Mining Engineering Commons^™

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, Datu Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Relating Detonation Parameters To The Detonation Synthesis Of Silicon Carbide, Martin Langenderfer, Eric W. Bohannan, Jeremy Lee Watts, William Fahrenholtz, Catherine E. Johnson

Chemistry Faculty Research & Creative Works

Detonation synthesis of silicon carbide (SiC) nanoparticles from carbon liberated by negatively oxygen balanced explosives was evaluated in a 23 factorial design to determine the effects of three categorical experimental factors: (1) cyclotrimethylene-trinitramine (RDX)/2,4,6-trinitrotoluene (TNT) ratio, (2) silicon (Si) additive concentration, and (3) Si particle size. These factors were evaluated at low and high levels as they relate to the detonation performance of the explosive and the solid Si-containing phases produced. Detonation velocity and Chapman-Jouguet (C-J) detonation pressure, which were measured using rate stick plate dent tests, were evaluated. Solid detonation product mass, silicon carbide product concentration, and residual silicon …

Computational Study On The Microscopic Adsorption Characteristics Of Linear Alkylbenzene Sulfonates With Different Chain Lengths On Anthracite Surface, Xuanlai Chen, Guochao Yan, Guang Xu, Xianglin Yang, Jinfa Dong, Zidong Liang, Shuai Wei

Mining Engineering Faculty Research & Creative Works

In order to explore the influence of different lengths of hydrophobic carbon chains on the diffusion characteristics of surfactants on the surface of anthracite, six linear alkyl benzene sulfonates with different hydrophobic carbon chain lengths were selected (mC, m = 8, 10, 12, 14, 16, 18; m represents the numbers of carbon atoms in the hydrophobic carbon chain), and molecular dynamics (MD) simulations were adopted. Models of surfactant-anthracite, surfactant-graphite layer, and water-surfactant-anthracite were constructed. After analyzing a series of properties such as adsorption energy, diffusion coefficient, radial distribution function (RDF), and hydrophobic tail order parameters, it was found that 12C …

Calcite Depression In Bastnaesite-Calcite Flotation System Using Organic Acids, Emmy Muhoza

Graduate Theses, Dissertations, and Problem Reports

Bastnaesite is the primary source of light REEs, namely cerium (Ce), lanthanum (La), praseodymium (Pr), neodymium (Nd), to name a few. Bastnaesite is typically concentrated using the froth flotation beneficiation method. Flotation of bastnaesite suffers from high reagent consumption due to the similar surface characteristics of bastnaesite and associated gangue minerals, including calcite. Additionally, complex stages of high-temperature conditioning are often required to suppress the detrimental impact of dissolved calcium ions on the flotation of bastnaesite. This research seeks to investigate the capabilities of organic acids in the bastnaesite-calcite flotation systems to selectively depress calcite minerals and effectively chelate calcium …

Thin Safety Margin: The Sefor Super-Prompt-Critical Transient Experiments, Ozark Mountains, Arkansas 1970–1971, Jerry Havens, Collis Geren

Arkansas Scholarly Editions

Thin Safety Margin charts the history of SEFOR, a twenty-megawatt reactor that operated for three years in the rural Ozark Mountains of Arkansas as part of an internationally sponsored program designed to demonstrate the Doppler effect in plutonium-oxide-fueled fast reactors. Authors Jerry Havens and Collis Geren draw upon this history to assess the accidental explosion risk inherent in using fast reactors to reduce the energy industry’s carbon dioxide emissions.

If a sufficiently powerful fast-neutron explosion were to cause the containment of a reactor such as SEFOR’s to fail, the reactor’s radiotoxic plutonium fuel could vaporize and escape into the surrounding …

Relating Detonation Parameters To The Detonation Synthesis Of Nanomaterials, Martin Langenderfer

Doctoral Dissertations

“This research investigates the physical and chemical processes that contribute to the detonation synthesis of silicon carbide nanoparticles. Bulk production of SiC nanoparticles through detonation is possible due to pressures achieved over 20 GPa and temperatures over 2000 K as well as quenching rates in excess of 13 billion K/second. These conditions catalyze reaction and bottom-up molecular growth while retaining particles < 100 nm in diameter. In this work, detonation synthesis of SiC was demonstrated by incorporation of polycarbosilane, an SiC precursor material, into an RDX/TNT explosive matrix prior to detonation. Detonation Synthesis of SiC was also accomplished by reacting elemental silicon with carbon liberated by the detonation of negatively oxygen balanced TNT. Hydrodynamic simulation of a 60:40 mass ratio RDX/TNT detonation created conditions thermodynamically suitable to produce cubic silicon carbide within the first 500 nanoseconds after the passage of the detonation wave while carbon remains chemically reactive for molecular formation. Simulations and experimental tests indicated that loading configuration and impedance mismatch of the precursor additives used in detonation synthesis results in conditions in the additives that exceed the accepted detonation pressure of the explosive by greater than three times. Finally, a full factorial experimental design showed increasing silicon concentration, reducing silicon size, and reducing oxygen balance by adjusting the ratio of RDX to TNT decreased the explosives detonation pressure by 20% and increased the soot yield and concentration of SiC observed in the detonation products by 82% and 442% respectively”--Abstract, page iv.

Removal Of Antimony And Bismuth From Copper Electrorefining Electrolyte By Two Proprietary Solvent Extraction Extractants, Andrew Artzer

Masters Theses

"Antimony and bismuth are two of the most problematic impurities in copper electrorefining (ER). Because of this, much research has been done investigating the ways to remove them. Processes that are currently being used industrially include anode additions, liberators, ion exchange (IX), and solvent extraction (SX). Of these, liberators and anode additions are the most common while SX is the least, mostly being used for arsenic removal. There are other methods that have been evaluated, but are not in commercial use. These include the use of various electrolyte additives, and adsorbents such as bentonite clay and heavy metal sulfates.

Two …

Detonation Synthesis Of Alpha-Variant Silicon Carbide, Martin Langenderfer, Catherine E. Johnson, William Fahrenholtz, Vadym Mochalin

Mining Engineering Faculty Research & Creative Works

A recent research study has been undertaken to develop facilities for conducting detonation synthesis of nanomaterials. This process involves a familiar technique that has been utilized for the industrial synthesis of nanodiamonds. Developments through this study have allowed for experimentation with the concept of modifying explosive compositions to induce synthesis of new nanomaterials. Initial experimentation has been conducted with the end goal being synthesis of alpha variant silicon carbide (α-SiC) in the nano-scale. The α-SiC that can be produced through detonation synthesis methods is critical to the ceramics industry because of a number of unique properties of the material. Conventional …

Study On The Surface Features Of Preg-Robbing Carbonaceous Matter During Oxidation Treatment, Mana Pourdasht

Electronic Thesis and Dissertation Repository

Carbonaceous gold ores have the ability to adsorb gold (I) cyanide from leach solutions during processing. This phenomenon, known as preg-robbing, is responsible for poor recoveries as the carbonaceous materials of the ore compete with activated carbon used during the leaching and adsorption phase of processing. Chemical oxidation of carbonaceous materials by different reagents has been utilized to investigate and compare the mechanism of Au (CN)₂ adsorption onto carbonaceous materials prior to and following the treatment.

The procedure for characterization of the carbonaceous materials (plain and modified) in the sample combines the use of several analytical techniques and test …

Method And Apparatus For Jet-Assisted Drilling Or Cutting, David A. Summers, Klaus Woelk, Kenneth Doyle Oglesby, Greg Galecki

Mining Engineering Faculty Research & Creative Works

An abrasive cutting or drilling system, apparatus and method, which includes an upstream supercritical fluid and/or liquid carrier fluid, abrasive particles, a nozzle and a gaseous or low-density supercritical fluid exhaust abrasive stream. The nozzle includes a throat section and, optionally, a converging inlet section, a divergent discharge section, and a feed section.