Operations Research, Systems Engineering and Industrial Engineering Commons^™

ℓ-Ctp: Utilizing Multiple Agents To Find Efficient Routes In Disrupted Networks, Andrew Alseth

Graduate Theses and Dissertations

Recent hurricane seasons have demonstrated the need for more effective methods of coping with flooding of roadways. A key complaint of logistics managers is the lack of knowledge when developing routes for vehicles attempting to navigate through areas which may be flooded. In particular, it can be difficult to re-route large vehicles upon encountering a flooded roadway. We utilize the Canadian Traveller’s Problem (CTP) to construct an online framework for utilizing multiple vehicles to discover low-cost paths through networks with failed edges unknown to one or more agents a priori. This thesis demonstrates the following results: first, we develop the …

Study On New Sampling Plans And Optimal Integration With Proactive Maintenance In Production Systems, Sinan Obaidat

Graduate Theses and Dissertations

Sampling plans are statistical process control (SPC) tools used mainly in production processes. They are employed to control processes by monitoring the quality of produced products and alerting for necessary adjustments or maintenance. Sampling is used when an undesirable change (shift) in a process is unobservable and needs time to discover. Basically, the shift occurs when an assignable cause affects the process. Wrong setups, defective raw materials, degraded components are examples of assignable causes. The assignable cause causes a variable (or attribute) quality characteristic to shift from the desired state to an undesired state.

The main concern of sampling is …

Models For Data Analysis In Accelerated Reliability Growth, Cesar Alexander Ruiz Torres

Graduate Theses and Dissertations

This work develops new methodologies for analyzing accelerated testing data in the context of a reliability growth program for a complex multi-component system. Each component has multiple failure modes and the growth program consists of multiple test-fix stages with corrective actions applied at the end of each stage. The first group of methods considers time-to-failure data and test covariates for predicting the final reliability of the system. The time-to-failure of each failure mode is assumed to follow a Weibull distribution with rate parameter proportional to an acceleration factor. Acceleration factors are specific to each failure mode and test covariates. We …

Simulation Modeling Of Cross-Dock And Distribution Center Based Supply Chains, Ghewa Al Chall

Graduate Theses and Dissertations

Companies are implementing new strategies to meet the customer requirements in terms of quality, timing, and cost. One of these strategies is cross-docking, which can be defined as the process of consolidating the products coming from different suppliers, but having the same destination, with minimal handling and almost no storage between loading and unloading of the goods. The purpose of this research is to investigate the benefits of having a cross-docking facility in a supply chain. In this research, we focus on developing discrete event simulation models using the opensource Java Simulation Library (JSL). Also, we work on augmenting an …

Optimal Emergency Response Shelter Placement Based On Population Vulnerabilities, Alexander Johnson

Industrial Engineering Undergraduate Honors Theses

Hurricane Florence was a category 4 storm which caused an estimated $24 billion in damages and the loss of 53 lives. During and immediately following Florence, there were 235 shelters operating in and around the North Carolina (NC) area. These were used as temporary housing for storm victims and by emergency responders to distribute relief supplies and provide medical services. Emergency officials consider several factors when deciding where to open shelters, including, for example, proximity of victims and their levels of medical needs. Access disparities, or factors creating barriers that limit entry to shelters, put certain populations and regions at …

Improvement Of Geometric Quality Inspection And Process Efficiency In Additive Manufacturing, Yu Jin

Graduate Theses and Dissertations

Additive manufacturing (AM) has been known for its ability of producing complex geometries in flexible production environments. In recent decades, it has attracted increasing attention and interest of different industrial sectors. However, there are still some technical challenges hindering the wide application of AM. One major barrier is the limited dimensional accuracy of AM produced parts, especially for industrial sectors such as aerospace and biomedical engineering, where high geometric accuracy is required. Nevertheless, traditional quality inspection techniques might not perform well due to the complexity and flexibility of AM fabricated parts. Another issue, which is brought up from the growing …

Locating Relay Nodes To Maximize Wireless Sensor Network Lifetime: A Numerical Study, Maria Rene Arandia Jimenez

Industrial Engineering Undergraduate Honors Theses

A wireless sensor network (WSN) is a group of sensors deployed over an area, which monitor changes in the environment, collects them as data and forwards it between sensors through wireless links. Data is routed, either in a single-hop or multi-hop manner, with the goal of getting this collected data to the sink nodes, which have higher computational capabilities and connects the network with a user interface. Studies have determined that multi-hop WSNs that integrate relay nodes, which function is to only receive and forward data, can maximize lifetime network. A linear programming model, created by Chang and Tassiulas in …

Re-Evaluating Coverage Metrics For Wireless Sensor Network Border Security Applications, Kevin Haney

Industrial Engineering Undergraduate Honors Theses

Wireless sensor networks are an emerging technology used to monitor an environment over time. One specific application of the wireless sensor network is the border security application. Researchers have adapted coverage metrics from general wireless sensor network literature to fit the border security application. While some of the adapted metrics count the number of sensors detecting a potential target, others measure the distance between a potential target and its nearest sensor. No existing metric accounts for both of these factors. To take advantage of this gap and to attempt to increase the accuracy to which coverage is measured in this …

Curriculum Optimization Via Activity-On-Node Network Modeling, Caroline Rhomberg

Industrial Engineering Undergraduate Honors Theses

University degree plans must be carefully planned so that they allow students the best chance of succeeding. Although for the better, with the advancement of technology and its incorporation into the classroom, it can be argued that the complexity and difficulty of some long-established engineering core classes has changed. With this trend certain combinations of engineering courses have become unfavorable in terms of course withdrawal and fail rates stemming from the interaction of course challenges. A wealth of data has been collected on this topic and will be utilized in this project. As one can imagine, the probability of success …

Locating Emergency Shelters While Incorporating Spatial Factors, Justin Taylor

Graduate Theses and Dissertations

In the immediate response phase of a natural disaster, local governments and nonprofit agencies often establish shelters for affected populations. Decisions regarding at which locations to open shelters are made ad hoc based on available building inventory, and may result in high travel impedance to reach shelters and congestion. This thesis presents a shelter location optimization model based on the two-step floating catchment area (2SFCA) method. The 2SFCA method creates a shelter accessibility score for each areal unit (e.g., census block group) which represents the ability for persons in the unit to access shelter capacity with low travel impedance, relative …