Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 9 of 9
Full-Text Articles in Mechanical Engineering
A One-Dimensional Analysis Of A Microbial Fuel Cell For Efficient Acetate Removal And Power Density Output, David Rouhani
A One-Dimensional Analysis Of A Microbial Fuel Cell For Efficient Acetate Removal And Power Density Output, David Rouhani
UNLV Theses, Dissertations, Professional Papers, and Capstones
Microbial fuel cells (MFCs) are electrochemical devices that utilize microorganisms to convert organic matter into electrical energy. MFCs have been discussed to have potential application for sustainable wastewater treatment due to their ability to generate electricity while simultaneously treating contaminated water. To optimize MFC performance, numerical models can be used to understand the complex electrochemical and biological processes occurring in the system. In this study, a numerical model was developed to simulate the performance of MFCs under varying operating conditions and to investigate the performance of a MFC for treating wastewater fuel. More specifically, the MFC was modeled to oxidize …
Thermal And Mechanical Numerical Modeling Of Extrusion-Based 3d Printed Reinforced Polymers For Selecting Manufacturing Process Parameters, Sunil Bhandari
Thermal And Mechanical Numerical Modeling Of Extrusion-Based 3d Printed Reinforced Polymers For Selecting Manufacturing Process Parameters, Sunil Bhandari
Electronic Theses and Dissertations
Extrusion-based 3D printing of thermoplastic polymer composites manufactures parts that have nonhomogenous, orthotropic, and process-dependent macro-scale material properties. As a part of the dissertation, research works were carried out to: • improve the interlayer mechanical properties and reduce the orthotropy, • use experimentally homogenized orthotropic material properties to numerically model the mechanical behavior of the non-homogenous orthotropic 3D printed parts, • create an efficient numerical thermal model to predict the process-dependent thermal history of the 3D printed part, and • aid the manufacturing process by selecting a suitable set of processing parameters based on a simplified sequentially coupled thermomechanical model. …
Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger
Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger
Department of Engineering Mechanics: Dissertations, Theses, and Student Research
The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …
3d Infrastructure Condition Assessment For Rail Highway Applications, Teng Wang
3d Infrastructure Condition Assessment For Rail Highway Applications, Teng Wang
Theses and Dissertations--Civil Engineering
Highway roughness is a concern for both the motoring public and highway authorities. Roughness may even increase the risk of crashes. Rail-highway grade crossings are particularly problematic. Roughness may be due to deterioration or simply due to the way the crossing was built to accommodate grade change, local utilities, or rail elevation. With over 216,000 crossings in the US, maintenance is a vast undertaking. While methods are available to quantify highway roughness, no method exists to quantitatively assess the condition of rail crossings. Conventional inspection relies on a labor-intensive process of qualitative judgment. A quantifiable, objective and extensible procedure for …
Analysis Of Technical Energy Losses By Using Simulation, Betrianis Betrianis, Randite Herawan
Analysis Of Technical Energy Losses By Using Simulation, Betrianis Betrianis, Randite Herawan
Makara Journal of Technology
Model is a representation of a system. Through model, it can be easier to forecast and control the changing of each element system. Electricity distribution is also a system. Losses are general problem that exist in a distribution network system. But with the right methods, specifically technical energy losses can be reduced in order to increase the efficiency. By making model of the distribution network, the value of technical energy losses in the whole network as well as in every line can be observed. Simulation can also be used to see all losses reduction alternatives. By comparing results from each …
Integrating Value Stream Mapping And Simulation, Michelle E. Scullin
Integrating Value Stream Mapping And Simulation, Michelle E. Scullin
Theses and Dissertations
An important principle in Lean manufacturing, value stream mapping (VSM) can be helpful in understanding how process flow and information flow affect each other. A VSM is a static picture of a process that allows the user to see where value is added into the value stream. Simulation is used to evaluate the behavioral issues of processes. In a manufacturing realm this means simulation shows how each operation affects other operations so determinations can be made about where bottlenecks or other problems exist in the process. Theoretically, the integration of VSM and Simulation can aide in process improvement by showing …
A Tool Wear Comparative Study In Turning Versus Computer Simulation In 1018 Steel, Woodrow D. Miner
A Tool Wear Comparative Study In Turning Versus Computer Simulation In 1018 Steel, Woodrow D. Miner
Theses and Dissertations
The material removal process uses cutting tools in order to produce the desired shape of the workpiece. Tool wear has been a problem for cutting tools, since cutting tools wear and break. Research has been accomplished in the tool wear field for tool life and more recently tool wear. The computer generation has created a method to simulate the material removal process. These computer simulations model the cutting tool reaction with the workpiece. Many of the simulation models use finite element analysis to calculate the reaction of the cutting tool. Different finite element models are being used throughout the world …
A Finite Element Simulation Of Temperature And Material Flow In Fricton Stir Welding, Mark J. Lasley
A Finite Element Simulation Of Temperature And Material Flow In Fricton Stir Welding, Mark J. Lasley
Theses and Dissertations
The purpose of this research was to use the Transvalor S.A. product, Forge3, to develop a finite element simulation of the friction stir welding process that improves the predictability of temperature evolution and material flow within the plunge portion of the process. Previous modeling created more heating within the billet than experimental results, probably due to the simplification of the simulation with adiabatic boundary conditions. More realistic tooling temperatures were included in this model as these affect heat evolution which is a determining factor in microcrystalline growth. These results were validated by experimental efforts using a billet and tooling instrumented …
The Benefit Of Using Simulation To Improve The Implementation Of Lean Manufacturing Case Study: Quick Changeovers To Allow Level Loading Of The Assembly Line, Jack J. Mcclellan
The Benefit Of Using Simulation To Improve The Implementation Of Lean Manufacturing Case Study: Quick Changeovers To Allow Level Loading Of The Assembly Line, Jack J. Mcclellan
Theses and Dissertations
In today's competitive manufacturing environment, companies are constantly looking for ways to improve. Because of this, many companies are striving to become "lean" by implementing lean manufacturing, which is a difficult process. To aid in the implementation of lean manufacturing, simulation was used to reduce the trial-and-error period of lean manufacturing and find to optimum approach to implement the lean manufacturing principle. In this research, a case study of implementing level loading of the production schedule for BullFrog International, L.C. will be examined. To make it possible to implement level loading, the thermo-former machine at the beginning of the operations …