Nanoscience and Nanotechnology Commons^™

Modulated Nanopores Using Pulse Anodization On Thin Aluminum, Mahesh Babu Gunukula

UNLV Theses, Dissertations, Professional Papers, and Capstones

Nanoporous anodic aluminum oxide has traditionally been made in one of two ways: "Mild Anodization (MA)" or "Hard Anodization (HA)". The former method produces self-ordered pore structures but it is slow and only works for a narrow range of processing conditions; the latter method, which is widely used in the aluminum industry, is faster but it produces films with disordered pore structures. Here we report a novel approach termed "pulse anodization" that combines the advantages of the MA and HA processes. By designing the pulse sequences it is possible to control both the composition and pore structure of the anodic …

Magnetic Sensors For Biodetection, Pranjali Vineet Sneha Deshpande

UNLV Theses, Dissertations, Professional Papers, and Capstones

The objective of thesis is to design magnetic sensor for detection of nanoparticles. Recently integrating the standard laboratory techniques into integrated system on chip is growing attention. Recent development is to combine magnetic markers and magnetoresistive sensors together in magnetic chip. In this thesis two magnetoresistive sensors were studied and designed.

By applying magnetic fields, magnetic nanoparticles can be manipulated on-chip, which can be utilized to pull the molecules to specific binding sites or to test the binding strength and distinguish between specifically and non-specifically bound molecules

Magnetoresistive sensors are compatible with the semiconductor industry which provides electronic signal directly …

Patterning And Characterization Of Carbon Nanotubes Grown In A Microwave Plasma Enhanced Chemical Vapor Deposition Chamber, Mauricio Kossler

Theses and Dissertations

This research studies the growth of carbon nanotubes (CNT) from a nickel catalyst to be used on a field emission device. This thesis can be divided into three sections: the construction of a vacuum chamber for field emission testing, the design and fabrication of a triode structure to enable improved electron emission, and the pretreatment and growth of CNTs. To experimentally test the field emission of CNTs, a vacuum chamber must attain a vacuum of at least 10^-5 torr. Our vacuum chamber designed and built achieved a maximum, final pressure of 10^-8 torr. A triode structure was designed …

Spectroscopic Investigation Of Palladium-Copper Bimetallic Systems For Pem Fuel Cell Catalysts, Timo Hofmann

UNLV Theses, Dissertations, Professional Papers, and Capstones

One of the main barriers to commercialization of polymer electrolyte membrane fuel cells systems is cost, which is largely due to the need of platinum (Pt)-containing catalysts. In this thesis we investigate bimetallic systems consisting of a base metal (copper) and a noble metal (palladium) that, as an alloy on the nanoscale, mimic the electronic properties that make Pt desirable as a catalyst.

We present a detailed investigation of the electronic structure of carbon-supported Pd/Cu nanoparticle catalysts, model bilayer thin film systems, alloys, and various metal reference samples. We have investigated the valence band structure of the catalysts using a …

A Study Of Cantilever-Free Instrumentation For Nanoscale Magnetic Measurements, Bruce Adair Altemus

Legacy Theses & Dissertations (2009 - 2024)

The evolution of the Atomic Force Microscope (AFM) into the Magnetic Force Microscope (MFM) and Magnetic Resonance Force Microscope (MRFM) has had a substantial impact on the characterization of nanoscale phenomena. Detection of 10-17 Newtons per root Hertz has occurred with use of an ultra-sensitive cantilever along with optical interferometry methods within these geometries. The sensitivity of these platforms is dependent on the characteristics of the cantilever, where increased length and a low Young's modulus increase the force sensitivity (meters/Newtons). Using IC fabrication techniques, the realization of generating cantilevers with this sensitivity is feasible, but stress compensation layers are required …

Metal Induced Crystallization Of Silicon Thin Films, Sandeep Kumar Raju Sangaraju

UNLV Theses, Dissertations, Professional Papers, and Capstones

Low temperature crystallization of thin film silicon is important for many industrial applications including flat panel displays and silicon thin film solar cells. Unfortunately this remains a major challenge since crystallization temperature of silicon is above 1,000 degrees Celsius, thus limiting to substrates that can tolerate high temperatures. The inability to deposit crystalline thin films on glass substrates is the reason why flat panel display industry uses amorphous silicon for LCD active matrix displays. Thus the ability to deposit crystallized thin film silicon at low temperatures will have significant impact on thin film silicon applications. It has been observed that …