Operations Research, Systems Engineering and Industrial Engineering Commons^™

Validation Of Shoulder Strain Index, Fabiha Islam

Graduate Theses, Dissertations, and Problem Reports

Musculoskeletal disorders (MSDs) of shoulder are one of the most frequent and major causes of morbidity and pain among full-time workers in the USA. In 2018, shoulder disorders were the most severe type of MSDs in terms of lost workdays. Recent epidemiological studies have identified several biomechanical, organizational, and psychological factors that increase the risk of shoulder MSDs. Though multiple biomechanical studies have evaluated physical causal factors of shoulder MSDs with a goal of risk mitigation, literature lacks a standardized risk assessment tool. The main objective of this study was to validate a previously developed shoulder strain index. The strain …

Evaluation Of Fitts’ Throughput As A Possible Performance Measure For Manual Assembly Tasks, Pradyumna Bettagere Jagadish

Graduate Theses, Dissertations, and Problem Reports

Assembly lines are the backbone of the manufacturing sector. Workers at the assembly lines are expected to perform fast pace hand-arm exertions with precision and accuracy. To protect the workers from injuries, OSHA mandates the use of personal protective equipment (PPE) including gloves. Certain assembly operations require the use of special gloves. Some of these gloves can inhibit hand performance, further increasing the task difficulty. The Index of Difficulty (ID) is a metric measured in ‘bits’ quantifies task difficulty through the quotient of target width and target motion, i.e., distance travelled. The time required to complete the target motion is …

Assessment Of Heat Stress For Outdoor Work Conditions In Saudi Arabia, Jamal Alanazi

Graduate Theses, Dissertations, and Problem Reports

Outdoor workers have an increased risk of heat stress in Saudi Arabia since it is one of the hottest places in the Middle East. Recently, the government decided to limit outdoor work hours during the months of June, July, and August every year, and banned working under the direct sunlight from 12:00 to 03:00 p.m., although outdoor workers in the petroleum, natural gas, or emergency maintenance work industries are exempt from this prohibition. Traditionally, the efforts by safety and health professionals to mitigate work-related heat injury has been directed toward the assessment of environmental heat stress (e.g., wet-bulb globe temperature), …

Analysis Of Factors Influencing The Stationarity Of Surface Electromyography Signals Measured In Non-Fatigued Shoulder Muscles, Hui Ci

Graduate Theses, Dissertations, and Problem Reports

A reduction in the % stationarity of surface electromyography (SEMG) signals with respect to the initial or fresh condition is used to predict localized muscle fatigue. However, factors other than muscle fatigue can also influence the stationarity of SEMG signals. This study was aimed at analyzing the effect of various work/task related factors on the stationarity of SEMG signals obtained from non-fatigued shoulder muscles. Twelve participants were recruited for data collection and each one performed 120 trials characterized by the combination of 2 shoulder angles (60° and 120°), 2 planes of exertions (sagittal and scapular), 3 force levels (0lb, 2.5lb, …

Evaluation Of Control Strategies For Overhead Work Using Electromyography Of Rotator Cuff Muscles, Hossein Motabar

Graduate Theses, Dissertations, and Problem Reports

Work-related musculoskeletal disorders (MSDs) of shoulder have a significant impact on overall health and economics in the industrialized nations. Rotator cuff is the most frequently injured region in the shoulder complex. Overhead work is considered as one of the most predominant causes of rotator cuff injuries. The workers in construction, automotive, and aerospace industries are routinely exposed to overhead exertions. Elimination of overhead work is nearly impossible due to various task and technology constraints. Therefore, appropriate intervention strategies based on the engineering and administrative controls opt to be used to prevent the hazardous impact of overhead exertions. The objective of …

A Study Of Impact Protection Of Metacarpal Gloves, Faisal Mohammed Alessa

Graduate Theses, Dissertations, and Problem Reports

Work-related wrist, hand, and finger injuries are highly prevalent in manufacturing and extractive industries. An analysis of mining-related hand injury data from over the past two decades (Alessa et al., 2020) showed that hand injuries caused by insufficient protection against impact loads (e.g. struck by accidents) were categorized with high severity. Existing literature lacks clear classification and quantification methods for the protection provided by impact-resistant gloves (i.e. metacarpal gloves). A new method to establish a quantitative measure of performance for commonly used metacarpal gloves was developed and evaluated.

In the first specific aim, an experimental study using cadaveric hand specimens …

Implications Of Variability Of Electromyographic Measurements For Assessing Localized Muscle Fatigue, Hamad Nasser Alasim

Graduate Theses, Dissertations, and Problem Reports

The impact of work-related musculoskeletal disorders (WMSDs) is enormous due to a combination of direct and indirect costs associated with healthcare, lost workdays and human suffering. Because of the established relationship between Localized Muscle Fatigue (LMF) development and WMSDs, and in order to reduce and/or prevent WMSDs in workplaces, different fatigue assessment methods have been developed. Surface Electromyography (SEMG) is a commonly used LMF assessment technique. The SEMG signals are typically analyzed in time and frequency domains to predict LMF based on a relative change with respect to initial, or under no-fatigue conditions. Quantifying such change, however, relies on the …

Development Of A Task Analysis Tool To Estimate Shoulder Strain During A Lifting Task, Christopher Wayne Moore

Graduate Theses, Dissertations, and Problem Reports

Musculoskeletal disorders of the shoulder have a huge impact on the workplace and employees. Due to the complexity and high mobility of the shoulder, developing a task analysis tool with a focus on the shoulder is difficult, and while there are some ergonomic analysis tools that do consider the shoulder to varying degrees in the analysis, none focus purely on the shoulder. Therefore, this research was undertaken in an attempt to develop a shoulder-based task analysis tool for the shoulder. However, since the scope of work involving the shoulder is so vast, the tool in this research focuses on unobstructed, …

Can Fitts' Throughput Be A Predictor Of Muscle Fatigue – A Study Based On Metacarpal Gloves?, Sachin Sah

Graduate Theses, Dissertations, and Problem Reports

In this study, Fitts’ throughput was used to estimate throughput for metacarpal gloves. Fitts’ throughput combines speed and accuracy during target transfer/movement tasks into a single performance index. It was hypothesized that the throughput will be affected by the glove condition and it will exhibit a relationship with the physiological response of hand muscles and perceived exertions. Fifteen healthy participants (10 males, 5 females) were recruited for data collection. Each participant performed a series of target transfer tasks using four glove conditions: (1) a pigskin leather (glove 1); (2) a synthetic fiber glove (glove 2); (3) a goat-grain leather glove …