Operations Research, Systems Engineering and Industrial Engineering Commons^™

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Laboratory Evaluation Of High-Temperature Resistant Lysine-Based Polymer Gel Systems For Leakage Control, Tao Song, Xuyang Tian, Baojun Bai, Yugandhara Eriyagama, Mohamed Ahdaya, Adel Alotibi, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

In-situ crosslinking gel known for its cost-effectiveness, has been employed for decades to plug high-permeability features in subsurface environments. However, some commonly used crosslinkers are being phased out due to the increasingly rigorous environmental regulations. As a newly discovered environmentally friendly crosslinker, lysine can crosslink the partially hydrolyzed polyacrylamide through transamidation reaction. The present work aimed to study the effect of polymer composition and concentration on the gelation behavior of lysine and high molecular weight acrylamide-based polymers. Several commercial high molecular weight polymers with different contents of 2-Acrylamido-2-methyl-1-propane sulfonic acid (AMPS) including AN-105/125, SAV-55/37/28, and SAV-10 were deployed in this …

Strategy For Predictive Control Of The Rectification Process Based On A Model Controller With A Given Forecast, Ildar Rafkatovich Sultanov

Chemical Technology, Control and Management

A method is being developed to optimize the generated controls for the multicomponent distillation process with prediction, based on predictive data with a moving horizon. The difference between this method and the classical modeling approach, in which the percentage of the degree of opening of valves installed on the output streams of the column is used as control actions, is that control occurs on the feedback principle. The proposed method is based on the use of a dynamic process model to optimize control actions in real time in order to achieve certain production targets. The essence of the MPC approach …

Identification Of Faults In Highways Using Approximation Methods And Algorithms, Khudayberdiyev Khakkulmirzayevich Mirzaakbar, Anvar Asatilloyevich Ravshanov

Chemical Technology, Control and Management

Many fast Fourier transforms are used to identify defective parts of uneven surfaces on roads and send information to relevant organizations on the road, using the " RAVON YO‘LLAR" application installed on a mobile device during car movement. We determine the uneven parts of the road. Smooth and well-maintained roads reduce the risk of vehicle collisions, skidding and other road-related incidents. Timely measures contribute to overall safety, comfort and economic efficiency.

A Neural Network Model For Monitoring And Forecasting The Process Of Storing Oilseeds, N.A. Kabulov

Chemical Technology, Control and Management

The paper presents the results of research on the control, forecasting and management of the storage process of oilseeds. Vegetable oil production and energy consumption are two important factors of oilseed storage systems. The first ones should meet the needs of the population quantitatively and qualitatively. As a result, in order to properly control these two important aspects, it is necessary to maintain an appropriate microclimatic environment using a computational decision support system (DSS) that is able to adapt to changes in environmental characteristics. The multilayer perceptron neural network (MLP-NN) was developed to simulate the temperature and relative humidity profiles …

Synthesize A Neural Network Parameter Optimizer For An Adaptive Pid Controller, Nashvandova Gulruxsor Murot Qizi

Chemical Technology, Control and Management

Wide application of proportional-integral-differential (PID)-regulator in industry requires constant improvement of methods of its parameters superstructuring. In the paper, the questions of optimization of PID-regulator parameters with application of methods of neural network technology are considered. A methodology for selecting the architecture of neural network optimizer designed to determine the tuned parameters of PID regulator is proposed. The algorithm of training of the neural network, with the set on the basis of the method of inverse gradient propagation is offered. The proposed improved PID-neural regulator allowed to provide stabilization of neural network operation and its trainability in the control loop …

Development Of A Criterion Assessing The Level Of Relationship Of Multiple Identified Characteristics For Classification, Mirzoyan Mirzaaxmedovich Kamilov, Oybek Zokirovich Koraboshev, Bobomurod Mamitjonovich Tojiboev

Chemical Technology, Control and Management

This article discusses an optimized version of the standard design developed by Yu.I.Zhuravlev, an optimization procedure through an algebraic approach based on precedent algorithms that solves the problem of pattern identification. The formation of the convex hull of the recognition operator and corrective procedures of information models by mutual compensation of each other was also studied. In addition, the functional connection of recognition operators and the definition of idempotent connection of operators are analyzed.

Analytical-Critical Review Of Widely Used Industrial Devices For Drying Mineral Fertilizers, Djalolitdin Paxritdinovich Mukhitdinov, Aleksey Viktorovich Schulz

Chemical Technology, Control and Management

The article is devoted to the review of the modern state of research in the mineral fertilizers drying field, critical analysis and comparison of widely used drying apparatuses. There are procedures of preliminary equipment selection for soluble fertilizers industrial drying on the basis of such criteria as productivity, efficiency, energy saving, environmental impact degree, indicating the possible advantages and disadvantages of different application variants.

Calculation Of Hydraulic Resistance Of A Tubular-Gridse Nozzle With Spiral Turbulizers, Nurmukhamedov Habibulla Sagdullaevich, Mavlonov Elbek Tulkinovich, S.Kh. Nishonova, Kh.S. Nurmukhamedov

Chemical Technology, Control and Management

The article presents the results of an experimental study on the hydraulic resistance of a tubular-grid nozzle made of smooth pipes and pipes with spiral turbulators. Experiments were carried out with nozzles made of smooth pipes and pipes with turbulators. Spiral turbulators are placed discretely with a step t/d=0,3125-0,9375 and installed on a tube sheet in a checkerboard pattern with a step s/d=1,15-10. Experimental studies were carried out with air flow in the transition region.

It has been established that with increasing numerical values of the dimensionless parameter s/d, the resistance of the pipe package decreases from 1,3 to 1,8 …

Chromatographic Analysis Of The Chemical Composition Of Pyrolysis Distillate, Sh.T. Juraev, B.F. Muxiddinov, U.T. Tailakov

Chemical Technology, Control and Management

The paper presents the results of a study of the physico-chemical characteristics of the liquid fraction of products of thermal oxidative pyrolysis of worn tires. The mass fraction of the volatile gas compounds, the optimal boiling points of the obtained condensates and the flashpoint of pyrolysis liquids, together with the mass composition of cracking products of rubber products at high-temperature pyrolysis at a temperature of 800-900 °C, were determined. Chromatographic analysis allowed us to determine the composition, mainly the mass composition of pyrolysis products, which consisted of carbon (42.8%), higher aliphatic and aromatic hydrocarbons (17.0%), methane (10.2%), benzene (4.2%) and …

Integrated Computer-Aided Design, Experimentation, And Optimization Approach For Perovskites And Petroleum Packaging Processes, Swapana Subbarao Jerpoth

Theses and Dissertations

According to the World Economic Forum report, the U.S. currently has an energy efficiency of just 30%, thus illustrating the potential scope and need for efficiency enhancement and waste minimization. In the U.S. energy sector, petroleum and solar energy are the two key pillars that have the potential to create research opportunities for transition to a cleaner, greener, and sustainable future. In this research endeavor, the focus is on two pivotal areas: (i) Computer-aided perovskite solar cell synthesis; and (ii) Optimization of flow processes through multiproduct petroleum pipelines. In the area of perovskite synthesis, the emphasis is on the enhancement …

Developing Machine Learning And Time-Series Analysis Methods With Applications In Diverse Fields, Muhammed Aljifri

Theses and Dissertations

This dissertation introduces methodologies that combine machine learning models with time-series analysis to tackle data analysis challenges in varied fields. The first study enhances the traditional cumulative sum control charts with machine learning models to leverage their predictive power for better detection of process shifts, applying this advanced control chart to monitor hospital readmission rates. The second project develops multi-layer models for predicting chemical concentrations from ultraviolet-visible spectroscopy data, specifically addressing the challenge of analyzing chemicals with a wide range of concentrations. The third study presents a new method for detecting multiple changepoints in autocorrelated ordinal time series, using the …

Modeling Of Amine-Based Co2 Capture Process, Zafar Safarovich Turakulov

Chemical Technology, Control and Management

A significant factor influencing climate change is the release of carbon dioxide (CO₂) into the atmosphere as a consequence of human activities such as the combustion of fossil fuels. Climate change can be slowed down by taking action to mitigate industrial-scale CO₂ emissions. Currently, the most advanced technology for capturing CO₂ from industrial flue gases is the post-combustion CO₂ capture based on amine absorption. However, due to the high energy penalties of existing CO₂ capture technologies and insufficient carbon markets, it is necessary to develop methods that compete with these technologies or minimize their …

The Use Of Ultraviolet Radiation As A Means Of Destroying Microorganisms In Cherries, Jasur Safarov, Shaxnoza Sultanova, Pulatov M. Murodjon

Chemical Technology, Control and Management

The article discusses methods for extending the shelf life of cherries, having previously treated it with an ultraviolet ray. The article also presents the results obtained, which prove that the shelf life of cherries exposed to ultraviolet increases. At the same time, the article describes in detail the processing technique and presents the results of research.

Study Of Dynamic Characteristics Of The Mechanical Circuit Of The Developed Induction Inertial Vibration Transducer, Sulton Fayzullayevich Amirov, Asror Abdunabiyevich Shoimkulov

Chemical Technology, Control and Management

The article examines the dynamic characteristics of the mechanical circuit of the developed induction vibration transducer. It is found that in the investigated transducers forced oscillations occur with the frequency of the input disturbing force, the amplitude of forced oscillations does not depend on the initial conditions and time, and in forced oscillations with damping there is always a shift of the oscillation phase compared to the phase of the input disturbing force. It is shown that the induction vibration transducer reproduces the measured vibrations with small distortions only in a relatively narrow frequency region at frequencies of the input …

Mathematical Models And Calculation Of Parameters Of Optoelectronic Angular Displacement Converters, Yuriy Gennadyevich Shipulin, Azimjon Khusanov

Chemical Technology, Control and Management

The article discusses promising optoelectronic converters (OP) for wide application of angular movements. A methodology and diagram for calculating OP with the transverse movement of a moving element is presented; in order to simplify the calculation, the weight range of angular movements is conventionally divided into three sub ranges. A graph is given of the dependence of the area of the photosensitive surface of a photo resistor made from a single crystal of high-resistivity p-type silicon.

Improvement Of Calorimetric Quality Analyzers For Substances, Makhfuza Azimovna Radjabova

Chemical Technology, Control and Management

It is noted that the development of intelligent means of measuring qualitative indices is of topical importance. Since the quality of many substances is determined by optical methods, an algorithm for spectrophotometric data processing has been developed, which consists of primary data processing (stage I) and determination of qualitative indices of liquid products (stage II). Since the task of numerical determination of colour characteristics of transmittance coefficients of liquid samples is incorrectly set, it is recommended to use regularization methods of A.N.Tikhonov to improve metrological characteristics of the device. On the basis of regularization methods for solving incorrect problems, algorithms …

Improvements Of The Control System For The Technological Process Of Drying Bulk Materials, Azizbek Nodirbekovich, Dilmurod Ikromovich

Chemical Technology, Control and Management

The issues of convective drying of bulk materials as objects of monitoring, control and advanced management are presented based on the results of simulation modeling of a complex heat and mass transfer process, taking into account the drying kinetics. As a result of the work of a number of them, in the last few decades neat hypotheses were formed about moisture migration in and around dried materials, which led to the creation of accurate mathematical models of drying behavior, with successfully applied in a wide range of fields. The reasons for this are the dynamics of processes in the drying …

Application Of Quantum Algorithms In The Synthesis Of Dynamic Objects, Noilakhon Yakubova

Chemical Technology, Control and Management

Around the world, the food industry is focusing on achieving energy and resource efficiency. One of the main challenges in the field of process automation is the creation of effective control systems using intelligent technologies to improve the quality of processes and achieve the production of high-quality products with less energy and resources. Therefore, it is necessary to work with a large amount of data. Particular attention is paid to the development of computational algorithms for automated high-speed computational analysis systems for processing this data at high speed. Therefore, the article discusses the use of quantum computing methods in controlling …

System For Advanced Control Of Thermal Parameters Of Glass Furnaces, O'Tkir Xolmanov

Chemical Technology, Control and Management

The results of an analysis of the functioning of glass furnaces for melting semi-white or discolored glass as an object of automatic control and management are presented. Through experimental research, a parametric control scheme for a glass melting furnace was formed and a system for improved control of thermal glass melting processes was synthesized. The proposed system regulates the parameters of a furnace with a horseshoe-shaped flame development. Based on commercially produced instruments and automation equipment that ensure stabilization of thermal conditions of glass melting. The burner block control algorithm provides control over the performance of the gas burner, safety …

Intelligent Decision Support System, Khurshid Salim Ugli Turayev

Chemical Technology, Control and Management

The article studies issues related to the development of intelligent systems located in an environment capable of perceiving this environment and acting autonomously to achieve assigned tasks. To create an intelligent process control system, it is necessary to monitor the mode to ensure high quality of finished products with minimal energy consumption at a given productivity of the entire complex. It is important to have a flow of input data to provide the system with operational information to support decision making.

The proposed intelligent control system makes it possible to analyze the results of production activities to make organizational and …

Life Cycle Management Of A Technological Complex For Separating Multicomponent Mixtures Under Conditions Of Uncertainty Of Parameters, Yusuf Shodievich Avazov

Chemical Technology, Control and Management

The issue of control the lifecycle of technological complexes of multicomponent mixtures is considered, taking into account the uncertainty of parameters. Among uncertainties such as parameter uncertainty, model uncertainty, choice uncertainty under variability, spatial variability uncertainty, temporal variability uncertainty, inter-site variability uncertainty, more attention is paid to input parameter uncertainty and action uncertainty. The rectification technology is schematically presented, the influence of parameter uncertainty on the technological functions of the rectification complex. The scheme analyzes the control and assessment of “uncertainty” to repeat the lifecycle of the rectification complex and make changes to the components of the rectification complex technology. …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, Datu Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

A Systems Approach To Process Design And Sustainability - Synergy Via Pollution Prevention, Control, And Source Reduction, Emmanuel Apau Aboagye

Theses and Dissertations

Historically, process design prioritized efficiency and profitability, often overlooking environmental and societal implications. However, given the global challenges like climate change and resource scarcity, there is a growing emphasis on embedding sustainability into process design. Adopting a systems-oriented approach provides a comprehensive view, spanning from raw material acquisition to end-of-life product management. Such an approach not only identifies potential sustainability challenges but ensures that solutions foster both environmental responsibility and economic viability. In this study, a comprehensive framework for designing industrial systems is introduced, aiming to encompass the entire lifecycle impacts of chemical processes. The research initially delves into two …

Dependence Of The Granulometric Composition Of Chalk During Granulation In A Turbulized Layer, N.A. Annaev, S.Kh. Nurmukhamedov, Zh.V. Sultonov, N.Sh. Khudoiberdieva

Chemical Technology, Control and Management

The article presents the results of an experimental study on chalk granulation in the turbulized layer of a turboblade granulator. The design of the apparatus combines the following sequential processes: grinding, granulating and compacting newly formed granules. In addition, this device has the ability to carry out both rotational and reciprocating motion. It has been established that preliminary grinding of the feedstock increases the efficiency of the granulation process and improves the quality of the finished product. In the experiments, four substances were used to create 2 astringent suspensions and the optimal combination and their ratios were determined. The experiments …

Fast Fourier Transform Analytical Expression Of Estimation Of Nosinusoidality Indicators, Ilkhomjon Khakimovich Siddikov, Zailobiddin Urazali O’G’Li Boixanov

Chemical Technology, Control and Management

This in the article asynchronous motor is reactive power control to do and manage for from the transformer used. The main element of the current transformer is the measuring instrument, i.e. the sensitive element. Depending on the number of asynchronous motor stator blades, the measurement sensitive element is placed between the main winding and the rotor as a two-ring or three-ring. Measurement accuracy, reliability, and sensitivity increase compared to an independent measuring device. The measuring element loops are independent or connected in series . When the measurement loops are connected in series, the amount of output voltage is …

The Algorithm For The Design Of Fine Granular Substances’ Smart-Type Heat And Moisture Converters Based On Their Accuracy And Speed Criteria, Erkin Uljaev, Ali Abduakhatovich Abduraxmanov

Chemical Technology, Control and Management

The paper describes a technique and algorithm allowing to perform parametric design of smart-type heat and moisture converters (hereinafter SHMC) of fine-grained dispersive materials based on their criteria of accuracy and speed. The proposed algorithm optimizes the process of design of smart-type switches and ensure optimal performance of the switches. The method of calculation and selection of optimal parameters of smart-type heat and moisture converters intended to be used in the measurement of parameters such as heat and humidity of fine dispersive substances are aimed at boosting two parameters, i.e., the accuracy and speed. Also, the design stages have been …

Algorithm For The Functioning Of The Robot's Mechatronic System, Nodira Batirdjanovna Alimova, Bekmurod Bayotovich Yusupov

Chemical Technology, Control and Management

Currently, the introduction of mechatronics and robotics into modern technologies, including rural industry, which are based on different types of mechatronic modules, is relevant. The article discusses the functioning algorithm of the electro-pneumatic multi-position mechatronic system of an intelligent robot. The mechatronic system under consideration is an integrated complex of electro-pneumatic elements, electronic elements and computer technology, with constant dynamic changes in energy and information between them, united by a common automatic control system. The main distinctive feature of this mechatronic system is increased positioning accuracy and high traction forces.

Development Of An Imitation Model Of The Vulcanization Process In The Production Of Elastomeric Composites, Toshtemir Avezov, Mirxalil Agzamovich Ismailov

Chemical Technology, Control and Management

In the article, a systematic approach to the mathematical modeling of the production process of complex multi-stage elastomeric composites was considered, which allows to take into account the stoichiometric relationship of the chemical reaction in the process. Based on the chemical reaction occurring in the mixer, a kinetic model of the elastomer composites production process is proposed, which is the basis for obtaining the main functional relationship of the mathematical model for the mixer, the main quality indicator of the process. The proposed systematic approach in the form of a mathematical model based on the stoichiometric relationship and the …