Nanoscience and Nanotechnology Commons^™

Photoassisted Nanoscale Memory Resistors, Amir Shariffar

Graduate Theses and Dissertations

Memristors or memory resistors are promising two-terminal devices, which have the potential to revolutionize current electronic memory technologies. Memristors have been extensively investigated and reported to be practical devices, although they still suffer from poor stability, low retention time, and laborious fabrication processes.

The primary aim of this project was to achieve a device structure of quantum dots or thin films to address a fundamental challenge of unstable resistive switching behavior in memristors. Moreover, we aimed to investigate the effects of light illumination in terms of intensity and wavelength on the performance of the fabricated memristor. The parameters such as …

Perovskite Thin Films Annealed In Supercritical Fluids For Efficient Solar Cells, Gilbert Annohene

Theses and Dissertations

In the field of photovoltaics, scientists and researchers are working fervently to produce a combination of efficient, stable, low cost and scalable devices. Methylammonium lead trihalide perovskite has attracted intense interest due to its high photovoltaic performance, low cost, and ease of manufacture. Their high absorption coefficient, tunable bandgap, low-temperature processing, and abundant elemental constituent provide innumerable advantages over other thin film absorber materials. Since the perovskite film is the most important in the device, morphology, crystallization, compositional and interface engineering have been explored to boost its performance and stability. High temperatures necessary for crystallization of organic-inorganic hybrid perovskite films …

Gamma-Ray Radiation Effects In Graphene-Based Transistors With H-Bn Nanometer Film Substrates, E. J. Cazalas, Michael R. Hogsed, S. R. Vangala, Michael R. Snure, John W. Mcclory

Faculty Publications

Radiation effects on graphene field effect transistors (GFETs) with hexagonal boron nitride (h-BN) thin film substrates are investigated using 60Co gamma-ray radiation. This study examines the radiation response using many samples with varying h-BN film thicknesses (1.6 and 20 nm thickness) and graphene channel lengths (5 and 10 μm). These samples were exposed to a total ionizing dose of approximately 1 Mrad(Si). I-V measurements were taken at fixed time intervals between irradiations and postirradiation. Dirac point voltage and current are extracted from the I-V measurements, as well as mobility, Dirac voltage hysteresis, and the total number of GFETs that remain …

The Ph Sensing Properties Of Rf Sputtered Ruo2 Thin-Film Prepared Using Different Ar/O2 Flow Ratio, Ali Sardarinejad, Devendra Kumar Maurya, Kamal Alameh

Research outputs 2014 to 2021

The influence of the Ar/O₂ gas ratio during radio frequency (RF) sputtering of the RuO₂ sensing electrode on the pH sensing performance is investigated. The developed pH sensor consists in an RF sputtered ruthenium oxide thin-film sensing electrode, in conjunction with an electroplated Ag/AgCl reference electrode. The performance and characterization of the developed pH sensors in terms of sensitivity, response time, stability, reversibility, and hysteresis are investigated. Experimental results show that the pH sensor exhibits super-Nernstian slopes in the range of 64.33-73.83 mV/pH for Ar/O₂ gas ratio between 10/0-7/3. In particular, the best pH sensing performance, in …

Contact Resistance Study Of Noble Metals And Alloy Films Using A Scanning Probe Microscope Test Station, Lei Chen, H. Lee, Z. J. Guo, Nicol E. Mcgruer, K. W. Gilbert, S. Mall, Kevin D. Leedy, George G. Adams

George G. Adams

The proper selection of electrical contact materials is one of the critical steps in designing a metal contact microelectromechanical system (MEMS) switch. Ideally, the contact should have both very low contact resistance and high wear resistance. Unfortunately this combination cannot be easily achieved with the contact materials currently used in macroswitches because the available contact force in microswitches is generally insufficient (less than 1 mN) to break through nonconductive surface layers. As a step in the materials selection process, three noble metals, platinum (Pt), rhodium (Rh), ruthenium (Ru), and their alloys with gold (Au) were deposited as thin films on …

Contact Resistance Study Of Noble Metals And Alloy Films Using A Scanning Probe Microscope Test Station, Lei Chen, H. Lee, Z. J. Guo, Nicol E. Mcgruer, K. W. Gilbert, S. Mall, Kevin D. Leedy, George G. Adams

Nicol E. McGruer

The proper selection of electrical contact materials is one of the critical steps in designing a metal contact microelectromechanical system (MEMS) switch. Ideally, the contact should have both very low contact resistance and high wear resistance. Unfortunately this combination cannot be easily achieved with the contact materials currently used in macroswitches because the available contact force in microswitches is generally insufficient (less than 1 mN) to break through nonconductive surface layers. As a step in the materials selection process, three noble metals, platinum (Pt), rhodium (Rh), ruthenium (Ru), and their alloys with gold (Au) were deposited as thin films on …