Mechanical Engineering Commons^™

Performance Of C2H4 Reductant In Activated-Carbon-Supported Mnox-Based Scr Catalyst At Low Temperatures, Guangli Liu, Dongtai Han, Jie Cheng, Yongshi Feng, Wenbin Quan, Li Yang, Kozo Saito

Mechanical Engineering Faculty Publications

Hydrocarbons as reductants show promising results for replacing NH₃ in SCR technology. Therefore, considerable interest exists for developing low-temperature (< 200 °C) and environmentally friendly HC-SCR catalysts. Hence, C₂H₄ was examined as a reductant using activated-carbon-supported MnOx-based catalyst in low-temperature SCR operation. Its sensitivity to Mn concentration and operating temperature was parametrically studied, the results of which showed that the catalyst activity followed the order of 130 °C > 150 °C > 180 °C with an optimized Mn concentration near 3.0 wt.%. However, rapid deactivation of catalytic activity also occurred when using C₂H₄ as the reductant. The mechanism of deactivation was explored and is …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering News (2013-2023)

• Georgia Southern Research Focus Prompts R2 Carnegie Designation

Additive Manufacturing Of Ti6al4v Alloy: A Review, Shunyu Liu, Yung C. Shin

School of Mechanical Engineering Faculty Publications

In this paper, the recent progress on Ti6Al4V fabricated by three mostly developed additive manufacturing (AM) techniques-directed energy deposition (DED), selective laser melting (SLM) and electron beammelting (EBM)-is thoroughly investigated and compared. Fundamental knowledge is provided for the creation of links between processing parameters, resultant microstructures and associated mechanical properties. Room temperature tensile and fatigue properties are also reviewed and compared to traditionally manufactured Ti6Al4V parts. The presence of defects in as-builtAMTi6Al4V components and the influences of these defects on mechanical performances are also critically discussed.

Coordinated Unmanned Aircraft System (Uas) And Ground-Based Weather Measurements To Predict Lagrangian Coherent Structures (Lcss), Peter J. Nolan, James Pinto, Javier González-Rocha, Anders Jensen, Christina N. Vezzi, Sean C. C. Bailey, Gijs De Boer, Constantin Diehl, Roger Laurence Iii, Craig W. Powers, Hosein Foroutan, Shane D. Ross, David G. Schmale Iii

Mechanical Engineering Faculty Publications

Concentrations of airborne chemical and biological agents from a hazardous release are not spread uniformly. Instead, there are regions of higher concentration, in part due to local atmospheric flow conditions which can attract agents. We equipped a ground station and two rotary-wing unmanned aircraft systems (UASs) with ultrasonic anemometers. Flights reported here were conducted 10 to 15 m above ground level (AGL) at the Leach Airfield in the San Luis Valley, Colorado as part of the Lower Atmospheric Process Studies at Elevation—a Remotely-Piloted Aircraft Team Experiment (LAPSE-RATE) campaign in 2018. The ultrasonic anemometers were used to collect simultaneous measurements of …

A Fuzzy Based Model For Standardized Sustainability Assessment Of Photovoltaic Cells, Muath Bani Salim, Dervis Emre Demirocak, Nael Barakat

Mechanical Engineering Faculty Publications and Presentations

In this paper, a new environmental sustainability indicator (ESI) is proposed to evaluate photovoltaic (PV) cells utilizing Life Cycle Analysis (LCA) principles. The proposed indicator is based on a model that employs a fuzzy logic algorithm to combine multiple factors, usually used in multiple LCAs, and produce results allowing a comprehensive interpretation of LCA phase sub-results leading to standardized comparisons of various PV cells. Such comparisons would be essential for policymakers and PV cell manufacturers and users, as they allow for fair assessment of the environmental sustainability of a particular type of PV with multiple factors. The output of the …

Optimal Placement Of Distributed Energy Storage Systems In Distribution Networks Using Artificial Bee Colony Algorithm, Choton K. Das, Octavian Bass, Ganesh Kothapalli, Thair S. Mahmoud, Daryoush Habibi

Research outputs 2014 to 2021

The deployment of utility-scale energy storage systems (ESSs) can be a significant avenue for improving the performance of distribution networks. An optimally placed ESS can reduce power losses and line loading, mitigate peak network demand, improve voltage profile, and in some cases contribute to the network fault level diagnosis. This paper proposes a strategy for optimal placement of distributed ESSs in distribution networks to minimize voltage deviation, line loading, and power losses. The optimal placement of distributed ESSs is investigated in a medium voltage IEEE-33 bus distribution system, which is influenced by a high penetration of renewable (solar and wind) …

Electroactive Artificial Muscles Based On Functionally Antagonistic Core–Shell Polymer Electrolyte Derived From Ps-B-Pss Block Copolymer, Van Hiep Nguyen, Jaehwan Kim, Rassoul Tabassian, Moumita Kotal, Kiwoo Jun, Jung-Hwan Oh, Ji-Myeong Son, Muhammad Taha Manzoor, Kwang Jin Kim, Il-Kwon Oh

Mechanical Engineering Faculty Research

Electroactive ionic soft actuators, a type of artificial muscles containing a polymer electrolyte membrane sandwiched between two electrodes, have been intensively investigated owing to their potential applications to bioinspired soft robotics, wearable electronics, and active biomedical devices. However, the design and synthesis of an efficient polymer electrolyte suitable for ion migration have been major challenges in developing high-performance ionic soft actuators. Herein, a highly bendable ionic soft actuator based on an unprecedented block copolymer is reported, i.e., polystyrene-b-poly(1-ethyl-3-methylimidazolium-4-styrenesulfonate) (PS-b-PSS-EMIm), with a functionally antagonistic core–shell architecture that is specifically designed as an ionic exchangeable polymer electrolyte. The corresponding actuator shows exceptionally …

First Observation Of P-Odd Gamma Asymmetry In Polarized Neutron Capture On Hydrogen, D. Blyth, J. Fry, N. Fomin, R. Alarcon, L. Alonzi, E. Askanazi, S. Baeßler, S. Balascuta, L. Barrón-Palos, Alex Barzilov, J. D. Bowman, N. Birge, J. R. Calarco, T. E. Chupp, V. Cianciolo, C. E. Coppola, C. B. Crawford, K. Craycraft, D. Evans, C. Fieseler, E. Frlež, I. Garishvili, M. T. W. Gericke, R. C. Gillis, K. B. Grammer, G. L. Greene, J. Hall, J. Hamblen, C. Hayes, E. B. Iverson, M. L. Kabir

Mechanical Engineering Faculty Research

We report the first observation of the parity-violating gamma-ray asymmetry A(gamma)(np) in neutron-proton capture using polarized cold neutrons incident on a liquid parahydrogen target at the Spallation Neutron Source at Oak Ridge National Laboratory. A(gamma)(np) isolates the Delta I = 1, S-3(1)-> P-3(1) component of the weak nucleon-nucleon interaction, which is dominated by pion exchange and can be directly related to a single coupling constant in either the DDH meson exchange model or pionless effective field theory… See full text for full abstract.

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering News (2013-2023)

• Governor Breaks Ground on New Engineering and Research Building

Assessment Of Cooling And Heat Transfer Properties Of Quenchants With Matlab, Lemmy Meekisho, Rosa L. Simencio Otero, Jônatas M. Viscaino, D. Scott Mackenzie, George Totten, Lauralice C.F. Canale

Mechanical and Materials Engineering Faculty Publications and Presentations

There is ongoing interest for evaluating the potential of renewable base stocks, such as vegetable oils, to replace petroleum oils as metal quenchants. Perhaps the most critical part of this process is characterizing and comparing the cooling and heat transfer performance of potential quenchant candidates. In this work, cooling curves of two vegetable oils, palm oil and canola oil, were obtained along with a commercially available conventional and an accelerated petroleum quenchant using the so-called Tensi multiple thermocouple probe, with emphasis on the center probe emulating a small probe concept. The lumped-parameter approach was implemented in the MATLAB environment (Mathworks …

College Of Engineering Senior Design Competition Fall 2018, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Quenchant Cooling Curves, Rewetting, And Surface Heat Flux Properties Of Vegetable Oils, Rosa L. Simencio Otero, Jônatas M. Viscaino, Jun Xu, Jianfeng Wu, George Totten, Lauralice C.F. Canale

Mechanical and Materials Engineering Faculty Publications and Presentations

Vegetable oils are currently used for biodegradable and renewable base stocks for quenchant formulation. However, there are relatively few references relating to their true equivalency, or lack thereof, comparative to the quenching performance of petroleum oil-based quenchant formulations. To obtain an overview of the variability vegetable oil quenching performance, the cooling curves and rewetting properties were determined, and the surface heat flux properties were calculated. The vegetable oils that were studied included canola, coconut, corn, cottonseed, palm, peanut, soybean, and sunflower oils. Cooling curves were obtained using the Tensi multiple-surface thermocouple 15 mm diameter by 45 mm cylindrical Inconel 600 …

Experimental Investigation Into The Effects Of Thermal Recuperation On The Combustion Characteristics Of A Non-Premixed Meso-Scale Vortex Combustor, Seyed Ehsan Hosseini, Evan Owens, John Krohn, James Leylek

Faculty Publications - Mechanical Engineering

In small-scale combustors, the ratio of area to the combustor volume increases and hence heat loss from the combustor’s wall is significantly enhanced and flame quenching occurs. To solve this problem, non-premixed vortex flow is employed to stabilize flames in a meso-scale combustion chamber to generate small-scale power or thrust for propulsion systems. In this experimental investigation, the effects of thermal recuperation on the characteristics of asymmetric non-premixed vortex combustion are studied. The exhaust gases temperature, emissions and the combustor wall temperature are measured to evaluate thermal and emitter efficiencies. The results illustrate that in both combustors (with/without thermal recuperator), …

Applications Of Passive Solar Energy And Reclaimed Heat From Livestock Manure Decomposition, Naomi Elizabeth Schalle

Honors Theses

One energy intensive part of raising livestock in colder climates is keeping water warm and easily accessible to the animals in the winter. The objective of this project is to increase the sustainability of livestock farms by developing and implementing an energy conservation measure to decrease electric energy usage on the heating of water for livestock in the winter. One thing farmers have in excess is manure, an abundant and renewable resource for the farmers. This project will capitalize on that excess to encourage a creative use of resources often seen as waste, through implementing aspects of sustainability and conservation …

Spin-Controlled Wavefront Shaping With Plasmonic Chiral Geometric Metasurfaces, Yang Chen, Xiaodong Yang, Jie Gao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Metasurfaces, as a two-dimensional (2D) version of metamaterials, have drawn considerable attention for their revolutionary capability in manipulating the amplitude, phase, and polarization of light. As one of the most important types of metasurfaces, geometric metasurfaces provide a versatile platform for controlling optical phase distributions due to the geometric nature of the generated phase profile. However, it remains a great challenge to design geometric metasurfaces for realizing spin-switchable functionalities because the generated phase profile with the converted spin is reversed once the handedness of the incident beam is switched. Here, we propose and experimentally demonstrate chiral geometric metasurfaces based on …

Accelerated Freezing Due To Droplet Pinning On A Nanopillared Surface, Rachel Bohm, Mohammad Rejaul Haque, Chuang Qu, Edward C. Kinzel, Amy Rachel Betz

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The freezing process is significantly influenced by environmental factors and surface morphologies. At atmospheric pressure, a surface below the dew and freezing point temperature for a given relative humidity nucleates water droplets heterogeneously on the surface and then freezes. This paper examines the effect of nanostructured surfaces on the nucleation, growth, and subsequent freezing processes. Microsphere Photolithography (MPL) is used to pattern arrays of silica nanopillars. This technique uses a self-assembled lattice of microspheres to focus UV radiation to an array of photonic jets in photoresist. Silica is deposited using e-beam evaporation and lift-off. The samples were placed on a …

Me-Em Enewsbrief, December 2018, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical Engineering-Engineering Mechanics eNewsBrief

No abstract provided.

Opensim Versus Human Body Model: A Comparison Study For The Lower Limbs During Gait, Antoine Falisse, Sam Van Rossom, Johannes Gijsbers, Frans Steenbrink, Ben J. Van Basten, Ilse Jonkers, Antonie J. Van Den Bogert, Friedl De Groote

Mechanical Engineering Faculty Publications

Musculoskeletal modeling and simulations have become popular tools for analyzing human movements. However, end users are often not aware of underlying modeling and computational assumptions. This study investigates how these assumptions affect biomechanical gait analysis outcomes performed with Human Body Model and the OpenSim gait2392 model. The authors compared joint kinematics, kinetics, and muscle forces resulting from processing data from 7 healthy adults with both models. Although outcome variables had similar patterns, there were statistically significant differences in joint kinematics (maximal difference: 9.8 degrees {[}1.5 degrees] in sagittal plane hip rotation), kinetics (maximal difference: 0.36 {[}0.10] N.m/kg in sagittal plane …

Synergic Titanium Nitride Coating And Titanium Doping By Atomic Layer Deposition For Stable- And High-Performance Lifepo₄, Yan Gao, Jonghyun Park, Xinhua Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Atomic layer deposition (ALD) method has emerged as a promising technique to address the dissolution and poor conductivity of electrode materials of lithium ion batteries. In this work, surface modification of LiFePO₄ (LFP) was carried out by titanium nitride (TiN) ALD, during which a Ti doping into LFP occurred simultaneously. X-ray photoelectron spectroscopy (XPS) and electrochemical tests were performed to prove the Ti doping, and the composition of TiN layer on the surface of LFP particles was interpreted as a combination of TiN and titanium oxynitride (TiO_xN_y). Owing to the synergy of TiN coating and …

Evaluation Of Deformable Posts In The Zoi And Rigid Posts In Stiff Soil, Thomas Ammon

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Debris fences are commonly used by states, in conjunction with a concrete parapet, to protect railway tracks. Their use limits the intrusion of debris that could damage tracks or clutter rail lines. Due to a lack of previously crash-tested systems, the safety performance of such designs are largely unknown. The Iowa Department of Transportation (DOT) desired that researchers at the Midwest Roadside Safety Facility (MwRSF) design a crashworthy debris fence mounted on top of a concrete parapet to meet the Manual for Assessing Safety Hardware (MASH) TL-3 crash test conditions. Part 1 of this thesis details the literature review and …

Use Of The Wilshire Equations To Correlate And Extrapolate Creep Data Of Inconel 617 And Nimonic 105, Vito Cedro Iii, Christian Garcia, Mark Render

Mechanical Engineering Faculty Publications and Presentations

Advanced power plant alloys must endure high temperatures and pressures for durations at which creep data are often not available, necessitating the extrapolation of creep life. A recently developed creep life extrapolation method is the Wilshire equations, with which multiple approaches can be used to increase the goodness of fit of available experimental data and improve the confidence level of calculating long-term creep strength at times well beyond the available experimental data. In this article, the Wilshire equation is used to extrapolate the creep life of Inconel 617 and Nimonic 105 to 100,000 h. The use of (a) different methods …

A Conceptual Framework For Integration Development Of Gsflow Model: Concerns And Issues Identified And Addressed For Model Development Efficiency, Chao Chen, Sajjad Ahmad, Ajay Kalra

Civil and Environmental Engineering and Construction Faculty Research

In Coupled Groundwater and Surface-Water Flow (GSFLOW) model, the three-dimensional finite-difference groundwater model (MODFLOW) plays a critical role of groundwater flow simulation, together with which the Precipitation-Runoff Modeling System (PRMS) simulates the surface hydrologic processes. While the model development of each individual PRMS and MODFLOW model requires tremendous time and efforts, further integration development of these two models exerts additional concerns and issues due to different simulation realm, data communication, and computation algorithms. To address these concerns and issues in GSFLOW, the present paper proposes a conceptual framework from perspectives of: Model Conceptualization, Data Linkages and Transference, Model Calibration, and …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering News (2013-2023)

• Open Assistant Professor Position, Search 67645

Drop Generation Using Cross-Flow In Rigid Body Rotation, Haipeng Zhang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Inspired by crossflow membrane droplet generation and microfluidic droplet generation, I propose an easy method to generate monodisperse drops using cross-flow caused by rigid body rotation. In this approach, a dispersed phase (DP) liquid was injected through a stationary vertical needle into an immiscible continuous phase (CP) liquid which was in rigid body rotation. A DP drop growing at the end of the needle experienced fluid dynamic forces from the horizontal CP flow, and it was detached from the needle when it had grown to a certain size. This study investigated the relationship between the resultant size of drops and …

Cell For Flow Battery, Jonghyun Park, Mohammed Abdulkhabeer Al-Yasiri

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A reaction cell for a flow battery having flow channels positioned within a recess of a non-porous and non-brittle housing that is also a dielectric. Positioning the flow channels within the recess eliminates the need for end plates, gaskets, and insulators of conventional designs. A current collector and an electrode within the recess have areas approximately equal to the area of the recess such that they fit within the recess and maximize the contact area between them.

Weir Family Collection (Mss 651), Manuscripts & Folklife Archives

MSS Finding Aids

Finding aid for Manuscripts Collection 651. Letters and papers of the Weir family of Muhlenberg County, Kentucky, and related members of the Rumsey and Miller families. Well-to-do merchants and farmers, the Weirs were leading supporters of the Union during the Civil War, providing advocacy, financial support, and military service. Includes full-text scans of a letter from the brother of steamboat pioneer James Rumsey defending his legacy as an innovator; James Weir's journal; James Weir's will; the annotated recollections of Edward Weir, Sr.; and two letters from former Weir slaves recolonized in Liberia (Click on "Additional files" below).

Assessing The Limitations Of Effective Number Of Samples For Finding The Uncertainty Of The Mean Of Correlated Data, Barton L. Smith, Douglas R. Neal, Mark Feero, Geordie Richards

Mechanical and Aerospace Engineering Faculty Publications

The efficacy of recent and classical theories on the uncertainty of the mean of correlated data have been investigated. A variety of very large data sets make it possible to show that, under circumstances that are often too expensive to achieve, the integral time scale can be used to determine the effective number of independent samples, and therefore the uncertainty of the mean. To do so, the data set must be sufficiently large that it may be divided into many records, each of which is many integral time scales long. In this circumstance, all lags of the autocorrelation should be …

Cost Benefit Analysis Of Led Vs Florescent Lighting, Kurtis Clark, Phillip Humphrey

Student Research

Over the last few years, the state of Oklahoma has been looking at ways to reduce expenses to address concerns about a budget deficit. There have been efforts made to reduce expenses due to the use of energy. It has been said, when the lights are on, work is getting done. Running lights is therefore the cost of doing business. Our research examines the question, “is there a way to provide better lighting while operating at a lower cost.” This research examines the current lighting at Southwestern State University, primarily fluorescent lighting (FL), and a cost benefit analysis of switching …

Structural Transformations In Porous Glasses Under Mechanical Loading. Ii. Compression, Nikolai V. Priezjev, Maxim A. Makeev

Mechanical and Materials Engineering Faculty Publications

The role of porous structure and glass density in response to compressive deformation of amorphous materials is investigated via molecular dynamics simulations. The disordered, porous structures were prepared by quenching a high-temperature binary mixture below the glass transition into the phase coexistence region. With decreasing average glass density, the pore morphology in quiescent samples varies from a random distribution of compact voids to a porous network embedded in a continuous glass phase. We find that during compressive loading at constant volume, the porous structure is linearly transformed in the elastic regime and the elastic modulus follows a power-law increase as …

Frequency Response Of The Leap Motion Controller And Its Suitability For Measuring Tremor, Clay J. Kincaid, Austin C. Vaterlaus, Nathan R. Stanford, Steven Knight Charles

Faculty Publications

Although tremor is one of the most common movement disorders, it is evaluated using relatively coarse clinical scales. We propose to measure tremor in clinical settings using the Leap Motion Controller (LMC), which is a markerless motion capture sensor that has a low cost, zero set-up time, and dynamic accuracy of 1.2mm. However, the frequency response of the LMC has not been characterized, so its ability to track oscillations such as tremor is unknown. To characterize the frequency response of the LMC, we measured the position of a mannequin hand simultaneously with the LMC and a high-resolution encoder while the …