Open Access. Powered by Scholars. Published by Universities.®
Nanoscience and Nanotechnology Commons™
Open Access. Powered by Scholars. Published by Universities.®
- Publication
Articles 1 - 4 of 4
Full-Text Articles in Nanoscience and Nanotechnology
Contact Resistance Study Of Noble Metals And Alloy Films Using A Scanning Probe Microscope Test Station, Lei Chen, H. Lee, Z. J. Guo, Nicol E. Mcgruer, K. W. Gilbert, S. Mall, Kevin D. Leedy, George G. Adams
Contact Resistance Study Of Noble Metals And Alloy Films Using A Scanning Probe Microscope Test Station, Lei Chen, H. Lee, Z. J. Guo, Nicol E. Mcgruer, K. W. Gilbert, S. Mall, Kevin D. Leedy, George G. Adams
George G. Adams
The proper selection of electrical contact materials is one of the critical steps in designing a metal contact microelectromechanical system (MEMS) switch. Ideally, the contact should have both very low contact resistance and high wear resistance. Unfortunately this combination cannot be easily achieved with the contact materials currently used in macroswitches because the available contact force in microswitches is generally insufficient (less than 1 mN) to break through nonconductive surface layers. As a step in the materials selection process, three noble metals, platinum (Pt), rhodium (Rh), ruthenium (Ru), and their alloys with gold (Au) were deposited as thin films on …
A Parameter Study Of Separation Modes Of Adhering Microcontacts, Yan Du, George G. Adams, Nicol E. Mcgruer, Izhak Etsion
A Parameter Study Of Separation Modes Of Adhering Microcontacts, Yan Du, George G. Adams, Nicol E. Mcgruer, Izhak Etsion
George G. Adams
A finite element model was developed to study adhesion of elastic-plastic microcontacts in a previous investigation. An interesting result was the identification of two distinct separation modes, i.e. brittle and ductile separation. In the current study, that model is used to conduct a series of simulations to determine the influence of four nondimensional parameters (including the maximum load parameter) on the contact and on the separation modes. The results show that the parameter S (the ratio of the theoretical stress to the hardness) and δƒ/δc (representing the loading level) are the most important. Smaller S can only lead to brittle …
Contact Resistance Study Of Noble Metals And Alloy Films Using A Scanning Probe Microscope Test Station, Lei Chen, H. Lee, Z. J. Guo, Nicol E. Mcgruer, K. W. Gilbert, S. Mall, Kevin D. Leedy, George G. Adams
Contact Resistance Study Of Noble Metals And Alloy Films Using A Scanning Probe Microscope Test Station, Lei Chen, H. Lee, Z. J. Guo, Nicol E. Mcgruer, K. W. Gilbert, S. Mall, Kevin D. Leedy, George G. Adams
Nicol E. McGruer
The proper selection of electrical contact materials is one of the critical steps in designing a metal contact microelectromechanical system (MEMS) switch. Ideally, the contact should have both very low contact resistance and high wear resistance. Unfortunately this combination cannot be easily achieved with the contact materials currently used in macroswitches because the available contact force in microswitches is generally insufficient (less than 1 mN) to break through nonconductive surface layers. As a step in the materials selection process, three noble metals, platinum (Pt), rhodium (Rh), ruthenium (Ru), and their alloys with gold (Au) were deposited as thin films on …
A Parameter Study Of Separation Modes Of Adhering Microcontacts, Yan Du, George G. Adams, Nicol E. Mcgruer, Izhak Etsion
A Parameter Study Of Separation Modes Of Adhering Microcontacts, Yan Du, George G. Adams, Nicol E. Mcgruer, Izhak Etsion
Nicol E. McGruer
A finite element model was developed to study adhesion of elastic-plastic microcontacts in a previous investigation. An interesting result was the identification of two distinct separation modes, i.e. brittle and ductile separation. In the current study, that model is used to conduct a series of simulations to determine the influence of four nondimensional parameters (including the maximum load parameter) on the contact and on the separation modes. The results show that the parameter S (the ratio of the theoretical stress to the hardness) and δƒ/δc (representing the loading level) are the most important. Smaller S can only lead to brittle …