Nuclear Engineering Commons^™

Afci Quarterly Input – Unlv October 1 Through December 31, 2005, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Gamma-Ray Induced Photoconductivity In Pyrex, Quartz, And Vycor, Shoaib Usman, Lubna Shoaib, James N. Anno

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

Results of an experimental investigation are reported on photoconductive response of Pyrex, Quartz and Vycor. This research was conducted as a feasibility study for developing a new gamma dose measurement device based on the principle of photoconductivity. However, data collected in this study are equally valuable for various other applications where these materials are to be used in high radiation field. Our experiments and analyzes indicated that the selected dosimeter materials exhibit photoconductivity and respond to changes in gamma dose rate within a useful range. Pyrex glass suffered radiation damage at a relatively high dose rate of 0.25 Gys/sup -1/. …

High Temperature Heat Exchanger Project: Quarterly Progress Report July 1, 2005 Through September 30, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. The University of California, Berkeley, hosted a UNLVRF HTHX Project quarterly meeting on September 12. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators discussed their research program plan and provided an update on their progress. The next meeting will be in December in Las Vegas, NV hosted by UNLV.

Afci Quarterly Input – Unlv July 1 Through September 30, 2005, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Modeling, Fabrication, And Optimization Of Niobium Cavities Final Phase: Final Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

This final report provides the activities and accomplishments of Modeling, Fabrication, and Optimization of Niobium Cavities – Final Phase. The fluid flow experiments for the etching of the superconducting cavity walls and baffle designs of phase II of the three phases has been completed leading to a MS thesis in December of 2003. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion of the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary …

High Temperature Heat Exchanger Project: Quarterly Progress Report April 1, 2005 Through June 30, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. General Atomics hosted a UNLVRF HTHX Project quarterly meeting on June 5 in San Diego, California. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators had the opportunity to discuss their research program plan and update their progress. The next meeting will be in September in Berkeley hosted by UC Berkeley.

HTHX Computational Design (UNLV). Work on optimizing the ceramic offset strip in compact HTHX design through parametric studies was performed and completed. A simple single channel model was used to perform parametric studies on dimensions and flow …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (March – May 2005), Ajit K. Roy

Transmutation Sciences Materials (TRP)

Accomplishments:

● Analyses of defects (dislocations) in martensitic Alloy EP-823, cold-reduced to different levels, have been performed by using transmission electron microscopy. The dislocation density has been related to the degree of cold-reduction and residual stress in terms of a line-shape parameter determined by the positron annihilation spectroscopy (PAS).

● Additional PAS measurements are ongoing on tensile, welded and cold-worked specimens of Alloys EP-823 and HT-9 at the Idaho Accelerator Center of ISU. Both Subhra and Silpa are involved in these measurements.

● Silpa is performing neutron diffraction (ND) measurements at the Atomic Energy of Canada Limited (AECL), Chalk River …

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (February – April 2005), Ajit K. Roy

Transmutation Sciences Materials (TRP)

This proposal is intended to study the effect of Si content not only on the corrosion resistance but also on the radiation-induced embrittlement of martensitic stainless steels. The susceptibility of these alloys with different Si content to stress corrosion cracking, general corrosion and localized corrosion will be evaluated in the molten LBE and aqueous environments of different pH values using state-of-the-art testing techniques. Testing in the aqueous media is intended to develop baseline data for comparison purpose. Radiation-induced embrittlement of these alloys will initially be studied by irradiating the test specimens with bremmstrahlung gamma radiation from 20-40 MeV electron beams …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing: Quarterly Progress Report #3, Jamil M. Renno, Georg F. Mauer

Fuels Campaign (TRP)

Value Engineering (VE) is used to maximize the product of a process while utilizing the minimum amount of resources. In previous reporting periods a powder processing hot cell was designed and simulated. A VE study will be initiated for this work cell. A manipulator reliability study and a workspace study are performed in this work period. The above noted studies can be combined, and improvements can be made in the operations of the work cell.

Neutron Multiplicity Measurements For The Afci Program Quarterly Progress Report April-June 2005, Denis Beller

Transmutation Sciences Physics (TRP)

This project was developed to test a Russian-built Neutron Multiplicity Detector System (NMDS) for measuring neutrons generated in a central target by a variety of accelerators. To assist in experiment design and evaluation, we use the most advanced high energy radiation transport code, MCNPX, to model experiments. Experimental results are compared to computational predictions and discrepancies are investigated. Initial plans were to conduct experiments using a 70-MeV proton cyclotron at the Crocker Nuclear Laboratory at the University of California at Davis and/or a 20 to 40 MeV electron linac (linear accelerator) at the Idaho Accelerator Center (IAC) at Idaho State …

Reactor Physics Studies For The Afci Race Project: Reactor-Accelerator Coupling Experiments Project: Quarterly Progress Report April-June 2005, Denis Beller

Transmutation Sciences Physics (TRP)

In the RACE Project of the U.S. Advanced Fuel Cycle Initiative (AFCI), a series of accelerator driven subcritical systems (ADSS) experiments is being conducted at the Idaho State University’s Idaho Accelerator Center (ISU-IAC), at will be conducted at the University of Texas (UT) at Austin, and at the Texas A&M University. In these experiments we will use electron accelerators to induce bremsstrahlung photon-neutron reactions in heavy-metal targets; this source of about 10¹² to 10¹³ n/s will then initiate fission reactions in the subcritical systems. These systems will include a compact, transportable assembly at ISU and TRIGA reactors at …

Secondary Electron Emission From Niobium At Cryogenic Temperatures, Anoop George, Robert A. Schill Jr., Richard Kant, Stan Goldfarb

Transmutation Sciences Materials (TRP)

• A Secondary Electron Emission test stand has been designed to study the initial conditions of secondary electrons emitted from niobium in cryogenic state.

• Secondary electron particle distributions have been studied for 0^o, 15^o, and 30^o beveled surfaces

• BCP and EP samples have been compared showing that the EP count is over twice as large as the BCP count

• Electron beam surface conditioning was examined. Conditioning appears to be sensitive to pulse duration and the number of impacts

• Good comparison have been shown between experiment and simulation

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Quarterly Report, April 2005 To June 2005, Earl Wolfram, Thomas Hartmann, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert matrix fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10 % of ²³⁹Pu. Ceramics will be synthesized and characterized based on the reactor physics results. The solubility the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, will be investigated in a manner to …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Neutronic Evaluation Of Zro2-Mgo Inert Fuels, E. Shwageraus, A. Galperin, E. Fridman, S. Kolesnikov

Fuels Campaign (TRP)

This report presents results of the analysis performed within the framework of “Dissolution, Reactor, and Environmental Behavior of ZrO₂-MgO Inert Fuel Matrix” project managed by University of Nevada at Las Vegas, Harry Reid Center for Environmental Studies. The main objective of the study was to explore the basic neutronic feasibility of using MgO-ZrO₂ as inert fuel matrix for Pu recycling in conventional Light Water Reactors (LWR).

Afci Quarterly Input – Unlv April Through June, 2005, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

Quarterly report highlighting research projects, activities and objectives of the Transmutation Research Program at the Nuclear Science & Technology Division, Harry Reid Research Center.

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Neutronic Evaluation Of Zro2-Mgo Inert Fuels, E. Fridman, S. Kolesnikov, E. Shwageraus, A. Galperin

Fuels Campaign (TRP)

This report presents the results of the Task 4, defined in working program as: evaluation of reactivity feedback coefficients. Three main parameters of the Fertile-Free Fuel (FFF) lattices were evaluated: Moderator Temperature Coefficient (MTC), Fuel Temperature Coefficient due to Doppler Effect (DC), and soluble Boron reactivity worth (BW).

One of the major design challenges associated with utilization of FFF is deterioration of the temperature coefficients and control materials reactivity worth caused by high thermal cross-section of Pu and consequent hardening of the neutron spectrum. The purpose of the investigation reported in this section is to estimate the potential of addition …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (December 01, 2004 – February 28, 2005), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed (bent), and welded materials using a nondestructive method based on positron annihilation spectroscopy (PAS). This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens that could not be accomplished by conventional positron technique or other nondestructive methods. The data …

Effect Of Silicon Content On The Corrosion Resistance And Radiation-Induced Embrittlement Of Materials For Advanced Heavy Liquid Metal Nuclear Systems: Quarterly Progress Report (November 2004 – January 2005), Ajit K. Roy

Transmutation Sciences Materials (TRP)

This proposal is intended to study the effect of Si content not only on the corrosion resistance but also on the radiation-induced embrittlement of martensitic stainless steels. The susceptibility of these alloys with different Si content to stress corrosion cracking, general corrosion and localized corrosion will be evaluated in the molten LBE and aqueous environments of different pH values using state-of-the-art testing techniques. Testing in the aqueous media is intended to develop baseline data for comparison purpose. Radiation-induced embrittlement of these alloys will initially be studied by irradiating the test specimens with bremmstrahlung gamma radiation from 20-40 MeV electron beams …

Bimetallic Pt-Ag And Pd-Ag Nanoparticles, Frank D. Blum, Akira Tokuhiro, Massimo F. Bertino, Carmen M. Doudna

Chemistry Faculty Research & Creative Works

We report studies of bimetallic nanoparticles with 15%-16% atomic crystal parameters size mismatch. The degree of alloying was probed in a 2-nm Pt core (smallest attainable core size) of Pt-Ag nanoparticles (completely immiscible in bulk) and 20-nm-diameter Pd-Ag nanowires (completely miscible in bulk). Particles were synthesized radiolytically, and depending on the initial parameters, they assume spherical or cylindrical (nanowire) morphologies. In all cases, the metals are seen to follow their bulk alloying characteristics. Pt and Ag segregate in both spherical and wire forms, which indicates that strain due to crystallographic mismatch overcomes the excess surface free energy in the small …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Fourth Quarterly Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for niobium superconducting cavities. The surface preparation can significantly affect the secondary electron emission yields. Such yields are used in design codes. Current codes use values obtained from niobium samples cleaned by a different means at temperatures other than the operating temperature. Secondary electron emission studies on LANL surface-cleaned niobium are conducted with preliminary data presented in this report at room temperature. Soon studies will be …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry, Morphology, And Surface Preparation: Quarterly Report (January 2005-April 2005), Allen L. Johnson, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

This project has four components:

• The fabrication of a materials test apparatus with unique capabilities,
• Comparative studies of steel corrosion under gas phase conditions comparable to the Lead Bismuth Eutectic (LBE) oxygen control conditions,
• Isotope labeling studies, and
• Collaborative efforts with other workers in the field.

Summary of accomplishments:

• Started occupation of the High Temperature Materials Experimental Facility.
• Presented a paper at the meeting of the American Chemical Society in San Diego in March 13-17.
• Currently reviving the ion beam for implantation experiments.
• Currently analyzing 38 steel samples from the DELTA loop from LANL.

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing: Quarterly Progress Report #2, Jamil M. Renno, Georg F. Mauer

Fuels Campaign (TRP)

This report discusses mainly the fabrication of inert matrix fuels. There are three fabrication routes to obtain inert matrix fuels (IMF). IMF is a dispersion-type fuel in which the actinide phase is distributed as a separate phase in a so called inert matrix. This concept has evolved as one of the most promising in the field of transmutation. The following section discusses each manufacturing route aside.

Residual Stress Characterization In Structural Materials By Destructive And Nondestructive Techniques, Ajit K. Roy, Anand Venkatesh, Vikram Marthandam, Satish Dronavalli, Douglas P. Wells, Ronald Rogge

Mechanical Engineering Faculty Research

Transmutation of nuclear waste is currently being considered to transform long-lived isotopes to species with relatively short half-lives and reduced radioactivity through capture and decay of minor actinides and fission products. This process is intended for geologic disposal of spent nuclear fuels for shorter durations in the proposed Yucca Mountain repository. The molten lead-bismuth-eutectic will be used as a target and coolant during transmutation, which will be contained in a subsystem vessel made from materials such as austenitic (304L) and martensitic (EP-823 and HT-9) stainless steels. The structural materials used in this vessel will be subjected to welding operations and …

Development Of Integrated Process Simulation System Model For Spent Fuel Treatment Facility (Sftf) Design: Quarterly Progress Report January 1-March 31, 2005, Yitung Chen, Sean Hsieh

Separations Campaign (TRP)

The Advanced Fuel Cycle Initiative (AFCI) and Transmutation Research Program-University Participation Program (TRP-UPP) supported by Department of Energy of the United States have been developing many important technologies for the transmutation of nuclear waste to address long-term disposal issues. While successfully embedding AMUSE module into a dedicated System Engineering Model (TRPSEMPro), developed by the Nevada Center for Advanced Computational Methods (NCACM) at the University of Nevada-Las Vegas collaborating with Argonne National Laboratory (ANL), ANL is interested in further simulating the Light Water Reactor (LWR) Spent Fuel Treatment Facility (SFTF) combining commercial process simulation and analysis packages and core calculation of …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Jan. 01 – March. 31, 2005), Yingtao Jiang, Bingmei Fu

Transmutation Sciences Materials (TRP)

We performed data analysis on the data collected from LANL test loop. One student was been hired to perform the data analysis. A new proposal is submitted to TRP program. We have one paper accepted for publication in International Journal of Heat and Mass Transfer, and another paper accepted for oral presentation by IEEE International Symposium of Circuits and Systems for the track Chemical Sensors. A manuscript regarding to the RGA analysis for the calibration of oxygen sensor is on the way.

Theoretical Modeling Of Protective Oxide Layer Growth In Non-Isothermal Lead-Alloys Coolant Systems: Quarterly Progress Report (01/01/05- 03/31/05), Yitung Chen

Transmutation Sciences Materials (TRP)

The goal of the proposed research project is to provide basic understanding of the protective oxide layer behaviors and to develop oxide layer growth models of steels in non-isothermal lead-alloys (lead or lead-bismuth eutectic) coolant systems. It is widely recognized that the corrosiveness of the lead-alloys is a critical obstacle and challenge for which it can be safely used or applied in the nuclear coolant systems. Active oxygen control technique can promote the formation of the “self-healing” oxide films on the structural material surface, drastically reducing steel corrosion and coolant contamination. Many experiments of steels exposed to flowing lead-alloys have …

High Temperature Heat Exchanger Project:Quarterly Progress Report January 1, 2005 Through March 31, 2005, Anthony Hechanova

Publications (NSTD)

Quarterly Collaboration Meeting. Ceramatec, Inc. hosted a UNLVRF HTHX Project quarterly meeting on March 17 in Salt Lake City, Utah. The purpose of the meeting was to promote collaboration and communication among the UNLV Research Foundation partners. Collaborators had the opportunity to discuss their research program plan and update their progress. The next meeting will be in June in San Diego City hosted by General Atomics.

Fundamental Chemistry Of U And Pu In The Tbp-Dodecane-Nitric Acid System: Quaterly Report January - March, 2005, Kenneth Czerwinski, Cynthia-May Gong, Amber Wright

Separations Campaign (TRP)

The speciation of hexavalent U and tetravalent Pu will be examined in the TBP-dodecane-nitric acid systems. This topic is chosen based on data needs for separation modeling identified by the AFCI. Emphasis will be placed on studying the influence of nitrate and acetohydroxamic acid on U and Pu speciation as well as conditions where a third phase forms in the organic phase. The organic phase will be 30% TBP in dodecane. Equal volumes of aqueous and organic phase will be used. The speciation of the actinides in the aqueous and organic phase will be determined by a number of different …

Neutron Multiplicity Measurements For The Afci Program Quarterly Progress Report January-March 2005, Denis Beller

Transmutation Sciences Physics (TRP)

The U.S. Advanced Fuel Cycle Initiative (AFCI) is a program to develop economic and environmental methods to reduce the impact of waste from commercial nuclear fuel cycles. One concept for near-complete destruction of waste isotopes from used nuclear fuel is accelerator driven transmutation. High-power accelerators would be used to produce high-energy charged particles, which then collide with heavy metal targets to create a cascade of neutrons. These neutrons then cause a nuclear chain reaction in subcritical systems. Fission neutrons then transmute fissile waste isotopes as well as other problematic isotopes such as technetium-99 and iodine-129. To design these systems, complex …

Reactor Physics Studies For The Afci Race Project: Reactor-Accelerator Coupling Experiments Project: Quarterly Progress Report January-March 2005, Denis Beller

Transmutation Sciences Physics (TRP)

In the RACE Project of the U.S. Advanced Fuel Cycle Initiative (AFCI), a series of accelerator driven subcritical systems (ADSS) experiments is being conducted at the Idaho State University’s Idaho Accelerator Center (ISU-IAC), at will be conducted at the University of Texas (UT) at Austin, and at the Texas A&M University. In these experiments we will use electron accelerators to induce bremsstrahlung photon-neutron reactions in heavy-metal targets; this source of about 10¹² to 10¹³ n/s will then initiate fission reactions in the subcritical systems. These systems will include a compact, transportable assembly at ISU and TRIGA reactors at …