Open Access. Powered by Scholars. Published by Universities.®

Nanoscience and Nanotechnology Commons™

Open Access. Powered by Scholars. Published by Universities.®

Journal

Materials Science and Engineering

2005

Articles 1 - 10 of 10

Full-Text Articles in Nanoscience and Nanotechnology

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li Nov 2005

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li

Journal of Electrochemistry

The electrochemical behavior of 3,4-Dihydroxybenzoic acid(DHBA)on modified multiply wall carbon nanotubes electrode was investigated by cyclic voltammetry(CV) and square wave voltammetry(SWV).Results show that in 0.1 mol/L HCl solutions the modified carbon nanotube electrode has an obvious electrocatalytic effect on the oxidation and deoxidization of DHBA.The oxidation current of DHBA is linear to it's concentration in the range of 4.0×10~(-6)～1.0×10~(-4) mol/L and 2.0×10~(-4)～8.0×10~(-4)1mol/L with correlation coefficient of 0.9995 and 0.9992.The detection limit is 1.0 ×10~(-6)mol/ L.

Go to article

The Research Of Nano-Sized Nio Anode Materials For Lithium Ion Batteries, Jun-Mei Yan, Jing Zhang, Yong Yang Aug 2005

The Research Of Nano-Sized Nio Anode Materials For Lithium Ion Batteries, Jun-Mei Yan, Jing Zhang, Yong Yang

Journal of Electrochemistry

The nano-sized NiO materials were synthesized by solid phase method and sol-gel method. The synthesis conditions were optimized by DSC and TG techniques. The sol-gel method was optimized by changing the solvent and regulating the solution's pH for preparing NiO material. The structure and morphology of the materials were also characterized by means of XRD and TEM techniques, and the electrochemical performances of the materials were studied by the galvanostatically charge and discharge experiments.

Go to article

Cyclic Voltammetry And Surface Enhanced Raman Spectroscopy Of Dissociative Adsorption Of Ethanol On Pt-Ru Electrodes, Zhang Bin Aug 2005

Cyclic Voltammetry And Surface Enhanced Raman Spectroscopy Of Dissociative Adsorption Of Ethanol On Pt-Ru Electrodes, Zhang Bin

Journal of Electrochemistry

The behaviors of dissociative adsorption of ethanol on roughened platinum-ruthenium electrode with high activity of SERS were studied by using cyclic voltammetry and in-situ surface enhanced Raman spectroscopy, surface enhanced Raman spectra of dissociative adsorption of ethanol on Pt electrode in acid was obtained for the first time. It is shown that the Pt-Ru could lower the over-potential of CO oxidation when compared to Pt electrode. The results show that the ethanol in acid medium can be self-dissociated at Pt-Ru electrode to produce CO, which discourage the further oxidation of ethanol, some information of Pt-C and Pt-C-Pt stretching vibration from …

Go to article

Surface-Enhanced Raman Spectra Of Cytosine Adsorbed On A Roughened Gold Electrode, Yuan-Fei Wu, Jian-Feng Li, De-Yin Wu, Bin Ren, Zhong-Qun Tian Aug 2005

Surface-Enhanced Raman Spectra Of Cytosine Adsorbed On A Roughened Gold Electrode, Yuan-Fei Wu, Jian-Feng Li, De-Yin Wu, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

Cytosine adsorbed on a roughened gold electrode has been investigated by using electrochemical cyclic voltammetry and surface-enhanced Raman spectroscopy (SERS). The results indicate that cytosine was adsorbed on the Au electrode in a perpendicular orientation via the N3 position. As the maximum enhancement of ring breathing mode appears at negative potentials compared with other modes, both the electromagnetic enhancement and the charge transfer mechanism were considered to contribute to the SERS intensity. The binding interaction between cytosine and the gold electrode was weakened when the potential was negatively moved. The result also indicates that the SERS technique can be used …

Go to article

Surface And Sructure Investigations Of Membrane Electrode Assembly In Dmfc Lifetime Testing~*, Chengxuan Chengxuan, Cheng Peng, Meng-Di You, Jing Liu, Ying Zhang Aug 2005

Surface And Sructure Investigations Of Membrane Electrode Assembly In Dmfc Lifetime Testing~*, Chengxuan Chengxuan, Cheng Peng, Meng-Di You, Jing Liu, Ying Zhang

Journal of Electrochemistry

The lifetime and performance of a direct methanol fuel cell (DMFC) were investigatedto understand the correlation between thestructure of catalysts /membrane and cell performanceversus time.The cell polarization and performance curves were obtained during the DMFC operation with the time.The catalysts and Nafion~ membrane of the membrane electrode assembly (MEA) from the lifetime test were comprehensively examined by XRD, HRTEM, FTIRand Raman spectroscope techniques.The results revealed that there was significant performance degradation during the first 200 hours operation; while the degradation was slowing down between 200 and 704hours operation.The degradation became worse after 1 002 h operation.The increases of the catalyst …

Go to article

The Application Of Astm C1202-93 On Evaluating The Performance Of Anti-Corrosion Of Concrete, Yuan Chen Yuan Aug 2005

The Application Of Astm C1202-93 On Evaluating The Performance Of Anti-Corrosion Of Concrete, Yuan Chen Yuan

Journal of Electrochemistry

The test of chloride ion penetration based on the standards of ASTM C1202-93 is applied to evaluate the anti-corrosion performance of concrete in this research. Concrete specimens were produced according to ACI 318-89 mixture proportioning design and the Desenfied Mixture Design Algorithm (DMDA) and were measured the 6-hour coulombs at the age of 91 days. Results show that w/b is not the factor influencing chloride penetration of ACI concrete, as the ion penetration of ACI specimens is all higher than 2 000 Coulombs and can even be poorer than 10 000 Coulombs. With a proper amount of pozzolanic material, the …

Go to article

Electrocatalytic Oxidation And Degration Of Active Red X-3b By Nanotubes Catalytic Electrodes, Yi Wen, Jian-Hui Fang Aug 2005

Electrocatalytic Oxidation And Degration Of Active Red X-3b By Nanotubes Catalytic Electrodes, Yi Wen, Jian-Hui Fang

Journal of Electrochemistry

The catalytic splitting decomposition of carbon nanotubes isprocessed by dispersing with dilute nitric acid and thermal oxidation. Then well-proportionedphenolic resin is mixed in the carbon nanotubes. Then, the carbon nanotubesare made into electrodes by hot-press molding after the process of milling with high speed. The surface of the carbon nanotubes electrodes is analyzed by SEM. Active red X-3B simulated waster water is disposed by carbon nanotubes catalyticelectrode (anode) and stainless steel(cathode). The influencing factors of degradation by current density, concentrationof electrolyte, systemtemperature and pH are investigated. The experimental results indicated that acidiccondition is propitious tothe degradationreaction of organicdyestuff and wastewater …

Go to article

Preparation, Characterization And Electrochemical Properties Of Nano Tio_(2)-Cnt-Pt On Ti Substrate Complex Electrode, Dao-Bao Chu May 2005

Preparation, Characterization And Electrochemical Properties Of Nano Tio_(2)-Cnt-Pt On Ti Substrate Complex Electrode, Dao-Bao Chu

Journal of Electrochemistry

The nanoTiO_(2)-CNT-Pt on Ti substrate complex electrodes were prepared from precursor of (Ti(OEt)_(4)) directly hydrolyzed and by cyclic voltammograms electroplating method . The XRD and SEM results showed that the nano TiO_(2) (anatase) particle sizes ranged 5~10 nm and the Pt nanoparticle (average size 9nm) dispersed uniformly on nanoTiO_(2)-CNT film surface. The electrocatalytic activity of Ti/nanoTiO_(2)-CNT-Pt electrode was investigated by cyclic voltammetry and chronopotentiogram. The results indicated that the Ti/nanoTiO_(2)-CNT-Pt electrode exhibited very high electrocatalytic activity and stability for the electro-oxidation of methanol at room temperature. When Pt loading was 0.32 mg/cm~(2), the oxidation peak current of methanol was 480 …

Go to article

Using Electrodeposition To Fabricate Mould For Polymer Microfluidic Chip, Luo Yi May 2005

Using Electrodeposition To Fabricate Mould For Polymer Microfluidic Chip, Luo Yi

Journal of Electrochemistry

Many researches have been focused on polymer microfluidic chip in recent years and the mould plays an important role in its fabrication process. Using electrodepositingmethod to fabricate a metal mould for polymer microfluidic chip has been presented in this paper. An ultra-thick photoresist SU-8 was coated on a pretreated metal plate, after photolithography, nickel was electrodeposited in the patterned SU-8, then was removed the SU-8 to obtain a final metal mould. This methodreduces workload of electrodeposit largely. Applying counter current before deposit, adding additive to solution and vacuum anneal after demould have been used to improve the binding force between …

Go to article

The Fabrication And Electrochemical Studies On Carbon Nanotube Array Electrodes, Quan-Yong Gao, Jing Zhang, Yangyong Yangyong Feb 2005

The Fabrication And Electrochemical Studies On Carbon Nanotube Array Electrodes, Quan-Yong Gao, Jing Zhang, Yangyong Yangyong

Journal of Electrochemistry

An improved technique for fabrication of carbon nanotube array electrodes has been proposed in this work. Firstly, carbon nanotubes (CNs) array electrodes were prepared by combsination of Chemical Vapor Decomposition (CVD) method and sputtering techniques in anodized aluminum oxide (AAO) membrane. The CNs/AAO was immersed into HF solution to remove the barrier layer. Controlling the immersing time, the CNs array electrodes with different length contacted with electrolyte can be prepared. The morphology of CNs array electrodes was observed by SEM. The electrochemical properties of CNs array electrodes were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Cyclic voltammetric curves of …

Go to article