model.

A general purposed systems engineering model, Transmutation Research Program System Engineering Model Project (TRPSEMPro), was developed based on the above design concept. The system model includes four main parts: System Manager, Model Integration, Study Plan, and Solution Viewer. System Manager supervises all the case (problem) creation, and functionality definition. Model Integration identifies chemical extraction processes and their execution sequence. Study Plan is …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Final Report, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The whole chemical separation process is complex to the point that definitely requires certain level of systematic coordination. To perform smoothly and meet the target extraction rates among those processes, this research proposed a general-purpose systems engineering model.

A general purposed systems engineering model, Transmutation Research Program System Engineering Model Project (TRPSEMPro), was developed based on the above design concept. The system model includes four main parts: System Manager, Model Integration, Study Plan, and Solution Viewer. TRPSEMPro can apply not only to chemical separation process, but also a general system model.

Software engineering and Object Oriented Analysis and Design (OOA&D) …

Evaluation Of Fluorapatite As A Waste-Form Material: Fourth Quarter Report, June 1 - September 30, 2004, Dennis W. Lindle, Oliver Hemmers

Separations Campaign (TRP)

Fluorapatite, fluorinated calcium phosphate, has been identified as a potential matrix for the entombment of the zirconium fluoride fission product waste stream from the proposed FLEX process. If the efficacy of fluorapatite-based waste-storage can be demonstrated, then new and potentially more-efficient options for handling and separating high-level wastes, based on fluoride-salt extraction, will become feasible. This proposal will develop a dual-path research project to develop a process to fabricate a synthetic fluorapatite waste form for the ZrF₄, FP waste stream, characterize the waste form, examine its performance under environmental conditions, and correlate the behavior of the waste form …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (July 1 – Sept. 30, 2004), Yingtao Jiang, Bingmei Fu

Transmutation Sciences Materials (TRP)

Dr. Jiang Ma and Mr. Xiaolong Wu worked in LANL between July 1 and Sept. 15 to conduct the experiment. Test of the corrosion of different materials in LBE was performed. The influence of the process of gas introduction to the LBE was studied. Data analysis work was performed based on accumulated data. In the same time, progress has been made in the simulation for transport in oxygen mixing, and one paper was presented in a conference. Another paper was composed and submitted to IEEE International Symposium of Circuits and Systems for the track Chemical Sensors. Preparation of a paper …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Quarterly Report, July 2004 To September 2004, Kenneth Czerwinski, Earl Wolfram

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10 % of ²³⁹Pu. Ceramics will be synthesized and characterized based on the reactor physics results. The solubility the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, will be investigated in a manner to provide …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Neutronic Evaluation Of Zro2-Mgo Inert Fuels, E. Fridman, A. Galperin, E. Shwageraus

Fuels Campaign (TRP)

This progress report presents results of analysis performed within the framework of “Dissolution, Reactor, and Environmental Behavior of ZrO₂-MgO Inert Fuel Matrix” project managed by University of Nevada at Las Vegas, Harry Reid Center for Environmental Studies.

The BGU working program includes the following four tasks:

1. Benchmark of computational tools

2. Determination of fissile Pu loading

3. Evaluation of burnable poison designs

4. Evaluation of reactivity feedback coefficients

This progress report presents the results of Task 1. The main objective of this task is to confirm the validity of the ELCOS ¹ code system for inert matrix …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Trp Final Report 09/01/2003-08/31/2004, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Fourth Quarterly Report 06/01/2004-08/31/2004, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Neutron Multiplicity Measurements For The Afci Program Quarterly Progress Report June-August 2004, Denis Beller

Transmutation Sciences Physics (TRP)

The U.S. Advanced Fuel Cycle Initiative (AFCI) is a program to develop economic and environmental methods to reduce the impact of waste from commercial nuclear fuel cycles. One concept for near-complete destruction of waste isotopes from used nuclear fuel is acceleratordriven transmutation. High-power accelerators would be used to produce high-energy charged particles, which then collide with heavy metal targets to create a cascade of neutrons. These neutrons then cause a nuclear chain reaction in subcritical systems. Fission neutrons then transmute fissile waste isotopes as well as other problematic isotopes such as technetium-99 and iodine-129. To design these systems, complex reactor …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Annual Progress Report (May 2003 – May 2004), Ajit K. Roy

Transmutation Sciences Materials (TRP)

As indicated in the original proposal, the primary objective of this task was to evaluate the effect of hydrogen on environment-assisted cracking of candidate target structural materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization were martensitic stainless steels including Alloy EP 823, HT-9, and Type 422 stainless steel. The susceptibility to stress corrosion cracking (SCC) of these materials were evaluated in neutral and acidic aqueous environments using smooth and notched tensile specimens under constant-load (CL) and slow-strain-rate (SSR) conditions. Further, the …

Spectroscopic And Microscopic Investigation Of The Corrosion Of 316/316l Stainless Steel By Lead-Bismuth Eutectic (Lbe) At Elevated Temperatures: Importance Of Surface Preparation, Allen L. Johnson, Denise Parsons, Julia Manzerova, Dale L. Perry, Daniel Koury, Brian D. Hosterman, John Farley

Transmutation Sciences Materials (TRP)

The corrosion of steel by lead–bismuth eutectic (LBE) is an important issue in proposed nuclear transmutation schemes. Russian scientists at the IPPE exposed steel samples to oxygen-controlled LBE at temperatures up to 823 K and exposure times up to 3000 h. We have characterized these post-exposure steel samples and unexposed controls, using scanning electron microscopy (SEM), energy-dispersive X-ray analysis (EDAX) and X-ray photoelectron spectroscopy (XPS). Previous researchers have investigated the corrosion by LBE of steel of varying composition. In the present work, we compared two samples having the same composition (standard nuclear grade 316/316L) but different surface preparation: a cold-rolled …

Immobilization Of Fission Iodine By Reaction With A Fullerene Containing Carbon Compound And Insoluble Natural Organic Matrix: Quaterly Report April-June 2004, Spencer M. Steinberg

Separations Campaign (TRP)

The recovery of iodine released during the processing of used nuclear fuel poses a significant challenge to the transmutation of radioactive iodine. This proposal will develop and examine the use of Fullerene Containing Carbon (FCC) compounds as potential sorbents for iodine release from the reprocessing of nuclear fuel. This work will also include the development of bench-scale testing capabilities at UNLV to allow the testing of the FCC material in a simulated process off-gas environment. This experimental capability will also be used to test other potential sorption materials and processes, such as natural organic matter (NOM) and other promising alternatives. …

Evaluation Of Fluorapatite As A Waste-Form Material: Third Quarter Report, March 1- May 31, 2004, Dennis W. Lindle, Oliver Hemmers

Separations Campaign (TRP)

Fluorapatite, fluorinated calcium phosphate, has been identified as a potential matrix for the entombment of the zirconium fluoride fission product waste stream from the proposed FLEX process. If the efficacy of fluorapatite-based waste-storage can be demonstrated, then new and potentially more-efficient options for handling and separating high-level wastes, based on fluoride-salt extraction, will become feasible. This proposal will develop a dual-path research project to develop a process to fabricate a synthetic fluorapatite waste form for the ZrF₄, FP waste stream, characterize the waste form, examine its performance under environmental conditions, and correlate the behavior of the waste form …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Third Quarterly Report 03/01/2004-05/31/2004, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Electrochemical Separation Of Curium And Americium, David W. Hatchett, Kenneth Czerwinski

Separations Campaign (TRP)

The objective of this project is to develop a method for the separation of Am from Cm based on electrochemical techniques. Electrochemical systems that allow the thermodynamics of actinide and lanthanide complexes to be systematically evaluated and tuned will be examined. The influence of complex formation on the ability to selectively isolate a given species electrochemically will be evaluated. Metal-ligand complex formation provides a useful derivation technique to increase solubility in solution environments that favor precipitation. In addition, the thermodynamic properties of a complex relative to the isolated species may be shifted to more suitably measurable electrochemical separation regimes. Electrochemical …

Fundamental Chemistry Of U And Pu In The Tbp-Dodecane-Nitric Acid System, Kenneth Czerwinski, Byron Bennett

Separations Campaign (TRP)

The speciation of hexavalent U and tetravalent Pu will be examined in the TBP-dodecane-nitric acid systems. This topic is chosen based on data needs for separation modeling identified by the AFCI. Emphasis will be placed on studying the influence of nitrate and acetohydroxamic acid on U and Pu speciation as well as conditions where a third phase forms in the organic phase. The organic phase will be 30% TBP in dodecane. Equal volumes of aqueous and organic phase will be used. The speciation of the actinides in the aqueous and organic phase will be determined by a number of different …

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications, Biswajit Das

Transmutation Sciences Materials (TRP)

The objective of this project is to develop a novel nanostructure based coating technology that will provide significantly improved corrosion resistance for steel in LBE at elevated temperatures (500 - 600^oC), as well as provide long-term reliability under thermal cycling. The nanostructure based coatings will consist of a layer of nanoporous alumina with the pores filled with an oxidizing metal such as Cr, followed by a capping layer of alumina. Alumina, which is a robust anti-corrosion material, provides corrosion resistance at elevated temperatures. The Cr serves two purposes: (1) it acts as a solid filler material for the …