Physical Sciences and Mathematics Commons^™

Coordinated Unmanned Aircraft System (Uas) And Ground-Based Weather Measurements To Predict Lagrangian Coherent Structures (Lcss), Peter J. Nolan, James Pinto, Javier González-Rocha, Anders Jensen, Christina N. Vezzi, Sean C. C. Bailey, Gijs De Boer, Constantin Diehl, Roger Laurence Iii, Craig W. Powers, Hosein Foroutan, Shane D. Ross, David G. Schmale Iii

Mechanical Engineering Faculty Publications

Concentrations of airborne chemical and biological agents from a hazardous release are not spread uniformly. Instead, there are regions of higher concentration, in part due to local atmospheric flow conditions which can attract agents. We equipped a ground station and two rotary-wing unmanned aircraft systems (UASs) with ultrasonic anemometers. Flights reported here were conducted 10 to 15 m above ground level (AGL) at the Leach Airfield in the San Luis Valley, Colorado as part of the Lower Atmospheric Process Studies at Elevation—a Remotely-Piloted Aircraft Team Experiment (LAPSE-RATE) campaign in 2018. The ultrasonic anemometers were used to collect simultaneous measurements of …

Optimal Placement Of Distributed Energy Storage Systems In Distribution Networks Using Artificial Bee Colony Algorithm, Choton K. Das, Octavian Bass, Ganesh Kothapalli, Thair S. Mahmoud, Daryoush Habibi

Research outputs 2014 to 2021

The deployment of utility-scale energy storage systems (ESSs) can be a significant avenue for improving the performance of distribution networks. An optimally placed ESS can reduce power losses and line loading, mitigate peak network demand, improve voltage profile, and in some cases contribute to the network fault level diagnosis. This paper proposes a strategy for optimal placement of distributed ESSs in distribution networks to minimize voltage deviation, line loading, and power losses. The optimal placement of distributed ESSs is investigated in a medium voltage IEEE-33 bus distribution system, which is influenced by a high penetration of renewable (solar and wind) …

First Observation Of P-Odd Gamma Asymmetry In Polarized Neutron Capture On Hydrogen, D. Blyth, J. Fry, N. Fomin, R. Alarcon, L. Alonzi, E. Askanazi, S. Baeßler, S. Balascuta, L. Barrón-Palos, Alex Barzilov, J. D. Bowman, N. Birge, J. R. Calarco, T. E. Chupp, V. Cianciolo, C. E. Coppola, C. B. Crawford, K. Craycraft, D. Evans, C. Fieseler, E. Frlež, I. Garishvili, M. T. W. Gericke, R. C. Gillis, K. B. Grammer, G. L. Greene, J. Hall, J. Hamblen, C. Hayes, E. B. Iverson, M. L. Kabir

Mechanical Engineering Faculty Research

We report the first observation of the parity-violating gamma-ray asymmetry A(gamma)(np) in neutron-proton capture using polarized cold neutrons incident on a liquid parahydrogen target at the Spallation Neutron Source at Oak Ridge National Laboratory. A(gamma)(np) isolates the Delta I = 1, S-3(1)-> P-3(1) component of the weak nucleon-nucleon interaction, which is dominated by pion exchange and can be directly related to a single coupling constant in either the DDH meson exchange model or pionless effective field theory… See full text for full abstract.

College Of Engineering Senior Design Competition Fall 2018, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Cost Benefit Analysis Of Led Vs Florescent Lighting, Kurtis Clark, Phillip Humphrey

Student Research

Over the last few years, the state of Oklahoma has been looking at ways to reduce expenses to address concerns about a budget deficit. There have been efforts made to reduce expenses due to the use of energy. It has been said, when the lights are on, work is getting done. Running lights is therefore the cost of doing business. Our research examines the question, “is there a way to provide better lighting while operating at a lower cost.” This research examines the current lighting at Southwestern State University, primarily fluorescent lighting (FL), and a cost benefit analysis of switching …

Fluted Films, Nathan B. Spiers, Mohammad M. Mansoor, Jesse Belden, Randy Craig Hurd, Zhao Pan, Tadd T. Truscott

Mechanical and Aerospace Engineering Faculty Publications

This paper is associated with a poster winner of a 2017 APS/DFD Milton van Dyke Award for work presented at the DFD Gallery of Fluid Motion. The original poster is available from the Gallery of Fluid Motion, https://doi.org/10.1103/APS.DFD.2017.GFM.P0030

Interface Model Of Pem Fuel Cell Membrane Steady-Dtate Behavior, Russell L. Edwards, Ayodeji Demuren

Mechanical & Aerospace Engineering Faculty Publications

Modeling works which simulate the proton-exchange membrane fuel cell with the computational fluid dynamics approach involve the simultaneous solution of multiple, interconnected physics equations for fluid flows, heat transport, electrochemical reactions, and both protonic and electronic conduction. Modeling efforts vary by how they treat the physics within and adjacent to the membrane-electrode assembly (MEA). Certain approaches treat the MEA not as part of the computational domain, but rather an interface connecting the anode and cathode computational domains. These approaches may lack the ability to consistently model catalyst layer losses and MEA ohmic resistance. This work presents an upgraded interface formulation …

Considerations For Atmospheric Measurements With Small Unmanned Aircraft Systems, Jamey D. Jacob, Phillip B. Chilson, Adam L. Houston, Suzanne Weaver Smith

Mechanical Engineering Faculty Publications

This paper discusses results of the CLOUD-MAP (Collaboration Leading Operational UAS Development for Meteorology and Atmospheric Physics) project dedicated to developing, fielding, and evaluating integrated small unmanned aircraft systems (sUAS) for enhanced atmospheric physics measurements. The project team includes atmospheric scientists, meteorologists, engineers, computer scientists, geographers, and chemists necessary to evaluate the needs and develop the advanced sensing and imaging, robust autonomous navigation, enhanced data communication, and data management capabilities required to use sUAS in atmospheric physics. Annual integrated evaluation of the systems in coordinated field tests are being used to validate sensor performance while integrated into various sUAS platforms. …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

Implementation Of An Implicit Solver In Adcirc Storm Surge Model, Abdullah Alghamdi, Muhammad K. Akbar

Mechanical and Manufacturing Engineering Faculty Research

The current state of science does not offer any remedy to stop a hurricane from occurring. Therefore, accurate storm surge models capable of predicting water velocity and elevation are indispensable. In this paper, the implementation of an implicit solver in the Advanced Circulation (ADCIRC) storm surge model is presented. The implemented implicit solver uses hybrid finite element and finite volume techniques for solving shallow water equations. Objectives of this research include: Enhancing numerical stability, providing an option of using large timesteps, and the usage of a relatively easier mathematical formulation than the existing one in ADCIRC. The storm surge hindcast …

Modeling Of Cloud-Based Digital Twins For Smart Manufacturing With Mt Connect, Liwen Hu, Ngoc-Tu Nguyen, Wenjin Tao, Ming-Chuan Leu, Xiaoqing Frank Liu, Rakib Shahriar, S M Nahian Al Sunny

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The common modeling of digital twins uses an information model to describe the physical machines. The integration of digital twins into productive cyber-physical cloud manufacturing (CPCM) systems imposes strong demands such as reducing overhead and saving resources. In this paper, we develop and investigate a new method for building cloud-based digital twins (CBDT), which can be adapted to the CPCM platform. Our method helps reduce computing resources in the information processing center for efficient interactions between human users and physical machines. We introduce a knowledge resource center (KRC) built on a cloud server for information intensive applications. An information model …

Worker Activity Recognition In Smart Manufacturing Using Imu And Semg Signals With Convolutional Neural Networks, Wenjin Tao, Ze-Hao Lai, Ming-Chuan Leu, Zhaozheng Yin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In a smart manufacturing system involving workers, recognition of the worker's activity can be used for quantification and evaluation of the worker's performance, as well as to provide onsite instructions with augmented reality. In this paper, we propose a method for activity recognition using Inertial Measurement Unit (IMU) and surface electromyography (sEMG) signals obtained from a Myo armband. The raw 10-channel IMU signals are stacked to form a signal image. This image is transformed into an activity image by applying Discrete Fourier Transformation (DFT) and then fed into a Convolutional Neural Network (CNN) for feature extraction, resulting in a high-level …

Designing Model Experiments Around Harriet Tubman Middle School, Ryan Crist, Sarah Smith, Greg Sakradse, Ryan Scott

Undergraduate Research & Mentoring Program

Air quality is of concern in densely populated areas and especially near sources of inefficiently exhausted fossil fuel such as near the highway. Harriet Tubman middle school in North Portland, Oregon is situated alongside highway 5. Here, model experiments are designed and proposed to observe the instantaneous flow fields reflect modifications. LIDAR data was used to model the school and surrounding topography three-dimensionally in order to construct a model school and surrounding area from laser cut cardboard with a surface smoothed with paper mache. This model will be placed in the Portland State University wind tunnel; transport of mean and …

Analysis Of Surface Integrity In Machining Of Aisi 304 Stainless Steel Under Various Cooling And Cutting Conditions, F. Klocke, B. Döbbeler, S. Lung, S. Seelbach, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Recent studies have shown that machining under specific cooling and cutting conditions can be used to induce a nanocrystalline surface layer in the workspiece. This layer has beneficial properties, such as improved fatigue strength, wear resistance and tribological behavior. In machining, a promising approach for achieving grain refinement in the surface layer is the application of cryogenic cooling. The aim is to use the last step of the machining operation to induce the desired surface quality to save time-consuming and expensive post machining surface treatments. The material used in this study was AISI 304 stainless steel. This austenitic steel suffers …

3d Printed Filar Micrometer, Emily Rull

Honors Program Projects

Background

Double stars are celestial objects that allow for calculating the mass of stars by assessing their orbits. Stellar mass affects every current model of stellar evolution, but the most accurate double star orbits can take decades to record. Due to the long-term nature of such observations and lack of groundbreaking research in double star studies, professional astronomers are no longer focused on making these measurements, so amateur astronomers can pick up where professionals have left off. Amateurs can only do this if they can get the equipment that they need at prices they can afford. A personally-manufactured filar micrometer …

Thermal Removal Of Carbon Dioxide From The Atmosphere: Energy Requirements And Scaling Issues, Ted Von Hippel

Publications

I conduct a systems-level study of direct air capture of CO2 using techniques from thermal physics. This system relies on a combination of an efficient heat exchanger, radiative cooling, and refrigeration, all at industrial scale and operated in environments at low ambient temperatures. While technological developments will be required for such a system to operate efficiently, those developments rest on a long history of refrigeration expertise and technology, and they can be developed and tested at modest scale. I estimate that the energy required to remove CO2 via this approach is comparable to direct air capture by other techniques. The …

Experimental Examination Of Vorticity Stripping From A Wing-Tip Vortex In Free-Stream Turbulence, Hari C. Ghimire, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

Time-resolved stereoscopic particle image velocimetry measurements were conducted of a wing-tip vortex decaying in free-stream turbulence. The objective of the research was to experimentally investigate the mechanism causing the increased rate of decay of the vortex in the presence of turbulence. It was observed that the circulation of the vortex core experienced periods of rapid loss and recovery when immersed in free-stream turbulence. These events were not observed when the vortex was in a laminar free stream. A connection was made between these events and distortion of the vortex, coinciding with stripping of core fluid from the vortex core. Specifically, …

Electroosmotic Flow Of Viscoelastic Fluid In A Nanoslit, Lanju Mei, Hongna Zhang, Hongxia Meng, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

The electroosmotic flow (EOF) of viscoelastic fluid in a long nanoslit is numerically studied to investigate the rheological property effect of Linear Phan-Thien-Tanner (LPTT) fluid on the fully developed EOF. The non-linear Poisson-Nernst-Planck equations governing the electric potential and the ionic concentration distribution within the channel are adopted to take into account the effect of the electrical double layer (EDL), including the EDL overlap. When the EDL is not overlapped, the velocity profiles for both Newtonian and viscoelastic fluids are plug-like and increase sharply near the charged wall. The velocity profile resembles that of pressure-driven flow when the EDL is …

Some Insights Into The Migration Of Double Imaginary Roots Under Small Deviation Of Two Parameters, Dina Alina Irofti, Keqin Gu, Islam Boussaada, Silviu-Iulian Niculescu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper studies the migration of double imaginary roots of the systems’ characteristic equation when two parameters are subjected to small deviations. The proposed approach covers a wide range of models. Under the least degeneracy assumptions, we found that the local stability crossing curve has a cusp at the point that corresponds to the double root, and it divides the neighborhood of this point into an S-sector and a G-sector. When the parameters move into the G-sector, one of the roots moves to the right halfplane, and the other moves to the left half-plane. When the parameters move into the …

Communication Based Control For Dc Microgrids, Mahmoud S. Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

Centralized communication-based control is one of the main methods that can be implemented to achieve autonomous advanced energy management capabilities in DC microgrids. However, its major limitation is the fact that communication bandwidth and computation resources are limited in practical applications. This can be often improved by avoiding redundant communications and complex computations. In this paper, an autonomous communication-based hybrid state/event driven control scheme is proposed. This control scheme is hierarchical and heuristic, such that on the primary control level, it encompasses state-driven local controllers, and on the secondary control level, an event-driven MG centralized controller (MGCC) is used. This …

Strong Stability Of A Class Of Difference Equations Of Continuous Time And Structured Singular Value Problem, Qian Ma, Keqin Gu, Narges Choubedar

SIUE Faculty Research, Scholarship, and Creative Activity

This article studies the strong stability of scalar difference equations of continuous time in which the delays are sums of a number of independent parameters tau_i, i = 1, 2, . . . ,K. The characteristic quasipolynomial of such an equation is a multilinear function of exp(-tau_i s). It is known that the characteristic quasipolynomial of any difference equation set in the form of one-delayper- scalar-channel (ODPSC) model is also in such a multilinear form. However, it is shown in this article that some multilinear forms of quasipolynomials are not characteristic quasipolynomials of any ODPSC difference equation set. The equivalence …

Resistance Temperature Detectors In A Cryostat Refrigeration System, Kirsten Marie Manahan, Alice Callen

STAR Program Research Presentations

The Large Synoptic Survey Telescope (LSST) is a ground-based telescope that will survey the Southern sky every few nights. Located in the telescope will be a 3.2 gigapixel digital camera. To ensure proper instrumentation of the camera, there must be a monitored stable temperature. As part of my research, I assembled resistance temperature detectors and tested them to verify their reliability in measuring temperature in the camera’s cryostat refrigeration cooling system. Resistance temperature detectors function by the principle of thermal resistivity, in which their electrical resistances vary as temperature varies. Through testing, I was able to determine whether these particular …

Insights Into The Magnetic Dead Layer In La0.7sr0.3mno3 Thin Films From Temperature, Magnetic Field And Thickness Dependence Of Their Magnetization, N. Mottaghi, M.S. Seehra, R. Trappen, S. Kumari, Chih-Yeh Huang, S. Yousefi, G.B. Cabrera, A.H. Romero, M.B. Holcomb

Faculty & Staff Scholarship

Experimental investigations of the magnetic dead layer in 7.6 nm thick film of La0.7Sr0.3MnO3 (LSMO) are reported. The dc magnetization (M) measurements for a sample cooled to T = 5 K in applied field H = 0 reveal the presence of negative remanent magnetization (NRM) in the M vs. H (magnetic field) measurements as well as in the M vs. T measurements in H = 50 Oe and 100 Oe. The M vs. T data in ZFC (zero-field-cooled) and FC (field-cooled) protocols are used to determine the blocking temperature TB in different H. Isothermal hysteresis loops at differ- ent T …

Investigation Of Toppling Ball Flight In American Football With A Mechanical Field-Goal Kicker, Chase M Pfeifer, Timothy J. Gay, Jeff A. Hawks, Shane Farritor, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

A mechanical field-goal kicking machine was used to investigate toppling ball flight in American football place-kicking, eliminating a number of uncontrollable impact variables present with a human kicker. Ball flight trajectories were recorded using a triangulation-based projectile tracking system to account for the football’s 3-dimensional position during flight as well as initial launch conditions. The football flights were described using kinematic equations relating to projectile motion including stagnant air drag and were compared to measured trajectories as well as projectile motion equations that exclude stagnant air drag. Measured football flight range deviations from the non-drag equations of projectile motion corresponded …

Strong Stability Of A Class Of Difference Equations Of Continuous Time And Structured Singular Value Problem, Qian Ma, Keqin Gu, Narges Choubedar

SIUE Faculty Research, Scholarship, and Creative Activity

This article studies the strong stability of scalar difference equations of continuous time in which the delays are sums of a number of independent parameters τi, i = 1, 2, . . . , K. The characteristic quasipolynomial of such an equation is a multilinear function of e−τis. It is known that the characteristic quasipolynomial of any difference equation set in the form of one-delay-per-scalar-channel (ODPSC) model is also in such a multilinear form. However, it is shown in this article that some multilinear forms of quasipolynomials are not characteristic quasipolynomials of any ODPSC difference equation set. The equivalence between …

Test 2204: John Deere 5090m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2197: John Deere 5125r Oc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2192: John Deere 5090r Pfc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2207: Challenger Mt743, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2206: Challenger Mt740, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …