Nanoscience and Nanotechnology Commons^™

Gan Nanowire Laser For A Universal Atomic Force Microscope Probe: A Computational And Feasibility Study, Neal Wostbrock

Nanoscience and Microsystems ETDs

This thesis attempts to establish the groundwork for integrating a GaN nanowire into an AFM probe resulting in a universal atomic force microscope probe. Previous studies have shown GaN nanowires have stable mechanical properties, can be fabricated at scale with high aspect ratios and very smooth side walls, and have intrinsic lasing capabilities; however, mechanical and lasing capabilities have not yet been integrated into a single AFM probe. Here, we develop and analyze a suspended waveguide optical pumping concept that can be fabricated and applied to an AFM probe cantilever, unlocking full potential of GaN’s optical and mechanical properties as …

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …

Expanding Applications Of The Nano Intravital Device As A Platform For Exploring Tumor Microenvironments, Michael Padgen

Legacy Theses & Dissertations (2009 - 2024)

The tumor microenvironment has been demonstrated to be a key determinant in the progression of cancer. Unfortunately, the mechanisms behind the different microenvironments (cytokine gradients, hypoxia, hypoglycemia, etc) have not been fully elucidated. Identifying these mechanisms can lead to targeted, individualized therapy to prevent metastasis. The Nano Intravital Device (NANIVID) is a microfabricated, implantable device designed to initiate specific microenvironments in vivo so that the time course of the effects can be observed. With both spatial and temporal control over the induced environments, the affected regions of the tumor can be compared to the rest of the tumor. The NANIVID …

Investigation Of Surface Properties For Ga- And N-Polar Gan Using Scanning Probe Microscopy Techniques, Josephus Daniel Ferguson Iii

Theses and Dissertations

Because the surface plays an important role in the electrical and optical properties of GaN devices, an improved understanding of surface effects should help optimize device performance. In this work, atomic force microscopy (AFM) and related techniques have been used to characterize three unique sets of n-type GaN samples. The sample sets comprised freestanding bulk GaN with Ga polar and N polar surfaces, epitaxial GaN films with laterally patterned Ga- and N-polar regions on a common surface, and truncated, hexagonal GaN microstructures containing Ga-polar mesas and semipolar facets. Morphology studies revealed that bulk Ga-polar surfaces treated with a chemical-mechanical polish …

High Speed Atomic Force Microscopy Techniques For The Efficient Study Of Nanotribology, James L. Bosse

Master's Theses

As mechanical devices scale down to micro/nano length scales, it is crucial to understand friction and wear at the nanoscale (nanotribology) especially at technically relevant sliding velocities. Accordingly, three novel techniques have been developed to study nanotribology, leveraging recent advances in high speed AFM. The first method utilizes high line-scanning rates coupled with sinusoidal scanning along the AFM fast scan axis, enabling rapid friction measurements as a function of velocity up to 20 mm/sec. The second method rapidly acquires friction versus force curves through disabling the feedback loop during scanning and relating the resulting lateral data with the correspondingly varying …

Nanocharacterization Of Porous Materials With Atomic Force Microscopy, Yasemin Kutes

Master's Theses

Scanning Probe Microscopy techniques have proven very useful in the investigation of porous nanostructured surfaces. Especially, Atomic Force Microscopy (AFM) has been widely used due to its compatibility with non-conducting surfaces. In particular, AFM often complements other techniques like scanning and transmission electron microscopy by providing quantitative surface information coupled with nanoscale spatial resolution. Its ability to operate in fluid is also important, as this allows researchers to mimic the physiological environment of biological materials and systems. In this work, two main types of porous materials are studied with AFM, including Phosphoric Acid Fuel Cell (PAFC) electrode catalyst layers, and …

Microscopic And Spectroscopic Analysis Of Wo3 And Ti-Doped Wo3 Thin Films, Young Taek Yun

Open Access Theses & Dissertations

Tungsten oxide (WO3) has been a subject of high interest for its unique properties, and recently for its importance in different types of industrial applications which ranges from non-emissive displays, optical, microelectronic, catalytic/photocatalytic, humidity, temperature, gas, and biosensor devices. In this study, WO3 and Ti doped thin films were prepared using radio frequency magnetron reactive sputtering at different substrate temperatures ranging from room temperature to 500 ºC in increments of 100 ºC. After forming a hypothesis based on knowledge of established WO3 properties, we attempt in this work to investigate how the doping influences the roughness and the mean grain …

The Characterization And Analysis Of In-Vitro And Elevated Temperature Repassivation Of Ti-6al-4v Via Afm Techniques, Aaron J. Guerrero

Master's Theses

ABSTRACT

The Characterization and Analysis of In-vitro and Elevated Temperature Repassivation of

Ti-6Al-4V via AFM Techniques

Aaron J Guerrero

Research in the corrosion of orthopaedic implants is a growing research field where implants have been known to show adverse effects in patients who have encountered the unfortunate dissolution of their implants due to corrosion. Once corrosion begins within the body, many adverse biological reactions can occur such as late on-set infections resulting in severe health complications. The focus of this research is specifically related to the problem of late on-set infections caused by localized corrosion of orthopaedic implants. In medical …