Mechanical Engineering Commons^™

Implications Of Electric Vehicles On Gasoline Tax Revenues, Florida Solar Energy Center, Kevin Schleith

FSEC Energy Research Center®

This report summarizes the results of research conducted to determine if current and near future EV sales will have an impact on gasoline (gas) tax revenues as part of the Federal Highway Trust Fund (HTF). Gasoline taxes account for $31.1 billion or about 87% of the HTF. The project results were accomplished through a review of existing industry and government reports that detail fuel tax revenues and through analysis of EV sales from 2010 to 2015.

Numerical-Analytical Assessment On Solar Chimney Power Plant, Nima Fathi, Seyed Sobhan Aleyasin, Peter Vorobieff

Nima Fathi

Muscle Synergies Improve Estimation Of Knee Contact Forces During Walking, Benjamin Fregly, Jonathan Walter, Allison Kinney, Scott Banks, Darryl D'Lima, Thor Besier, David Lloyd

Allison Kinney

This study investigates whether use of subject-specific muscle synergies can improve optimization predictions of muscle excitation patterns and knee contact forces during walking. Muscle synergies describe how a small number of neural commands generated by the nervous system can be linearly combined to produce the broad range of muscle electromyographic (EMG) signals measured experimentally. By quantifying the interdependence of individual EMG signals, muscle synergies provide dimensionality reduction for the neural control redundancy problem. Our hypothesis was that use of subjectspecific muscle synergies to limit muscle excitation patterns would improve prediction of muscle EMG patterns at the hip, knee, and ankle …

Muscle Synergy Constraints Improve Prediction Of Knee Contact Force During Gait, Benjamin Fregly, Jonathan Walter, Allison Kinney, Scott Banks, Darryl D'Lima, Thor Besier, David Lloyd

Allison Kinney

Knowledge of patient-specific muscle and joint contact forces during activities of daily living could improve the treatment of movement-related disorders (e.g., osteoarthritis, stroke, cerebral palsy, Parkinson’s disease). Unfortunately, it is currently impossible to measure these quantities directly under common clinical conditions, and calculation of these quantities using computer models is limited by the redundant nature of human neural control (i.e., more muscles than theoretically necessary to actuate the available degrees of freedom in the skeleton). Walking is a particularly important task to understand, since loss of mobility is associated with increased morbidity and decreased quality of life. Though numerous musculoskeletal …

Evaluation Of Different Optimal Control Problem Formulations For Solving The Muscle Redundancy Problem, Friedl De Groote, Allison Kinney, Anil Rao, Benjamin Fregly

Allison Kinney

This study evaluates several possible optimal control problem formulations for solving the muscle redundancy problem with the goal of identifying the most efficient and robust formulation. One novel formulation involves the introduction of additional controls that equal the time derivative of the states, resulting in very simple dynamic equations. The nonlinear equations describing muscle dynamics are then imposed as algebraic constraints in their implicit form, simplifying their evaluation. By comparing different problem formulations for computing muscle controls that can reproduce inverse dynamic joint torques during gait, we demonstrate the efficiency and robustness of the proposed novel formulation.

Material Properties And Microstructural Characterization Of Specimens, T.J. Silverman, Allison Kinney, B. South, W. Yong, J.H. Koo

Allison Kinney

The HiQ upgrade to the 3D Systems Vanguard selective laser sintering (SLS) machine incorporates a revised thermal calibration system and new software. This paper quantifies differences in mechanical and morphological properties of specimens built first using a Vanguard HS (high-speed) system and again using the same system with the HiQ upgrade applied. Standard specimens are built from DuraForm PA material and tested for tensile modulus, tensile strength, elongation at break, flexural modulus and Izod impact strength. The design of the specimen battery, the conduction of the tests and the significance of the results are discussed. The upgrade is found to …

Synergies Controls Improve Prediction Of Knee Contact Forces And Muscle Excitations During Gait, Benjamin Fregly, Jonathan Walter, Allison Kinney, Scott Banks, Darryl D'Lima, Thor Besier, David Lloyd

Allison Kinney

This study investigates whether use of muscle excitation controls constructed from subjectspecific muscle synergy information can improve optimization prediction of knee contact forces and muscle excitations during walking. Muscle synergies quantify how a large number of experimental muscle electromyographic (EMG) signals can be reconstructed by linearly mixing a much smaller number of neural commands generated by the nervous system. Our hypothesis was that controlling all muscle excitations with a small set of experimentally calculated neural commands would improve prediction of knee contact forces and leg muscle excitations compared to using independently controlled muscle excitations.

Comparison Of Material Properties And Microstructure Of Specimens Built Using The 3d Systems Vanguard Hs And Vanguard Hiq+Hs Sls Systems, T.J. Silverman, Allison Kinney, W. Yong, J.H. Koo

Allison Kinney

The HiQ upgrade to the 3D Systems Vanguard selective laser sintering (SLS) machine incorporates a revised thermal calibration system and new control software. The paper compares the tensile modulus, tensile strength, elongation at break, flexural modulus, Izod impact resistance and microstructure of two batteries of standard specimens built from recycled Duraform PA (Nylon 12). The first set is built on a Vanguard HS system and the second on the same system with the HiQ upgrade installed. The upgrade reduces user intervention, decreases total build time and improves surface finish. However, using the default processing parameters, tensile, flexure and impact properties …

U.S. Billion-Ton Update: Biomass Supply For A Bioenergy And Bioproducts Industry, Robert D. Perlack, Laurence M. Eaton, Anthony F. Turhollow Jr., Matt H. Langholtz, Craig C. Brandt, Mark E. Downing, Robin L. Graham, Lynn L. Wright, Jacob M. Kavkewitz, Anna M. Shamey, Richard G. Nelson, Bryce J. Stokes, William L. Rooney, David J. Muth Jr., J. Richard Hess, Jared M. Abodeely, Chad Hellwinckel, Danial De La Torre Ugarte, Daniel C. Yoder, James P. Lyon, Timothy G. Rials, Timothy A. Volk, Thomas S. Buchholz, Lawrence P. Abrahamson, Robert P. Anex, Thomas B. Voigt, William Berguson, Don E. Riemenschneider, Douglas Karlen, Jane M. F. Johnson, Robert B. Mitchell, Kenneth P. Vogel, Edward P. Richard Jr., John Tatarko, Larry E. Wagner, Kenneth E. Skog, Patricia K. Lebow, Dennis P. Dykstra, Marilyn A. Buford, Patrick D. Miles, D. Andrew Scott, James H. Perdue, Robert B. Rummer, Jamie Barbour, John A. Stanturf, David B. Mckeever, Ronald S. Zalesny Jr., Edmund A. Gee, P. Daniel Cassidy, David Lightle

Douglas L Karlen

The Report, Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply (generally referred to as the Billion-Ton Study or 2005 BTS), was an estimate of “potential” biomass within the contiguous United States based on numerous assumptions about current and future inventory and production capacity, availability, and technology. In the 2005 BTS, a strategic analysis was undertaken to determine if U.S. agriculture and forest resources have the capability to potentially produce at least one billion dry tons of biomass annually, in a sustainable manner—enough to displace approximately 30% of the country’s present petroleum …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Xingjian "Chris" Xue

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo₂O_5+δ (PBCO) cathode with a nanowire current collector was reduced …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Xingjian "Chris" Xue

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo2O5+δ (PBCO) cathode with a nanowire current collector was reduced by 44% at 650 …

Computational Simulation Of Mass Transport And Energy Transfer In The Microbial Fuel Cell System, Shiqi Ou

Doctoral Dissertations

This doctoral dissertation introduces the research in the computational modeling and simulation for the microbial fuel cell (MFC) system which is a bio-electrochemical system that drives a current by using bacteria and mimicking bacterial interactions found in nature. The numerical methods, research approaches and simulation comparison with the experiments in the microbial fuel cells are described; the analysis and evaluation for the model methods and results that I have achieved are presented in this dissertation.

The development of the renewable energy has been a hot topic, and scientists have been focusing on the microbial fuel cell, which is an environmentally-friendly …

High Temperature Hepa Filter Test Unit Upgrades, Alexander Krippner, Ian Corcorran, Michael Burlando

Mechanical Engineering

No abstract provided.

Thermal Hydraulic Turbine Dynamometer, Ryan Baskett, Alexander Campbell, Andrew Puntorno-Carlberg

Mechanical Engineering

No abstract provided.

Impurity Effects In All-Vanadium Redox Flow Batteries, Andrew William Burch

Masters Theses

In this dissertation, the effects of VOSO₄ [vanadyl sulfate] source and impurities on the beginning-of-life (BOL) performance of an all-vanadium redox flow battery (VRFB) are explored. Battery performance was monitored at 50% state of charge (SOC) using electrolyte with VOSO₄ purities of 99%, 99.9% and 99.99% by weight. At cell potentials of 1.23V, the least pure solution yielded the lowest current density of 280 mA/cm² [square centimeter] and the most pure solution yielded the highest, 560 mA/cm². The voltage efficiencies and charge-discharge capacities were shown to follow the same trends. Scanning electron microscopy (SEM) images …

Evaluation Of Two-Phase Evaporation Pressure Drop Correlations For Low Refrigerant Mass Flux., Anna Fenko

Electronic Theses and Dissertations

This study was conducted to evaluate three currently popular two-phase pressure drop models for extremely low velocity refrigerant flow through smooth circular evaporators in household refrigeration systems. Experimental data was taken at mass fluxes under 70 kg/m²s for two refrigerants, R134A and R600A, internal diameters of aluminum evaporators ranging from 0.186 to 0.317 inches, U-bend internal radii ranging from 0.342 to 0.750 inches in horizontal and vertical orientations of evaporators. The geometry of the samples closely resembled a commonly used serpentine shape with multiple U-bends experiencing both, up- and down-flow of the refrigerant. Two empirical models, Müller-Steinhagen & …

Optimization Of Titanium Liquid/Gas Diffusion Layers In Proton Exchange Membrane Electrolyzer Cells, Stuart Mccoy Steen

Masters Theses

Polymer electrolyte membrane electrolyzer cells (PEMECs), which are reverse PEM fuel cells (PEMFCs), are effective energy storage medium by producing hydrogen/oxygen from water using electricity from renewable energy sources. This is due in part because of its efficiency, high energy density, compact design, and large capacity. In a PEMEC, a liquid/gas diffusion layer (LGDL) is located between the catalyst layer and the current distributing flow field. The LGDL is expected to transport electrons, heat, and reactants/products to and from the catalyst layer with minimum voltage, current, thermal, interfacial, and fluidic losses. Carbon materials (carbon paper or carbon cloth), typically used …

Industrial Energy Consumption, Benchmarking, And Analysis In The United States, Daniel Maldonado

Mechanical Engineering Undergraduate Honors Theses

The purpose of this paper is to analyze the energy consumption of the industrial sector in the United States, and to identify the tools that can be used to minimize the consumption and improve the energy efficiency of all facilities in the country. The first part of the paper is a historical analysis of the industrial sector energy consumption, where the different energy sources are identified. The second part details different electronic tools that will provide facilities the ability of performing benchmarking, in order to understand their energy performance. Finally, the third part of this paper provides information about the …

A Look At Commercial Building Energy Use And Energy Efficiency Technologies From 1980 To Present, Marvin M. Arroyo

Mechanical Engineering Undergraduate Honors Theses

Energy consumption has increased considerably in the last fifty years as population rises. At the same time, design and efficiency of all equipment used in commercial buildings have changed as well. The purpose of this thesis is to explain how HVAC systems have changed and how they have affected energy consumption. Entities like the US Department of Energy (DOE) and the US Energy Information Administration (EIA) facilitate the data-gathering process by offering databases of energy information from actual monthly energy bills to promote public understanding of energy and its interaction with the economy and the environment. Moreover, in order to …

Simulation Of An Air Cooled Single-Effect Solar Absorption Cooling System With Evacuated Tube Collectors, Mohsen Jahandardoost

UNLV Theses, Dissertations, Professional Papers, and Capstones

Consistently increasing CO2 emission and ozone depletion from synthetic refrigerants are serious environmental issues challenging the scientific community. Absorption cooling systems give scope of utilizing low grade energy source for generating cooling effect. Solar energy is one of these low grade energy sources and with considering the fact that cooling demand increases with the intensity of solar radiation, solar refrigeration has been considered as a logical solution.

This thesis consists of two different simulation stages, in the first stage, a single effect lithium bromide absorption cooling system with constant cooling capacity is modeled and the effect of ambient and generator …

Cultural Change Through Bim: Driving Lean Transformation In Education, Avril Behan, Malachy Mathews, Kevin Furlong, Ciara Ahern, Una Beagon, Peter Brennan, Colin Conway, Lee Corcoran, Pierce Fahy, Alan Hore, Barry Mcauley, Trevor Woods

Conference papers

This paper presents a case study of how the adoption of BIM-based practices in the AECO industry is being reflected by cultural change in higher education in Ireland. The silo-mentality that has dominated the AECO sector for more than a century has, despite numerous reorganisations, been replicated in the structures of educational institutions, including in Dublin Institute of Technology since the inception of its founding colleges in the late 1800s. Most AECO programmes must include content that is external to the programme’s specific discipline. Through the School structures of the Institute, delivery of such content is known as "service teaching" …

Wind Power Capacity Value Metrics And Variability: A Study In New England, Frederick W. Letson

Doctoral Dissertations

Capacity value is the contribution of a power plant to the ability of the power system to meet high demand. As wind power penetration in New England, and worldwide, increases so does the importance of identifying the capacity contribution made by wind power plants. It is critical to accurately characterize the capacity value of these wind power plants and the variability of the capacity value over the long term. This is important in order to avoid the cost of keeping extra power plants operational while still being able to cover the demand for power reliably. This capacity value calculation is …

Semi-Annual Program Progress Performance Report For University Transportation Systems, Pppr#4, October 2015, Florida Solar Energy Center, David Block

FSEC Energy Research Center®

A summary of the major activities reported in the following pages is as follows. In the research area, the collection and analysis of data from the Nissan funded DC fast charger at FSEC (Project #3), the development of a student and faculty battery laboratory at Tuskegee University (Project #8), the opening of a new University of Hawaii battery test lab (Project #9), a computer model to optimize electrical costs for Tallahassee StarMetro buses (Project #14), and the installation and beginning of data collection from the FSEC wireless charging laboratory (Project #15). Detailed industry interactions for the period included Nissan, NovaCharge, …

الگو و دستورالعمل تهيه و تدوين پايان نامه کارشناسي ارشد, Dr Alireza Zolfaghari

Dr Alireza Zolfaghari

No abstract provided.

Umass Amherst Green Building Guidelines 2013, Ludmilla Pavlova-Gillham, Ted Mendoza, Ezra Small, Patricia O'Flaherty, Nariman Mostafavi, Mohamed Farzinmoghadam, Somayeh Tabatabaee Pozveh

Ludmilla D Pavlova

Facilities & Campus Services, Sustainable UMass and Campus Planning support sustainability and energy conservation initiatives by providing in-house resources to campus staff as well as designers and contractors working with the University. The UMass Amherst Green Building Guidelines provide a framework for approaching new construction and major renovation projects at UMass Amherst that are undergoing LEED certification by focusing the conversation on green building aspects that are most important to the campus. They are intended to be the beginning of a dynamic conversation between designers, environmental consultants and constructors, university stakeholders, and users of new high performance buildings.

Umass Amherst Energy Modeling Guidelines, Nariman Mostafavi, Ted Mendoza, Jeffrey G. Quackenbush, Sandy J. Beauregard, Jason J. Burbank, Mohamad Farzinmoghadam, Ludmilla Pavlova-Gillham, Kylie A. Landrey

Ludmilla D Pavlova

Facilities & Campus Services, Sustainable UMass and Campus Planning support sustainability and energy conservation initiatives by providing in-house resources to campus staff as well as designers and contractors working with the University. The Campus energy Modeling Guidelines were developed in 2015 as a resource on how to: i) generate energy models for campus buildings; ii) provide quality assurance review of current energy models; and iii) share UMass Amherst energy modeling input parameters with project design teams for them to establish a baseline building energy profile.

University Of Massachusetts Amherst 2012-2021 Capital Improvement Projects, Douglas Vigneau, Juanita Holler, John Mathews, Ludmilla Pavlova-Gillham, Ezra Small

Ludmilla D Pavlova

In 2013 the University of Massachusetts, on behalf of the University of Massachusetts Building Authority and Massachusetts Division of Capital Asset Management and Maintenance (DCAMM), submitted an Expanded Environmental Notification Form for the University's 2012 - 2021 Capital Improvement Plan to the Executive Office of Energy and Environmental Affairs (EOEEA) Massachusetts Environmental Policy Act Office (MEPA). Taken individually, the majority of the Projects, comprising of 13 building/space, 7 site/landscape, and 5 facility/ utility scale improvement projects, do not require MEPA review as most of the Project sites are confined to infill areas on campus that are currently or have been …

Heat-Driven Self-Cooling System Based On Thermoelectric Generation Effect, Robel Kiflemariam

FIU Electronic Theses and Dissertations

This research entails the first comprehensive and systematic study on a heat-driven, self-cooling application based on the thermoelectric generation effect. The system was studied using the first and second laws of thermodynamics to provide a solid and basic understanding of the physical principles governing the system. Multiphysics equations that relate heat transfer, fluid dynamics and thermoelectric generation are derived. The equations are developed with increasing complexity, from the basic Carnot heat engine to externally and internally irreversible engines. A computational algorithm to systematically use the fundamental equations has been presented and computer code is implemented based on the algorithm.

Experiments …

Why Doesn't 25 Years Of An Evolving Energy Code Make More Of A Difference?, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

This paper was presented at the 2015 Behavior, Energy and Climate Change Conference (BECC). New and more stringent building energy codes are implemented with the assumption and expectation that significant energy conservation will occur. While simulation and various analysis methodologies may be reasonably sound at estimating the energy impact, the actual impact is largely dependent upon new code enforcement and occupant behavior. This work is based upon the research question: Do homes built to a newer energy code deliver measurable energy savings compared to homes built to a much earlier energy code? This residential research study was focused on comparing …

Thermodynamic Analysis Of Closed Steady Or Cyclic Systems, Jim A. Mcgovern

Articles

Closed, steady or cyclic thermodynamic systems, which have temperature variations over their boundaries, can represent an extremely large range of plants, devices or natural objects, such as combined heating, cooling and power plants, computers and data centres, and planets. Energy transfer rates can occur across the boundary, which are characterized as heat or work. We focus on the finite time thermodynamics aspects, on energy-based performance parameters, on rational efficiency and on the environmental reference temperature. To do this, we examine the net work rate of a closed, steady or cyclic system bounded by thermal resistances linked to isothermal reservoirs in …