Medicine and Health Sciences Commons^™

Longitudinal Oxygen Imaging In 3d (Bio)Printed Models, Ryan Curtis O'Connell

Graduate Theses, Dissertations, and Problem Reports

Electron paramagnetic resonance (EPR), and its molecular imaging modality, is a powerful tool to noninvasively map various biological and chemical markers within objects of interest. Reliable data acquisition is a major impeding factor for longitudinal hands-off measurements. Measurements are especially challenging in biomedical applications, as live objects are not static. Frequent changes occur that require constant fine recalibration of the EPR detection system, called the resonator. To enable longitudinal imaging, a technology permitting automatic digital control of resonator coupling, tuning, and EPR data acquisition was developed. Automation was achieved through the utilization of a microcontroller and digital peripheral components such …

A Highly Conductive, Flexible, And 3d-Printable Carbon Nanotube-Elastomer Ink For Additive Bio-Manufacturing, Andy Shar, Phillip Glass, Daeha Joung Ph.D.

Undergraduate Research Posters

The synthesis of a highly conductive, flexible, 3D-printable, and biocompatible ink has been of great interest in the field of bio-based additive manufacturing. Various applications include ultra-sensitive, microscale tactile sensors, patient-customizable scaffolds for cardiac and nerve tissue regeneration, and flexible electrocardiogram (ECG) electrodes. Here, a novel elastomeric carbon nanocomposite is presented consisting of amino-functionalized carbon nanotubes (CNT-NH₂) homogenously dispersed in a one-part room-temperature vulcanizing (RTV) silicone matrix. The use of acetone as a swelling solvent aids in electrical percolation through the elastomer matrix. CNT-NH₂ ratios can be tuned to fit various needs; higher tensile strength is favored …

Comparative Analysis Of 3d Printed Denture Resins With Traditional Denture Materials At The Micro Level, Aneeza Hussain, Caleb Beckwith, Gaffar Gailani

Publications and Research

The aim of this experiment was to evaluate and identify compression strength between traditionally manufactured acrylic dentures and additive manufacturing resin dentures. Specifically, the dentures produced by Uhler Dental, its Reveal line were compared against samples produced on the Formlabs Form 2 SLA, Stereolithography, 3D printer using their Denture Teeth A2 resin to test compression strength to assure they are compatible with the occlusal forces in the oral cavity. Using the ZwickRoell tensile testing machine, it appeared that the acrylic dentures were half as strong as the resin dentures. Then we went ahead to and did a comparative analysis under …

Exploring Fused Deposition Modeling (Fdm) Three-Dimensional Printing Tablet Design Options For Pharmaceutical Dosage Forms, Guluzar Gorkem Buyukgoz

Dissertations

This dissertation examines the use of Fused Deposition Modeling (FDM) based three-dimensional (3D) printing approach for developing patient-specific dosage forms and addressing related technical challenges in such drug delivery systems. The first main objective is to explore pharmaceutical tablet design options using novel FDM 3D printing technology as the drug delivery platform such that drug form and tablet properties are tailored by considering patient age-specific formulations and dissolution control. Of the five different design options, two proposed options meet the main objective of providing similar drug release, whereas the popular option of fixed drug concentration but differing tablet size could …

In The Pursuit Of Assistance: A Team's Desire To Not Let A Congenital Amputation Get In A Young Boy's Way, Carl Russell Iii, Gavin Loucks, Kirsten Wozniak

Purdue Journal of Service-Learning and International Engagement

EPICS is a service-learning design program run through Purdue University. It strives to teach students design skills through providing for individuals, communities, and organizations in the surrounding area while mirroring engineering industry standards. BME (Biomedical Engineering) is a team within EPICS that strives to serve community partners through biomedical applications. William Sevick is an elementary school student with a congenital arm amputation. William and his family have been working with the BME team for the past three years designing assistive devices with the purpose of improving his actions in daily life such as eating, playing games, and riding his bike.

Metal Additive Manufacturing For Fixed Dental Prostheses, Mai El Najjar

Electronic Thesis and Dissertation Repository

The use of additive manufacturing (AM) in dentistry has gained momentum in recent years. However, high initial costs and uncertainty surrounding the quality of AM products are considered barriers to their use. This research compared dental substructures fabricated by AM versus conventional casting and milling.

Cobalt-chromium alloy rectangular bars and three-unit bridge substructures were fabricated by AM, casting or milling. Bars manufactured by AM exhibited superior flexural strength, shear bond strength of porcelain coating, and Vickers hardness. Bridge substructures fabricated by AM showed similar flexural stiffness to cast, similar flexural loads at failure to milled and cast, and overall accuracy …

Faculty Instruction Face Shield Project, David Holden, John Schneiderhan

Michigan Tech 3D Designs

Early in the spring of 2020 project contributors David Holden and John Schneiderhan began test printing a variety of open source Personal Protective Equipment (PPE)/Covid related items that could help protect or prevent the spread of the emerging virus. With assistance from Pete Baril of the Western Upper Peninsula Health Department (WUPHD) approval was obtained for the face shields to be used in the health care and nursing homes in the area. With the support and approval from university and library administration efforts were coordinated with Dr. Joshua Pearce and the students from the MOST lab to concentrate on the …

Left Atrial Appendage Printing Process, Areli Reyes, Brandon James Mukai, Mia Noelle Von Knorring

Biomedical Engineering

The left atrial appendage senior design team aims to assist in closing off the left atrial appendage that is susceptible to coagulation due to non-valvular atrial fibrillation. Coagulation in the left atrial appendage (LAA) can be life threatening as it can lead to a stroke. Dr. Chris Porterfield performs a procedure that uses the Boston Scientific Watchman to close the appendage. He finds that sizing the Watchman properly is difficult with limited visuals from live CT scans. He proposed converting the CT scans into a 3D printed model of the left atrial appendage and left atrium so he can visually …

Improving 3d Printed Prosthetics With Sensors And Motors, Rachel Zarin

Honors Projects

A 3D printed hand and arm prosthetic was created from the idea of adding bionic elements while keeping the cost low. It was designed based on existing models, desired functions, and materials available. A tilt sensor keeps the hand level, two motors move the wrist in two different directions, a limit switch signals the fingers to open and close, and another motor helps open and close the fingers. All sensors and motors were built on a circuit board, programmed using an Arduino, and powered by a battery. Other supporting materials include metal brackets, screws, guitar strings, elastic bands, small clamps, …

Three Professions Come Together For An Interdisciplinary Approach To 3d Printing: Occupational Therapy, Biomedical Engineering, And Medical Librarianship, Joan Wagner, Laurel Scheinfeld, Blanche Leeman, Keith Pardini, Jamie Saragossi, Katie Flood

Library Faculty Publications

Background: Although many libraries have offered 3D printing as a service or available technology, there is a lack of information on course-integrated programs for 3D printing in which the library played a primary role. Therefore, librarians at the Touro College School of Health Sciences began exploring 3D printing for inclusion in the occupational and physical therapy curriculum. Case Presentation: The goal of this project was to educate occupational and physical therapy students and faculty about the potential applications of 3D printing in health care and provide hands-on experience, while increasing collaboration between librarians and faculty. Students’ tasks included designing and …

Developmental Steps For A Functional Three-Dimensional Cell Culture System For The Study Of Asymmetrical Division Of Neural Stem Cells, Martina Zamponi

Biomedical Engineering Theses & Dissertations

Stem cells are a cell type present during and following development, which possess self- renewal properties, as well as the ability to differentiate into specific cells. Asymmetrical division is the cellular process that allows stem cells to produce one differentiated and one un-differentiated daughter cell during the same mitotic event. Insights in the molecular mechanisms of such process are minimal, due to the absence of effective methods for its targeted study. Currently, traditional methods of investigation include monolayer cell culture and animal models. The first poses structural limitations to the accurate representation of human tissue and cell structures, while animal …

3d Printed Pla Scaffolds To Promote Healing Of Large Bone Defects, Jacob W. Cole, Tiera Martinelli, Mitchell T. Ryan, Sarah G. Seman, Daniel Sidle, Stephen R. Smith, Rocco J. Rotello, Timothy L. Norman

The Research and Scholarship Symposium (2013-2019)

One challenge modern medicine faces is the ability to repair large bone defects and stimulate healing. Small defects typically heal naturally, but large bone defects do not and current solutions are to replace the missing tissue with biologically inert materials such as titanium. This limits the amount of bone healing as the defect is not repaired but rather replaced. The focus of our research is to develop a method of using 3D printing to create biodegradable scaffolds which promote bone in-growth and replacement. To accomplish this we used poly lactic acid (PLA) filament and a desktop 3D printer. To promote …

Additive Manufacturing Techniques And Their Biomedical Applications, Yujing Liu, Wei Wang, Laichang Zhang

Research outputs 2014 to 2021

Additive manufacturing (AM), also known as three-dimensional (3D) printing, is gaining increasing attention in medical fields, especially in dental and implant areas. Because AM technologies have many advantages in comparison with traditional technologies, such as the ability to manufacture patient-specific complex components, high material utilization, support of tissue growth, and a unique customized service for individual patients, AM is considered to have a large potential market in medical fields. This brief review presents the recent progress of 3D-printed ­biomedical materials for bone applications, mainly for metallic materials, including multifunctional alloys with high strength and low Young’s modulus, shape memory alloys, …

A Multi-Channel 3d-Printed Bioreactor For Evaluation Of Growth And Production In The Microalga Dunaliella Sp, Cristian A. Cox

Electronic Theses and Dissertations

We explored the capabilities of additive manufacturing using a photo-cured jetted material 3D printer to manufacture a milli-microfluidic device with direct application in microalgae Dunaliella sp growth and intracellular compounds biosynthesis tests. A continuous microbioreactor for microalgae culture was CAD designed and successfully built in 1 hour and 49 minutes using black photopolymer cured by UV and a support material. The microreactor was made up of 2 parts including the bioreactor itself and a microchannel network for culture media fluids and microalgae. Both parts were assembled to form a single unit. Additional optical and auxiliar components were added. An external …

Nanotechnology And Additive Manufacturing Platforms For Clinical Medicine: An Investigation Of 3d Printing Bioactive Constructs And Halloysite Nanotubes For Drug Delivery And Biomaterials, Jeffery A. Weisman

Doctoral Dissertations

Personalized medicine requires the development of new technologies for controlled or targeted drug delivery. Three-dimensional (3D) printing and additive manufacturing techniques can be used to generate customized constructs for bioactive compound delivery. Nanotechnology in the form of nanoparticles, used as a stand-alone construct or for material enhancements, can significantly improve established biomaterials such as PMMA based bone cements or enable new technology to have enhanced capabilities. Combinations of the technologies can be used in such applications as infectious disease treatments, chemotherapeutic targeted drug delivery or targeted delivery of nearly any bioactive compound.

Chemotherapeutic or antibiotic enhanced 3D printing filaments were …