Operations Research, Systems Engineering and Industrial Engineering Commons^™

Bikeshare Business Model For Cal Poly- San Luis Obispo, Justin Benson, Andrew Neil Gatchalian

Industrial and Manufacturing Engineering

With the increasing admittance of students into colleges and universities across the nation, the need for alternate modes of transportation is becoming more pressing. College and university campuses, as well as small cities, in which there is a college or university, are being overloaded with student cars. In San Luis Obispo specifically, parking on campus as well as downtown can be extremely difficult to find. Traffic is also getting progressively worse, especially at the hour when class begins/ends and student arrive to or leave campus. Financial reasons are yet another deterrent for students at Cal Poly. Parking permits, gas, and …

Redesign Of Talley Farm's "Fresh Harvest" Produce Program, Nicole Bordwell, John Rivera, Jared Toboni

Industrial and Manufacturing Engineering

Fresh Harvest, a Central Coast Community Supported Agriculture (CSA) program run by Talley Farms located in Arroyo Grande, CA, has a rapidly growing customer base. They harvest, package, and deliver boxes of fresh quality produce to almost 3000 subscribers. However, Talley Farms’ space for production and processing is limited and at times required for other aspects of business. This results in a problem where Talley Farms current processing system of produce for the Fresh Harvest program is not suitable for the forecasted growing demand. This report addresses the need to prepare for continued significant growth to the demand for Fresh …

Process Improvements Of Cilantro Harvesting With Ergonomic Considerations, Eric Penningroth, Branden Shimamoto

Industrial and Manufacturing Engineering

The problems presented by Talley Farms to the team were a lower than desired cilantro harvesting capacity and work health pertaining to lower back problems. The project objectives were to address and improve upon both of these objectives. To increase harvesting capacity, a simulation model was created using standard times from time studies. The simulation model helped to compare the different harvesting methods as well as the effect of the utilization of the on-site manager. The throughputs between each of the models were analyzed. To address ergonomic concerns, a work sampling study was conducted and it was determined that kneeling …

Effects Of Patient Factors On Implantation Rates In In Vitro Fertilization, Heidi Richardson, Sofia Soto

Industrial and Manufacturing Engineering

The purpose of this report is to evaluate the effects of patient factors and embryo quality on the implantation rate in In Vitro Fertilization (IVF). For this report, statistical methods are used to test the significance of several patient and embryo characteristics on embryo implantation rate. This project is an analysis of data collected from over 36,000 patients.

The analysis concluded several findings. There was enough statistical evidence to conclude that age was significant in regards to implantation rate and FSH levels. As the patient ages, the amount of FSH levels found in their blood increases. A patient with high …

Analysis And Improvement Of The Security Building At Pg&E Diablo Canyon Nuclear Power Plant, Alyssa Carter, Natalie Christa, Phuong Anh Pham Dinh

Industrial and Manufacturing Engineering

A new Security building was recently designed and built at the Pacific Gas and Electric (PG&E) Diablo Canyon Power Plant (DCPP).This building’s staff and equipment are responsible for performing routine inspections on all personnel entering the facility in order to prevent security-related incidents from occurring at the nuclear power plant. Similar to airport security procedures, the DCPP security building routine inspections include the use of x-ray machines, metal detectors, and explosive detectors.

The Power Plant periodically experiences pre-planned, preventive maintenance outages, that last 4-6 weeks. During an outage, a power plant reactor is shut down for maintenance, repair, and re-fueling. …

Semi-Automated Glass Mat Splice Operation For Asphalt Shingle Line, Justin Bracci, Harry Zhao, Chad Linafelter

Mechanical Engineering

The following report details the senior project sponsored by GAF Materials Corporation, Shafter, CA in regards to semi-automating a glass-mat splicing table for asphalt roofing shingle production. Herein includes details, research, design, and analysis regarding the semi-automation of the gluing processes for the splicing table. A working prototype was manufactured and tested for the future implementation onto GAF’s production line or further senior project involvement.

Methane Production By A Packed-Bed Anaerobic Digester Fed Dairy Barn Flush Water, Sean Richard Thomson

Master's Theses

Packed-bed digesters are an alternative to covered lagoon digesters for methane production and anaerobic treatment of dilute wastewaters such as dairy barn flush water. The physical media of packed-beds retain biofilms, often allowing increased treatment rates. Previous studies have evaluated several types of media for digestion of dilute wastewaters, but cost and media fouling have setback commercial development. A major operational cost has been effluent recirculation pumping.

In the present effort, a novel approach to anaerobic digestion of flush dairy water was developed at pilot-scale: broken walnut shells were used as a low-cost packed-bed medium and effluent recirculation was replaced …

Operational Planning In Combined Heat And Power Systems, Hariharan Gopalakrishnan

Doctoral Dissertations

This dissertation presents methodologies for operational planning in Combined Heat and Power (CHP) systems. The subject of experimentation is the University of Massachusetts CHP system, which is a 22 MWe/640 MBh system for a district energy application. Systems like this have complex energy flow networks due to multiple interconnected thermodynamic components like gas and steam turbines, boilers and heat recovery steam generators and also interconnection with centralized electric grids. In district energy applications, heat and power requirements vary over 24 hour periods (planning horizon) due to changing weather conditions, time-of-day factors and consumer requirements. System thermal performance is highly dependent …

Dissolution Rate And Mechanism Of Metals In Molten Aluminum Alloy A380, Hengyu Zhu

Open Access Theses

Shot sleeve is a very easily worn out part in a high-pressure die-casting machine due to serious dissolution of the area underneath the pouring hole. It is because during a normal pouring process, the high temperature molten aluminum will impact and dissolve that area of the shot sleeve by complex chemical and physical process. Rotation experiment was carried out to H13 and four kinds of refractory metal samples. SEM and EDS pictures were taken in order to investigate the microstructure and the dissolution mechanism of these materials. This suggests a high strength niobium is an ideal material for that area …

A Method To Develop Neck Injury Criteria To Aid Design And Test Of Escape Systems Incorporating Helmet Mounted Displays, Jeffrey C. Parr

Theses and Dissertations

HMDs are becoming common human-machine interface equipment in manned military flight, but introducing this equipment into the overall aircraft escape system poses new and significant system design, development, and test concerns. Although HMDs add capabilities, which improve operator performance, the increased capability is often accompanied by increased head supported mass. The increased mass can amplify the risk of pilot neck injury during ejection when compared to lighter legacy helmets. Currently no adequate USAF neck injury criteria exist to effectively guide the requirements, design, and test of escape systems for pilots with HMDs. This research effort presents a novel method to …

Optical Direct-Write Nanolithography Based On Self-Assembled Resist, Meghana Akella

Open Access Theses

Holographic display is being developed for next generation mobile phones. However, manufacturing of miniature gratings for the holographic projectors cost a few thousand dollars today, not making the concept practical for commercial purposes. In this thesis, we discuss the feasibility of self-assembled nanoparticles to manufacture holographic gratings cost-effectively and at the nanoscale. Using our approach, the gratings can be manufactured at the scale of 20nm and the cost per chip is expected to cost a few dollars.^ In this thesis, a hydrophobic SAM was used to modify the surface of silicon. Direct-write UV laser lithography was used for photothermal patterning …

2d Wireform Process Improvement, Katy Conlin, Carlo Ebora, Jordan Gamble

Mechanical Engineering

The body of this work has been created for Edwards Lifesciences in conjunction with senior project requirements. As such, the information produced and contained within is under a non‐disclosure agreement. As per request by sponsor, the body of the work will not be submitted to any outside parties, and the title page will serve as proof of completion.

Design Of A Custom Software Application To Monitor And Communicate Cnc Machining Process Information To Aid In Chatter Identification, Valerie Pezzullo

All Theses

In any manufacturing environment, it is important to be able to monitor the Computer Numerical Control (CNC) machining process so that high quality parts can be produced in the least amount of time in order to be profitable. This involves acquiring the proper parameters needed from the machine's controller, which can prove to be difficult with proprietary machine tools that tend to limit access to the internal data collected by the controller. This closed approach to controller design also means that many technological advances that have recently become prevalent in society are not being adopted in the manufacturing industry, preventing …

Probabilistic Fault Detection And Diagnostics For Packaged Air-Conditioner Outdoor-Air Economizers, Andrew L. Hjortland

Open Access Theses

Poor economizer control, economizer damper failure, and excess outdoor-air contribute to these performance degradations. In order to promote optimal rooftop air-conditioner (RTU) performance and reduce operating costs, an automated fault detection and diagnostics (AFDD) tool has been designed for RTUs with integrated economizers. Based on previously proposed methods, the proposed method advances the economizer fault detection and diagnosis components by using statistical classifiers in order to provide more robust, probabilistic fault outputs. A set of air-side virtual sensors has also been added to the method in order to expand the applicable range of conditions fault detection and diagnostics can be …

Design Of Transportation Process For Band Equipment, Marissa N. Blustein, Chris M. Kaye

Industrial and Manufacturing Engineering

The following report documents the attempt to design a safe and reliable process for transporting Louder Space’s musical gear that requires minimal physical demand. Design specifications were derived from customer requirements as well as human factors principles. The transportation process was broken down into systematic process steps and standardized, making use of lean methodologies in order to reduce the number of non-value steps involved. Furthermore, a model portable storage unit for miscellaneous gear was developed to the specifications determined by the band using 3D modeling, as well as certain limiting constraints. Once the customer approved the prototype, the product was …

Lean Fire Management: A Focused Analysis Of The Incident Command System Based On Toyota Production System Principles, Jeremiah S. Fugate

Theses and Dissertations--Mechanical Engineering

A primary role of the Incident Command System is to learn from past incidents, as illustrated by its origins in the wildland firefighting community. Successful emergency response operations under the Incident Command System has prompted its nationwide spread, this promulgation critically relies on the system’s capability to stabilize and continuously improve various aspects of emergency response through effective organizational learning. The objective of this study is to evaluate the potential to apply fundamental principles of the Toyota Production System (Lean manufacturing) to improve learning effectiveness within the Incident Command System. An in-depth review of literature and training documents regarding both …

Neuromodulation Based Control Of Autonomous Robots On A Cloud Computing Platform, Cameron Muhammad

Electronic Theses and Dissertations

In recent years, the advancement of neurobiologically plausible models and computer networking has resulted in new ways of implementing control systems on robotic platforms. The work presents a control approach based on vertebrate neuromodulation and its implementation on autonomous robots in the open-source, open-access environment of robot operating system (ROS). A spiking neural network (SNN) is used to model the neuromodulatory function for generating context based behavioral responses of the robots to sensory input signals. The neural network incorporates three types of neurons- cholinergic and noradrenergic (ACh/NE) neurons for attention focusing and action selection, dopaminergic (DA) neurons for rewards- and …