Mechanical Engineering Commons^™

Performance Of C2H4 Reductant In Activated-Carbon-Supported Mnox-Based Scr Catalyst At Low Temperatures, Guangli Liu, Dongtai Han, Jie Cheng, Yongshi Feng, Wenbin Quan, Li Yang, Kozo Saito

Mechanical Engineering Faculty Publications

Hydrocarbons as reductants show promising results for replacing NH₃ in SCR technology. Therefore, considerable interest exists for developing low-temperature (< 200 °C) and environmentally friendly HC-SCR catalysts. Hence, C₂H₄ was examined as a reductant using activated-carbon-supported MnOx-based catalyst in low-temperature SCR operation. Its sensitivity to Mn concentration and operating temperature was parametrically studied, the results of which showed that the catalyst activity followed the order of 130 °C > 150 °C > 180 °C with an optimized Mn concentration near 3.0 wt.%. However, rapid deactivation of catalytic activity also occurred when using C₂H₄ as the reductant. The mechanism of deactivation was explored and is …

Development And Thermodynamic Analysis Of An Integrated Mild/Partial Gasification Combined Cycle (Impgc) Under Green And Brown Field Conditions With And Without Carbon Capture, Henry A. Long Iii

University of New Orleans Theses and Dissertations

Coal is a very prominent energy source in the world, but it is environmentally unattractive due to its high sulfur and ash content as well as its alleged contribution towards climate change, but it is affordable, abundant, and has high energy content. Thus, utilizing coal in a cleaner and more efficient way has become necessary. One promising clean coal technology involves fully gasifying coal into synthesis gas, cleaning it, and feeding it into a high-efficiency combined cycle, such as an Integrated Gasification Combined Cycle (IGCC). Inspired by the recent success of warn gas cleanup (WGCU), mild and partial gasification are …

Towards Environmentally Sustainable And Cost-Effective Food Distribution In The U.S., Jasmina Burek

Graduate Theses and Dissertations

Distribution centers (DCs) and supermarkets have an important role in food sustainability, but no previous research has accounted for their environmental impact. The purpose of this research was to assess environmental sustainability of grocery, perishables, and general merchandise DCs; to estimate food storing and retailing impact; and to provide cost-effective strategies to reduce DCs’ environmental impacts. The importance and relevance of the research is threefold: improving sustainability of DCs, food storing, and food retailing. The main method used in this research was the life cycle assessment (LCA) method. An initial study calculated environmental impacts of the Wal-Mart Stores, Inc. DCs, …

Interfacial Tailoring Of Lithium-Ion Batteries By Atomic/Molecular Layer Deposition, Qian Sun

Graduate Theses and Dissertations

Lithium-ion batteries (LIBs) are promising energy storage devices, which play significant roles in addressing problems related to fossil fuels depletion and environmental pollution. Since the 1990s, LIBs have attracted great attention for many applications. Nowadays, LIBs are dominating portable electronics, having several advantages over their forerunners, such as high voltage (3.3~4.2 V) [1,2], low self-discharge (< 5~10 %/month) [3,4], wide operation temperature (-20~60 °C) [5,6], and fast charge/discharge rate [7,8]. However, LIBs deliver an energy density of 100-220 Wh/kg in practice to date, which is far from their theoretical ones, thus hindering their further applications in electric vehicles. Additionally, LIBs have been plagued by other problems, such as intolerance to overcharge/overdischarge, low heat resistance, lithium dendrites growth, large volume change of the silicon anode, large polarization and even safety problems.

Atomic layer deposition (ALD) and molecular layer deposition (MLD) are two important techniques, both proceeding in self-limiting gas-solid reactions and exhibiting excellent capabilities for ultra-thin films, conformal coatings, and controllable growth. They can be employed to address the problems of LIBs mentioned above by …

Local Peer-To-Peer Communication To Improve Demand Response In Residential Neighborhoods, Ryan Schwartz

Boise State University Theses and Dissertations

Increased electricity production from intermittent renewables presents a challenge to utilities. Since the grid has little ability to store energy, fluctuations in solar and wind generation require either an increase in generation from expensive sources or a reduction of demand. Demand Response (DR) programs focus on the latter and are designed to increase grid flexibility by allowing grid operators to modify when or how customers use electricity. For residential customers, this typically means shedding load during periods of high demand through a central controller temporarily shutting off air conditioning (AC) compressors. This type of DR can cause spikes in demand …

Intelligent Application Of Flexible Ac Transmission System Components In An Evolving Power Grid, Robert Wall

Graduate Theses and Dissertations

The world revolves around energy and the energy sector is continually transforming and evolving. The status quo has been set by governing agencies in the United States for completely reliable power. The demand for energy efficiency continually rises for multiple reasons. Technology has improved for all sectors of the power grid, including renewable energy sources, fault protection, and SMART grid technology. The addition of new energy sources has led to the decommissioning of inefficient energy sources. The implementation of new technologies and power load on a large scale, coupled with the removal of grid stabilizers has posed different challenges that …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

Cost Benefit Analysis Of Led Vs Florescent Lighting, Kurtis Clark, Phillip Humphrey

Student Research

Over the last few years, the state of Oklahoma has been looking at ways to reduce expenses to address concerns about a budget deficit. There have been efforts made to reduce expenses due to the use of energy. It has been said, when the lights are on, work is getting done. Running lights is therefore the cost of doing business. Our research examines the question, “is there a way to provide better lighting while operating at a lower cost.” This research examines the current lighting at Southwestern State University, primarily fluorescent lighting (FL), and a cost benefit analysis of switching …

Experimental Investigation Of The Heat Source Orientation On The Transient Flow And Thermal Behaviour Of Phase Change Material During Phase Transition, Steven Jevnikar

Electronic Thesis and Dissertation Repository

The present study reports the characterization of transient flow and transient thermal behavior of phase change material (PCM) during solid-liquid phase change (melting) through experimental investigation. Two specific aspects of the current work, both important in the field of latent heat thermal energy storage, are to investigate the influence of the flow behavior within liquid PCM on the melting and heat transfer processes, and the impact of heat source orientation on the underlying melting and heat transfer processes. A relationship between heat source orientation and the Nusselt number was discussed. The results show that the fluid velocity is critical for …

Semi-Annual Program Progress Performance Report For University Transportation Center Pppr#10, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

The Electric Vehicle Transportation Center (EVTC) supports the U.S. Department of Transportation's strategic goal of planning for near-term integration of alternative fuel vehicles as a means to build a sustainable transportation system. The project objectives are to evaluate technologies, standards, planning and policies to ensure seamless integration of electric vehicles (EVs) into a complex transportation network and electricity grid. The EVTC bridges the gap between deployment of electric vehicles and the traditional transportation system.

A Systematic Investigation Of Condensation Heat Transfer Using Asymmetric Micro-Scale Surfaces, Emily Brown

LSU Master's Theses

Asymmetric surfaces been shown to inducing unidirectional motion in the Leidenfrost regime; however, very minimal research has been conducted to investigate whether these surface can enhance condensation through the same means. The investigation of heat transfer of ratchets in condensation is a relatively untapped area of study, specifically ratchets with superhydrophobic properties. Anticipated difficulty lies in creating surfaces features or coatings that retain the ratchets and can adequately sustain optimal wetting state of Cassie-Baxter required to improve heat transfer performance during condensation. This study serves to investigate whether ratchets are a feasible surface feature to enhance condensation heat transfer. First, …

Modelling Hybrid Renewable Energy System For Philippine Merchant Marine Academy: A Feasibility Study, Nayan Guimpayan

World Maritime University Dissertations

No abstract provided.

2020 Low Sulphur Regulation: The Underlying Potential To Improve The ‘Energy Efficiency Design Index’ Of Ships, Nawin Ranjan Sharma

World Maritime University Dissertations

No abstract provided.

Ship-Port Interface: Analysis Of The Cost-Effectiveness Of Cold Ironing At Mombasa Port, Ronald Ssali

World Maritime University Dissertations

No abstract provided.

Novel Design And Synthesis Of Composite Nanomaterials For Lithium And Multivalent Ion Batteries, Wangwang Xu

LSU Doctoral Dissertations

Nowadays, the fast-increasing energy demand for efficient, sustainable and environmentally-friendly energy storage devices remains a significant and challenging issue. Lithium ion batteries (LIBs) have been widely used as commercial energy devices in portable electronics and also shown great promise in upcoming large-scale applications due to their advantages of environmental safety, efficiency in energy delivering and light weight. However, due to their limited capacity, energy densities and cycle ability, LIBs still need further improvement to expand their applications to a larger field, especially electric vehicle (EVs) and hybrid electric vehicles (HEVs), in which energy storage devices with large capacity and high …

Performance And Economic Analysis Of Hybrid Microhydro Systems, Ram Poudel

Doctoral Dissertations

Microhydro (MHP) systems usually employ unregulated turbines and an electronic load controller, a demand-side control device. Existing analytical models for such systems are lacking details, especially supply-side flow control, for performance simulation at hourly or sub-hourly scales. This work developed stochastic models for downscaling of streamflow and an empirical model of MHP systems. We integrated these models within the framework of Hybrid2 tool to simulate the long-term performance of a tri-hybrid system consisting of hydropower, solar PV and wind turbine. Based on an additive model of time series decomposition, we develop a Multiple Input Single Output (MISO) model in order …

Electrochemical Behaviors Of The Electrodes For Proton Conducting Intermediate Temperature Solid Oxide Fuel Cells (It-Sofc), Shichen Sun

FIU Electronic Theses and Dissertations

Proton conducting intermediate temperature (600oC-400oC) solid oxide fuel cells (IT-SOFC) have many potential advantages for clean and efficient power generation from readily available hydrocarbon fuels. However, it still has many unsolved problems, especially on the anode where the fuel got oxidized and the cathode where oxygen got reduced. In this study, for the anode, the effects of hydrogen sulfite (H2S) and carbon dioxide (CO2) as fuel contaminants were studied on the nickel (Ni) based cermet anode of proton conducting IT-SOFC using proton conducting electrolyte of BaZr0.1Ce0.7Y0.1Yb0.1O3 (BZCYYb). Both low-ppm level H2S and low-percentage level CO2 caused similar poisoning effects on …

Electrochemical Hydrogenation Of Acetone To Produce Isopropanol Using A Polymer Electrolyte Membrane Reactor, Chen Li, Ashanti M. Sallee, Xiaoyu Zhang, Sandeep Kumar

Civil & Environmental Engineering Faculty Publications

Electrochemical hydrogenation (ECH) of acetone is a relatively new method to produce isopropanol. It provides an alternative way of upgrading bio-fuels with less energy consumption and chemical waste as compared to conventional methods. In this paper, Polymer Electrolyte Membrane Fuel Cell (PEMFC) hardware was used as an electrochemical reactor to hydrogenate acetone to produce isopropanol and diisopropyl ether as a byproduct. High current efficiency (59.7%) and selectivity (>90%) were achieved, while ECH was carried out in mild conditions (65 degrees C and atmospheric pressure). Various operating parameters were evaluated to determine their effects on the yield of acetone and …

Policies That Impact The Acceleration Of Electric Vehicle Adoption, Florida Solar Energy Center

FSEC Energy Research Center®

To better understand the influence of policy initiatives that relate to electric vehicles (EVs) have on accelerated deployment, this project focused on a number of successful public and private initiatives and policies designed to encourage the adoption of EVs and related infrastructure. References to databases that keep pace with this rapidly evolving and transformative industry are included, and best practices for design of laws and incentives are provided.

Simulation Of The Oxygen Reduction Reaction (Orr) Inside The Cathode Catalyst Layer (Ccl) Of Proton Exchange Membrane Fuel Cells Using The Kinetic Monte Carlo Method, Baosheng Bai, Yi-Tung Chen

Mechanical Engineering Faculty Research

In this paper, a numerical model of the kinetic Monte Carlo (KMC) method has been developed to study the oxygen reduction reaction (ORR) that occurs inside the cathode catalyst layer (CCL). Firstly, a 3-D model of the CCL that consists of Pt and carbon spheres is built using the sphere packing method; secondly, an efficient procedure of the proton-oxygen reaction process is developed and simulated. In the proton-oxygen reaction process, all of the continuous movements of protons and oxygen are considered. The maximum reaction distance is determined to be 8 Å. The input pressures of protons and oxygen are represented …

The Correlation Between Energy Cost Share, Human, And Economic Development Using Time Series Data From Australasia, Europe, North America, And The Brics Nations, Ryan Roberts, Josephine Kaviti Musango, Alan Colin Brent, Matthew K. Heun

University Faculty Publications and Creative Works

This paper investigates how a change in a region's energy cost share (ECS), a ratio of a region's energy expenditure as a fraction of its gross domestic product (GDP), affects the region's social and economic development. Nations from four regions of the world, namely Australasia, Europe, North America, and the BRICS nations (Brazil, Russia, India, China, and South Africa) were chosen for this study. Using time series data from the period of 1978 to 2010, the annual ECS of each country was compared to the year-on-year GDP change, as well as the components of the human development index (HDI). High …

Design Of Wind Turbine Tower Height And Blade Length: An Optimization Approach, Ryan Wass

Mechanical Engineering Undergraduate Honors Theses

The wind industry is a fast growing market and is quickly becoming competitive with traditional non-renewable energy resources. As with any developing industry, research must continually be redefined as more complex understandings of design variables are learned. Optimization studies are common ways to quickly refine design variable selections. Historical wind turbine data shows that the tower hub height to rotor diameter ratio scales almost linearly. However there is no specific rule that dictates the optimum hub height for a given diameter. This study addresses this question by using an Excel based optimization program to determine the height to diameter ratio …

Waste Heat Recovery From A Vented Electric Clothes Dryer Utilizing A Finned-Tube Heat Exchanger, Abdul Raheem A. Shaik, Stephen L. Caskey, Eckhard A. Groll

The Summer Undergraduate Research Fellowship (SURF) Symposium

Conventional residential clothes dryers continuously vent moist, hot air during the drying process. The vented air leaves the home but still has useful temperature and humidity that could be recovered to offset other heating demands in the home. A study is carried out to quantify the amount of heat extracted from the waste heat stream of a conventional, vented clothes dryer. To extract the heat, a water cooled, fin-and-tube heat exchanger is located within the exhaust duct. A steady state thermodynamic dry coil and wet coil model was built in Engineering Equation Solver (EES). The model accounts for the heat …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

Untangling The Drivers Of Energy Reduction In The Uk Productive Sectors Efficiency Or Offshoring, Lukas Hardt, Anne Owen, Paul E. Brockway, Matthew K. Heun

University Faculty Publications and Creative Works

The UK has been one of the few countries that has successfully decoupled final energy consumption from economic growth over the past 15 years. This study investigates the drivers of final energy consumption in the UK productive sectors between 1997 and 2013 using a decomposition analysis that incorporates two novel features. Firstly, it investigates to what extent changes in thermodynamic efficiency have contributed to overall changes in sectoral energy intensities. Secondly, it analyses how much of the structural change in the UK economy is driven by the offshoring of energy-intensive production overseas. The results show that energy intensity reductions are …

2018-19 Tla Application - Thermal Fluid Sequence, M. A. Rafe Biswas

M. A. Rafe Biswas

No abstract provided.

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

Intermodel Comparison Between Switch 2.0 And Ge Maps: Evaluating A New Tool For Integrated Modeling Of Electric Vehicles And High-Renewable Power Systems, Florida Solar Energy Center, Matthias Fripp

FSEC Energy Research Center®

This report presents an inter-model comparison between the Switch and GE Energy Consulting, (GE) Multi Area Production Simulation (MAPS) power system models. This work was conducted as part of the project on the "Effect of Electric Vehicles on Power System Expansion and Operation" under a sub award to the Hawaii Natural Energy Institute, University of Hawaii at Manoa (UH), from the Electric Vehicle Transportation Center (EVTC) at the Florida Solar Energy Center, University of Central Florida. The EVTC is a University Transportation Center funded by the Research and Innovative Technology Administration of the US Department of Transportation. The EVTC is …

A Swing Generator Using Water Power Produced By The Wind, Ruka Ozaki

The International Student Science Fair 2018

I focus on various kinds of natural energy sources, especially wind. Wind power generation is the most-used method of electricity generation using wind power. Wind power generation has many merits; it achieves high efficiency of electric power generation, it can generate electricity even during the night, it doesn’t make any hazardous materials. However, there are not only merits but also demerits. It can cause bird strike, environment disruption from noise and low-frequency wave. And besides, we must comply building laws when we build wind power generators. Thus I built ‘a swing generator using water power produced by the wind power’, …

Comparison Of The 6th Edition Florida Building Energy Conservation Code With Iecc 2018 & Ashrae 90.1-2016, Florida Solar Energy Center, Jeffrey Sonne

FSEC Energy Research Center®

This study provides a comparison between the 6th Edition (2017) Florida Building Code, Energy Conservation and 2018 International Energy Conservation Code (IECC), based on approved 2015 to 2018 IECC changes included in the International Code document. And provides a stringency evaluation and cost-benefit analysis for those changes that impact energy use, to provide guidance for the upcoming 2017 to 2020 Florida Energy Code change cycle.