Nanoscience and Nanotechnology Commons^™

Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Pd Doped Sno2 Resistive Film As A Non-Enzymatic Glucose Sensor, Salim F. Bamsaoud, Sandhya Rani, R. N. Karekar Prof., S. W. Gosavi

Hadhramout University Journal of Natural & Applied Sciences

A new sugar sensor based on metal oxide is presented here. The variation on the sensor resistance is studied against different glucose and fructose concentrations (1 - 360 mg/dl). The study is done for three different resistive films (i) pristine palladium oxide (PdOx); (ii) tin oxide (SnO2) and (iii) palladium doped tin oxide (Pd-SnO2). The chemical reactions of glucose and fructose with surface species were studied. Pd-SnO2 films show an excellent and reliable response to glucose and fructose solution in comparison with the bare films (PdOx and SnO2). Sensor performance was checked for the blood of normal (120 mg/d) and …

Dreams Of Molecular Beams: Indium Gallium Arsenide Tensile-Strained Quantum Dots And Advances Towards Dynamic Quantum Dots (Moleculare Radiorum Somnia: Indii Gallii Arsenicus Tensa Quanta Puncta Et Ad Dinamicae Quantae Puntae Progressus), Kevin Daniel Vallejo

Boise State University Theses and Dissertations

Through the operation of a molecular beam epitaxy (MBE) machine, I worked on developing the homoepitaxy of high quality InAs with a (111)A crystallographic orientation. By tuning substrate temperature, we obtained a transition from a 2D island growth mode to step- ow growth. Optimized MBE parameters (substrate temperature = 500 °C, growth rate = 0.12 ML/s and V/III ratio ⩾ 40) lead to growth of extremely smooth InAs(111)A films, free from hillocks and other 3D surface imperfections. We see a correlation between InAs surface smoothness and optical quality, as measured by photoluminescence spectroscopy. This work establishes InAs(111)A as a platform …

Reliability Characterization Of A Low-K Dielectric Using Its Magnetoresistance As A Diagnostic Tool, Philip Alister Williams

Legacy Theses & Dissertations (2009 - 2024)

The introduction of low dielectric constant materials within the integrated circuit (IC) chip technology industry was a concerted effort to decrease the resistance-capacitance (RC) time delay inherent within the dielectric materials used as insulators. This stems from a demand for greater device density per IC chip and decreased feature sizes but is fast becoming a reliability issue. Concomitant with the demand for decreased feature sizes, also in adherence with Moore’s Law (which states that the number of devices on a die doubles every two years), is a reduction in device speed and performance due to device intra-level interconnection signal delays. …

Twisted Laminar Superconducting Composite: Mgb2 Embedded Carbon Nanotube Yarns, Ujjal Lamichhane, Gamage C. Dannangoda, Mkhitar Hobosyan, R. A. Shohan, A. Zakhidov, Karen S. Martirosyan

Physics and Astronomy Faculty Publications and Presentations

Twisted laminar superconducting composite structures based on multi-wall carbon nanotube (MWCNT) yarns were crafted by integrating magnesium and boron homogeneous mixture into the carbon nanotube (CNT) aerogel sheets. After the ignition of the Mg–B–MWCNT system, under the controlled argon environment, the high exothermic reaction between magnesium (Mg) and boron (B) with stoichiometric ratio produced the MgB2@MWCNT superconducting composite yarns. The process was conducted under the controlled argon environment and uniform heating rate in the differential scanning calorimetry and thermogravimetric analyzer. The XRD analysis confirmed that the produced composite yarns contain nano and microscale inclusions of superconducting phase of MgB2. The …

The Profound Photophysical Effects Of Organic Chromophore Connectivity And Coupling, David J. Walwark Jr

Nanoscience and Microsystems ETDs

Through-bond and through-space interactions between chromophores are shown to have wide-ranging effects on photophysical outcomes upon light absorption in organic molecules. In collapsed poly(3-hexylthiophene), through-space coupling creates hybrid chromophores that act as energy sinks for nearby excitons and favorable sites for molecular oxygen to dock. Upon excitation with visible light the highly-coupled chromophores react with the docked oxygen and subsequently do not quench nearby excitons as efficiently. In tetramer arrays of perylene diimide chromophores the central moiety through-bond connectivity is synthesized in two variants which exhibit vastly different single-molecule blinking behavior and theoretically-predicted electronic transition character. In the more-connected tetramer …

Modeling And Simulation Of Janus-Like Nanoparticles Formation By Solid-Gas Exothermic Reactions, A. A. Markov, Karen S. Martirosyan

Physics and Astronomy Faculty Publications and Presentations

Theoretical model for the simulation of synthesis of Janus-like particles (JP) consisting two different phases using the Carbon Combustion Synthesis of Oxides (CCSO) is presented. The model includes the variation of sample initial porosity, carbon concentration and oxygen flow rate used to predict the formation of JP features. The two temperature (2T) combustion model of chemically active submicron-dispersed mixture of two phases including ferroelectric and ferromagnetic was implemented and assessed by using the experimentally estimated activation energy of 112±3.3 kJ/mol and combustion temperature. The experimental values allowed to account the thermal and concentration expansion effect along with the dispersion by …

Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A method of making passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes forming a three-dimensional microscopic optical structure on a cleaved tip of an optical fiber that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Tailoring Plasmon Excitations In Alpha − T 3 Armchair Nanoribbons, Andrii Iurov, Liubov Zhemchuzhna, Godfrey Gumbs, Danhong Huang, Paula Fekete, Farhana Anwar, Dipendra Dahal, Nicholas Weekes

Publications and Research

We have calculated and investigated the electronic states, dynamical polarization function and the plasmon excitations for α − T ₃ nanoribbons with armchair-edge termination. The obtained plasmon dispersions are found to depend significantly on the number of atomic rows across the ribbon and the energy gap which is also determined by the nanoribbon geometry. The bandgap appears to have the strongest effect on both the plasmon dispersions and their Landau damping. We have determined the conditions when relative hopping parameter α of an α − T ₃ lattice has a strong effect on the plasmons which makes our material distinguished …

Molecular Dynamics Simulations Of Self-Assemblies In Nature And Nanotechnology, Phu Khanh Tang

Dissertations, Theses, and Capstone Projects

Nature usually divides complex systems into smaller building blocks specializing in a few tasks since one entity cannot achieve everything. Therefore, self-assembly is a robust tool exploited by Nature to build hierarchical systems that accomplish unique functions. The cell membrane distinguishes itself as an example of Nature’s self-assembly, defining and protecting the cell. By mimicking Nature’s designs using synthetically designed self-assemblies, researchers with advanced nanotechnological comprehension can manipulate these synthetic self-assemblies to improve many aspects of modern medicine and materials science. Understanding the competing underlying molecular interactions in self-assembly is always of interest to the academic scientific community and industry. …

Colloidal Quantum Dot (Cqd) Based Mid-Wavelength Infrared Optoelectronics, Shihab Bin Hafiz

Dissertations

Colloidal quantum dot (CQD) photodetectors are a rapidly emerging technology with a potential to significantly impact today’s infrared sensing and imaging technologies. To date, CQD photodetector research is primarily focused on lead-chalcogenide semiconductor CQDs which have spectral response fundamentally limited by the bulk bandgap of the constituent material, confining their applications to near-infrared (NIR, 0.7-1.0 um) and short-wavelength infrared (SWIR, 1-2.5 um) spectral regions. The overall goal of this dissertation is to investigate a new generation of CQD materials and devices that advances the current CQD photodetector research toward the technologically important thermal infrared region of 3-5 ?m, known as …

Transport, Photoluminescence & Photoconduction Characteristics Of Free Standing Two-Dimensional Γ-Alumina & Titanium Superlattice Doped Two-Dimensional Γ-Alumina Grown By Graphene-Assisted Atomic Layer Deposition, Elaheh Kheirandish

Theses and Dissertations

This study presents a facile high-yield bottom-up fabrication, morphology, crystallographic and optoelectronic characterization of free-standing quasi-2D γ-alumina, a non van der Waals 2D material. The synthesis comprises a multi-cycle atomic layer deposition (ALD) of amorphous alumina on a porous interconnected graphene foam as a growth scaffold and removed next by annealing and sintering the alumina/graphene/alumina sandwich at ~ 800 °C in air . The crystallographic and structural characteristics of the formed non-van der Waals quasi 2D γ-alumina were studied by X-ray diffraction (XRD), selected area electron diffraction (SAED), and high-resolution transmission electron microscopy (HRTEM). This analysis revealed the synthesized 2D …

Simulation Of Light Propagation Captured By Photoemission Electron Microscopy (Peem), Nabila Islam

Dissertations and Theses

The Photoemission electron microscopes (PEEM) is a powerful tool capable of synchronously imaging wave nature of light manifested by interference patterns as well as its particle nature through the energy exchange between the incident photons and the photoemitted imaging electrons. PEEM offers a non-invasive high-resolution approach for studying light propagation and interaction phenomena within a nanophotonic waveguide [7,8]. The electric field intensity variation of the interference pattern yielded by the interaction between the incident light and the guided mode coupled into the waveguide produces varying photoemission yields creating contrast in PEEM image. The guided modes cannot be excited simply by …

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Mathematical Model For Measuring The Concentration Of Nanoparticles In A Liquid During Sedimentation, Safaa Mohammed Ridha Hussien Hussien, Airat Sakhabutdinov, Vladimir Anfinogentov, Maxim Danilaev, Vladimir Kuklin, Oleg Morozov

Karbala International Journal of Modern Science

Expanding the application areas of polymer composite materials with dispersed filler requires the development of technologies providing the required mechanical characteristics. One of these methods is based on forming a thin polymer shell on the surfaces of particles. At the same time, it is impossible to take into account the mechanical characteristics of a thin polymer shell due to its ultra-small thickness. The mechanical properties of the polymer shell can be determined only by indirect methods, and prior information can improve the adequacy of the properties determination. The method, which allows reducing the requirements for composite sample preparation, is proposed. …

Designing Cryogenic Strain Device For 2d Materials, Jake Carter

Mechanical Engineering Undergraduate Honors Theses

The Churchill lab working within the Physics Department at the University of Arkansas is working to create important quantum states including weak topological insulators (TIs) through the use of symmetry engineering and topological electronic states in two-dimensional (2D) crystals of WHM materials. Experimental results of these topological states have been obstructed due to the difficulty to perform controlled in situ strain. This project strives to create a mount to utilize a piezoelectric nanopositioner within cryostats achieving an in situ strain that creates the quantum states the lab is looking to observe. This report also examines the necessary equations to determine …

Statistical And Variational Modeling And Analysis Of Passive Integrated Photonic Devices, Norbert Dinyi Agbodo

Legacy Theses & Dissertations (2009 - 2024)

The success of Si as a platform for photonic devices and the associated availabilityof wafer-scale, ultra-high resolution lithography for Si CMOS has helped lead to the rapid advance of Si-based integrated photonics manufacturing over the past decade. This evolution is nearing the point of integration of Si-based photonics together with Si-CMOS for compact, high speed, high bandwidth, and cost-effective devices. However, due to the sensitive nature of passive and active photonic devices, variations inherent in wafer-based fabrication processes can lead to unacceptable levels of performance variation both within a give die and across a given wafer. Fully understanding the role …

Error Reduction For The Determination Of Transverse Moduli Of Single-Strand Carbon Fibers Via Atomic Force Microscopy, Joshua D. Frey

Theses and Dissertations

The transverse modulus of single strand carbon fibers is measured using PeakForce Atomic Force Microscopy - Quantitative Nanomechanical Measurement to less than 5 percent error for 11 types of carbon fiber with longitudinal moduli between 924-231 GPA, including export-controlled fibers. Statistical methods are employed to improve the quality of data to exclude outliers within an measurement and within the sample set. A positive linear correlation between the longitudinal and transverse modulus with an R²=0.76 is found. Pitch-based fibers exhibit lower measurement error than PAN-based fibers, while PAN fibers exhibited no apparent modulus correlation when the Pitch fibers are …

Nebulizer-Based Systems To Improve Pharmaceutical Aerosol Delivery To The Lungs, Benjamin M. Spence

Theses and Dissertations

Combining vibrating mesh nebulizers with additional new technologies leads to substantial improvements in pharmaceutical aerosol delivery to the lungs across therapeutic administration methods. In this dissertation, streamlined components, aerosol administration synchronization, and/or Excipient Enhanced Growth (EEG) technologies were utilized to develop and test several novel devices and aerosol delivery systems. The first focus of this work was to improve the poor delivery efficiency, e.g., 3.6% of nominal dose (Dugernier et al. 2017), of aerosolized medication administration to adult human subjects concurrent with high flow nasal cannula (HFNC) therapy, a form of continuous-flow non-invasive ventilation (NIV). The developed Low-Volume Mixer-Heater (LVMH) …

Surface Acoustic Waves Increase Magnetic Domain Wall Velocity, Anil Adhikari, Shireen Adenwalla

Shireen Adenwalla Papers

Domain walls in magnetic thin films are being explored for memory applications and the speed at which they move has acquired increasing importance. Magnetic fields and currents have been shown to drive domain walls with speeds exceeding 500 m/s. We investigate another approach to increase domain wall velocities, using high frequency surface acoustic waves to create standing strain waves in a 3 micron wide strip of magnetic film with perpendicular anisotropy. Our measurements, at a resonant frequency of 248.8 MHz, indicate that domain wall velocities increase substantially, even at relatively low applied voltages. Our findings suggest that the strain wave …

Generation Of Excited Species In A Streamer Discharge, Shirshak K. Dhali

Electrical & Computer Engineering Faculty Publications

At or near atmospheric pressure, most transient discharges, particularly in molecular gases or gas mixture containing molecular gases, result in a space charge dominated transport called a streamer discharge. The excited species generation in such discharges forms the basis for plasma chemistry in most technological applications. In this paper, we simulate the propagation of streamers in atmospheric pressure N₂ to understand the energy partitioning in the formation of various excited species and compare the results to a uniform Townsend discharge. The model is fully two-dimensional with azimuthal symmetry. The results show a significantly larger fraction of the energy goes …