Mechanical Engineering Commons^™

3d Printing Of Biodegradable Scaffolds For Tissue Engineering Applications, Joe Morin, Michael Pickett, Amy Abraham, Tiera Martinelli

The Research and Scholarship Symposium (2013-2019)

With the recent improvements in three dimensional (3D) printing technologies, the potential for tissue engineering and regenerative medicine have significantly improved. One key idea in tissue engineering is to specifically design scaffolds to aid in the healing process by being incorporated into the body’s own tissue. The overall goal of this project is to investigate 3D printable scaffold design to access suitability for tissue replacement. This was accomplished by analyzing the effect of the material used to create the scaffolds, pore size, and pore shape on mechanical stiffness and cell culturability. Based on published literature, it was determined that, depending …

High-Throughput Tensile Testing Reveals Stochastic Properties In Additively Manufactured Steel, Bradley C. Salzbrenner

Mechanical Engineering ETDs

An adage within the Additive Manufacturing (AM) community is that “complexity is free”. Complicated geometric features that normally drive manufacturing cost and limit design options are not typically problematic in AM. While geometric complexity is usually viewed from the perspective of part design, this advantage of AM also opens up new options in rapid, efficient material property evaluation and qualification. This Thesis demonstrates how 100’s of miniature tensile bars can be produced and tested for comparable cost and in comparable time to a few conventional tensile bars. With this technique, it is possible to evaluate the stochastic nature of mechanical …

Underwater Ant House, Mark Duggan, Zachary Ellis, Zachary Soulier

Capstone Design Expo Posters

The project seeks to design and test and submersible enclosure capable of sustaining oxygen breathing life. A mesh covered in a superhydrophobic coating can both restrain water up to a maximum pressure and retain a direct interface between air and water. Oxygen can transfer over this boundary if there is a sufficient difference in concentrations between the water and air.

Multiple designs have been produced with the intent of testing and demonstrating these theories. 3D printing allowed for quick and customizable production of every component. Enclosures were made for testing the maximum allowable pressure and to fit an oxygen sensor. …

Low Velocity Impact And Rf Response Of 3d Printed Heterogeneous Structures, Sandeep Keerthi

Browse all Theses and Dissertations

Three-dimensional (3D) printing, a form of Additive manufacturing (AM), is currently being explored to design materials or structures with required Electro-Mechanical-Physical properties. Microstrip patch antennas with a tunable radio-frequency (RF) response are a great candidate for 3D printing process. Due to the nature of extrusion based layered fabrication; the processed parts are of three-layer construction having inherent heterogeneity that affects structural and functional response. The purpose of this study is to identify the relationship between the anisotropy in dielectric properties of AM fabricated acrylonitrile butadiene styrene (ABS) substrates in the RF domain and resonant frequencies of associated patch antennas and …

Anisotropy Evolution Due To Surface Treatment On 3d-Printed Fused Deposition Modeling (Fdm) Of Acrylonitrile Butadiene Styrene (Abs), Blake E. Lozinski

Honors Undergraduate Theses

Purpose: This paper will present insight to the methodology and results of the experimental characterization of Acrylonitrile Butadiene Styrene (ABS) using Fused Deposition Modeling (FDM). The work in this research explored the effects of print orientation, surface treatment, and ultraviolet (UV) light degradation with the utilization of Digital Image Correlation (DIC) on ABS tensile specimens.

Design/methodology: ABS specimens were printed at three build orientations (flat (0 degrees), 45 degrees, and up-right (90 degrees)). Each of these specimens were treated with three different surface treatments including a control (acrylic paint, Cyanoacrylate, and Diglycidyl Bisphenol A) followed by exposure to UV light …

Thermal Analysis Of 3d Printed 420 Stainless Steel, Adithya Pothuri

All Graduate Theses, Dissertations, and Other Capstone Projects

Additive manufacturing opens new possibilities in the manufacturing industry. 3D printing is a form of additive manufacturing. 3D printers will have a significant influence over the industrial market, with extremely positive effects in no time. The main aim of this research is to determine the effect of process parameters of Binder Jet manufactured 420 Stainless Steel (420SS) parts on thermal properties such as thermal conductivity. Different parameters, such as layer thickness, sintering time and sintering temperature were varied. A full factorial design of experiment matrix was made by varying these parameters using two levels. Testing showed that different parameters affected …

Additive Manufacturing Of Glass Using A Filament Fed Process, Junjie Luo

Doctoral Dissertations

"There are many scientific and engineering applications of glass including optics, communications, electronics, and hermetic seals, there has been minimal research towards the Additive Manufacturing (AM) of transparent glass parts. The special thermal and optical properties of glasses make them hard to be printed using conventional AM techniques. In this dissertation, two different AM techniques for glass AM were developed, Selective Laser Melting (SLM) and filament fed process.

Semi-transparent parts were printed with SLM process. However, the filament fed process was found to be more robust and promising for printing optically transparent glass parts. Therefore, this dissertation is focused on …

Design And Development Of A Foil Application Tool For A Foil Embedding Process In The Multi3d Manufacturing System, Betty Elizabeth Mckenzie

Open Access Theses & Dissertations

Additive manufacturing (AM) encompasses different technologies, including material extrusion 3D printing, a technology commonly referred to as fused deposition modeling (FDM), which is the focus of the work described in this manuscript. Additive manufacturing is a growing technology with many applications in numerous fields from the air force to medical offices. FDM is a process that uses thermoplastics, in this case polycarbonate (PC), where the PC is heated and selectively dispensed in a layer-by-layer process to create a 3D printed part. Currently, FDM systems have advantages over subtractive manufacturing or machining because cavities and other components (e.g., microchips, valves, and …

Design And Testing Of Scalable 3d-Printed Cellular Structures Optimized For Energy Absorption, Sagar Dilip Sangle

Browse all Theses and Dissertations

Sandwich panel structures are widely used due to their high compressive and flexural stiffness and strength-to-weight ratios, good vibration damping, and low through-thickness thermal conductivity. These structures consist of solid face sheets and low-density cellular core structures that are often based upon honeycomb topologies. Interest in additive manufacturing (AM), popularly known as 3D printing (3DP), has rapidly grown in past few years. The 3DP method is a layer-by-layer approach for the fabrication of 3D objects. Hence, it is very easy to fabricate complex structures with complex internal features that cannot be manufactured by any other fabrication processes. Due to the …

Low-Velocity Impact Behavior Of Sandwich Panels With 3d Printed Polymer Core Structures, Andrew Joseph Turner

Browse all Theses and Dissertations

Sandwich panel structures are widely used in aerospace, marine, and automotive applications because of their high flexural stiffness, strength-to-weight ratio, good vibration damping, and low through-thickness thermal conductivity. These structures consist of solid face sheets and low-density cellular core structures, which are often based upon honeycomb topologies. The recent progress of additive manufacturing (AM) (popularly known as 3D printing) processes has allowed lattice configurations to be designed with improved thermal-mechanical properties. The aim of this work is to design and print lattice truss structures (LTS) keeping in mind the flexible nature of AM. Several 3D printed core structures were created …

Resilience And Toughness Behavior Of 3d-Printed Polymer Lattice Structures: Testing And Modeling, Mohammed Al Rifaie

Browse all Theses and Dissertations

This research focuses on the energy absorption capability of additively manufactured or 3D printed polymer lattice structures of different configurations. The Body Centered Cubic (BCC) lattice structure is currently being investigated by researchers for energy absorption applications. For this thesis, the BCC structure is modified by adding vertical bars in different arrangements to create three additional configurations. Four designs or sets of the lattice structure are selected for comparison including BCC, BCC with vertical bars added to all nodes (BCCV), BCC with vertical bars added to alternate nodes (BCCA), and BCC with gradient arrangements of vertical bars (BCCG). Both experimental …