Mechanical Engineering Commons^™

An Investigation Into The Response Of The Us And Eu5 To The Covid-19 Disease (Convergence Of Two Pandemics: Covid-19 And Ncds), Omar Hassan

Publications and Research

In late December 2019, a coronavirus disease (COVID-19) was identified in Wuhan China. COVID-19 was a result of the novel severe acute respiratory syndrome coronavirus 2 (SARA-CoV-2), which has resulted in a worldwide sudden and substantial increase in hospitalizations for pneumonia with multiorgan disease. As of October 6, 2020, SARS-CoV-2 has affected more than 200 countries, resulting in more than 35 million identified cases with more than 1 million confirmed deaths.

This is a cross-sectional, non-interventional, observational study in patients infected with the novel coronavirus (SARS-CoV-2) or Covid-19, using John Hopkins University database JHU Coronavirus map. The data collected from …

Grow Local Manufacturing Along Us/Mexico Border Region For An Integrated Supply Chain In The Post Covid-19 Era, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications and Presentations

The current coronavirus disease pandemic, plus the strong movement of manufacturing reshoring, provide a unique opportunity for many US regions to grow local manufacturers. This technical note attempts to review the current situation and trend in US manufacturing. We then discuss challenges and necessary steps, such as asset mapping, required to grow local suppliers. Suggestions are then made to support growing local suppliers along the US/Mexico border region.

Open Source High-Temperature Reprap For 3-D Printing Heat-Sterilizable Ppe And Other Applications, Noah G. Skrzypczak, Nagendra G. Tanikella, Joshua M. Pearce

Michigan Tech Publications

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met …

Conversion Of Self-Contained Breathing Apparatus Mask To Open Source Powered Air-Purifying Particulate Respirator For Fire Fighter Covid-19 Response, Benjamin R. Hubbard, Joshua M. Pearce

Michigan Tech Publications

To assist firefighters and other first responders to use their existing equipment for respiration during the COVID-19 pandemic without using single-use, low-supply, masks, this study outlines an open source kit to convert a 3M-manufactured Scott Safety self-contained breathing apparatus (SCBA) into a powered air-purifying particulate respirator (PAPR). The open source PAPR can be fabricated with a low-cost 3-D printer and widely available components for less than $150, replacing commercial conversion kits saving 85% or full-fledged proprietary PAPRs saving over 90%. The parametric designs allow for adaptation to other core components and can be custom fit specifically to fire-fighter equipment, including …

Open Source High-Temperature Reprap For 3-D Printing Heat-Sterilizable Ppe And Other Applications, Noah G. Skrzypczak, Nagendra Gautam Tanikella, Joshua M. Pearce

Michigan Tech Publications

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met …

Parametric Nasopharyngeal Swab For Sampling Covid-19 And Other Respiratory Viruses: Open Source Design, Sla 3-D Printing And Uv Curing System, Nicole Gallup, Adam Pringle, Shane Oberloier, Nagendra Gautam Tanikella, Joshua M. Pearce

Michigan Tech Publications

Access to nasopharyngeal swabs for sampling remain a bottleneck in some regions for COVID19 testing. This study develops a distributed manufacturing solution using only an open source manufacturing tool chain consisting of two types of open source 3-D printing and batch UV curing, and provides a parametric fully free design of a nasopharyngeal swab. The swab was designed using parametric OpenSCAD in two components (a head with engineered break point and various handles), which has several advantages: i) minimizing print time on relatively slow SLA printers, ii) enabling the use of smaller print volume open source SLA printers, iii) reducing …

Additive Manufacturing And How 3d Printing Is Fighting Covid-19, Raghavan Srinivasan, Ahsan Mian, Joy Gockel, Laura M. Luehrmann

Mechanical and Materials Engineering Faculty Publications

This is the fourth installment in the Shelter in Place (SiP) Lecture series. This installment covers the creative ways that 3D printing has supported efforts to combat the pandemic. It covers the basics of what 3D printing is, some of the various creative projects that have used 3D printing to combat the pandemic, among other topics and questions by the pandemic.

A History And Status Of Wind Energy Potential In Arkansas, Pre And Post Covid-19, Will Blasingame

Mechanical Engineering Undergraduate Honors Theses

Historically, wind-generated electricity has been the largest renewable energy sources in the United States. Wind-rich regions like Oklahoma and Texas have fueled growth and sold that electricity to electric utilities located in wind-poor states like Arkansas in the form of Power Purchase Agreements. Future technologies such as Vertical Axis Wind Turbines, small wind turbines, and Tesla turbines designed to generate electricity from wind show promise in unlocking more expensive wind resources in regions like Northwest Arkansas by mitigating concerns about low wind speeds and noise. However, more factors than just feasibility influence the growth of wind power. Governmental policies such …