Mechanical Engineering Commons^™

Buckling, Postbuckling And Imperfection Sensitivity Analysis Of Different Type Of Cylindrical Shells By Hui's Postbuckling Method, Hailan Xu

University of New Orleans Theses and Dissertations

Hui and Chen (1986) were the first to show that the well-known Koiter’s General Theory of Elastic Stability of 1945 can be significantly improved by evaluating the postbuckling b coefficient at the actual applied load, rather than at the classical buckling load. Such improvement method was demonstrated to be (1) very simple to apply with no tedious algebra, (2) significant reduction in imperfection sensitivity and (3) although it is still asymptotically valid, there exists a significant extension of the range of validity involving larger imperfection amplitudes. Strictly speaking, Koiter’s theory of 1945 is valid only for vanishingly small imperfection amplitudes. …

Experimental Investigation Of Mist Film Cooling And Feasibility Study Of Mist Transport In Gas Turbines, Reda M. Ragab

University of New Orleans Theses and Dissertations

In the modern advanced gas turbines, the turbine inlet temperature may exceed 1500°C as a requirement to increase power output and thermal efficiency. Therefore, it is imperative that the blades and vanes are cooled so they can withstand these extreme temperatures. Film cooling is a cooling technique widely used in high-performance gas turbines. However, the film cooling effectiveness has almost reached plateau, resulting in a bottleneck for continuous improvement of gas turbines' efficiency.

In this study, an innovative cooling scheme, mist film cooling is investigated through experiments. A small amount of tiny water droplets with an average diameter about 10-15 …

A Wedge Impact Theory Used To Predict Bow Slamming Forces, Ashok Benjamin Basil Attumaly

University of New Orleans Theses and Dissertations

The pressures and impact forces acting on a hull while experiencing bow wave slamming is analyzed using Vorus' Impact Theory. The theory extends the hydrodynamic analysis of planing hulls from simple wedges to irregular shapes using a Boundary Element Method. A Fortran-based code developed by the Author is used to analyze hullforms. Linear strip theory is used to extend the analysis over a three dimensional hull. Post-processing of output data gives hull pressure distributions at different time steps and is visually presentable.

Impact pressure, Impact force, Planing, Wave slamming, Bow impact, Vorus' theory, Boundary Element Method, Linear strip theory

Experimental Investigation Of The Active Flow Control On A Two-Dimensional Wind Turbine Airfoil, Guannan Wang

Dissertations - ALL

Wind turbine blades experience unsteady aerodynamic loading under various off-design conditions. The fatigue loading reduces the operational time of the wind turbine hence leads to an increase in the Cost of Energy (CoE) of the wind power. In this study, active flow control with unsteady blowing actuators was applied to a two-dimensional wind turbine airfoil to alleviate the unsteady aerodynamic loading and improve the aerodynamic performance, particularly under large scale freestream disturbances. A low speed, open jet aeroacoustic wind tunnel was designed and constructed based on an existing anechoic chamber for this investigation. A theoretical analysis based on a Blade …

Experimental Study On The Effect Of Air Flow On Soap Bubble Formation, John M. Davidson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Soap bubbles are a common interfacial fluid dynamics phenomenon having applications such as buoyant hollow spherical fillers and flow visualization of large scale airflows. In contrast to the dynamics of liquid drops in gas and gas bubbles in liquid, the dynamics of soap bubbles has not been well documented, possibly because soap bubbles have gas-liquid-gas interfaces. Having the thin-liquid-film interface seems to alter the characteristics of the bubble/drop creation process. Thus, the main objective of this study is to experimentally examine how airflow develops and interacts with the soap liquid film as the film stretches and finally collapses to pinch-off. …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Liquid Phase Stability Under An Extreme Temperature Gradient, Zhi Liang, Kiran Sasikumar, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using Nonequilibrium Molecular Dynamics Simulations, We Subject Bulk Liquid to a Very High-Temperature Gradient and Observe a Stable Liquid Phase with a Local Temperature Well above the Boiling Point. Also, under This High-Temperature Gradient, the Vapor Phase Exhibits Condensation into a Liquid at a Temperature Higher Than the Saturation Temperature, Indicating that the Observed Liquid Stability is Not Caused by Nucleation Barrier Kinetics. We Show that, Assuming Local Thermal Equilibrium, the Phase Change Can Be Understood from the Thermodynamic Analysis. the Observed Elevation of the Boiling Point is Associated with the Interplay between the "Bulk" Driving Force for the Phase …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

The Stability And Control Of The Single Track Vehicles, Shyngys Karimov, Martin Corless

The Summer Undergraduate Research Fellowship (SURF) Symposium

Bicycles, motorcycles and scooters are all examples of the single track vehicles. The dynamics of the single track vehicle involve many degrees of freedom and various modes which govern its performance, making a complicated and interesting research topic. Motorcycle in motion can roll, yaw, and steer about the steering axis. It has three main modes which determine the motion and stability of it, they are weave, capsize, and wobble. The motorcycle performance is limited by the behavior of its modes, and if even one of the modes becomes unstable, the vehicle will roll over, and crash. The goal of this …

Solution To Certain Problems In The Failure Of Composite Structures, Jonathan Goodsell

Open Access Dissertations

The present work contains the solution of two problems in composite structures. In the first, an approximate elasticity solution for prediction of the displacement, stress and strain fields within the m-layer, symmetric and balanced angle-ply composite laminate of finite-width subjected anticlastic bending deformation is developed. The solution is shown to recover classical laminated plate theory predictions at interior regions of the laminate and thereby illustrates the boundary layer character of this interlaminar phenomenon. The results exhibit the anticipated response in congruence with the solutions for uniform axial extension and uniform temperature change, where divergence of the interlaminar shearing stress is …

Scalable Autonomous Operations Of Unmanned Assets, Sunghun Jung

Open Access Dissertations

Although there have been great theoretical advances in the region of Unmanned Aerial Vehicle (UAV) autonomy, applications of those theories into real world are still hesitated due to unexpected disturbances. Most of UAVs which are currently used are mainly, strictly speaking, Remotely Piloted Vehicles (RPA) since most works related with the flight control, sensor data analysis, and decision makings are done by human operators. To increase the degree of autonomy, many researches are focused on developing Unmanned Autonomous Aerial Vehicle (UAAV) which can takeoff, fly to the interested area by avoiding unexpected obstacles, perform various missions with decision makings, come …

Mapping Automotive Like Controls To A General Aviation Aircraft, Christopher G. Carvalho

Doctoral Dissertations and Master's Theses

The purpose of this thesis was to develop fly-by-wire control laws enabling a general aviation aircraft to be flown with automotive controls, i.e. a steering wheel and gas/brake pedals. There was a six speed shifter used to change the flight mode of the aircraft. This essentially allows the pilot to have control over different aspects of the flight profile such as climb/descend or cruise. A highway in the sky was used to aid in the navigation since it is not intuitive to people without flight experience how to navigate from the sky or when to climb and descend.

Many believe …

Tubular And Sector Heat Pipes With Interconnected Branches For Gas Turbine And/Or Compressor Cooling, Brian D. Reding Ii

FIU Electronic Theses and Dissertations

Designing turbines for either aerospace or power production is a daunting task for any heat transfer scientist or engineer. Turbine designers are continuously pursuing better ways to convert the stored chemical energy in the fuel into useful work with maximum efficiency. Based on thermodynamic principles, one way to improve thermal efficiency is to increase the turbine inlet pressure and temperature. Generally, the inlet temperature may exceed the capabilities of standard materials for safe and long-life operation of the turbine. Next generation propulsion systems, whether for new supersonic transport or for improving existing aviation transport, will require more aggressive cooling system …

Aerodynamic Simulation Of Vertical-Axis Wind Turbines, A. Korobenko, Ming-Chen Hsu, I. Akkerman, Y. Bazilevs

Ming-Chen Hsu

Full-scale, 3D, time-dependent aerodynamics modeling and simulation of a Darrieus-type vertical-axis wind turbine (VAWT) is presented. The simulations are performed using a moving-domain finite-element-based ALE-VMS technique augmented with a sliding-interface formulation to handle the rotor-stator interactions present. We simulate a single VAWT using a sequence of meshes with increased resolution to assess the computational requirements for this class of problems. The computational results are in good agreement with experimental data. We also perform a computation of two side-by-side counterrotating VAWTs to illustrate how the ALE-VMS technique may be used for the simulation of multiple turbines placed in arrays.

Qualitative Methods Used To Develop And Characterize The Circulation Control System On Cal Poly's Amelia, Eric N. Paciano

Master's Theses

The circulation control system onboard Cal Poly's Advanced Model for Extreme Lift and Improved Aeroacoustics was a critical component of a highly complex wind tunnel model produced in order to fulfill the requirements of a NASA Research Announcement awarded to David Marshall of the Aerospace Engineering Department. The model was based on a next generation, 150 passenger, regional, cruise efficient, short take-off and landing concept aircraft that achieved high lift through circulation control wings and over-the-wing mounted engines. The wind tunnel model was 10-ft in span, used turbine propulsion simulators, and had a functioning circulation control system driven from tunnel …

Fully Coupled Fluid And Electrodynamic Modeling Of Plasmas: A Two-Fluid Isomorphism And A Strong Conservative Flux-Coupled Finite Volume Framework, Richard Joel Thompson

Doctoral Dissertations

Ideal and resistive magnetohydrodynamics (MHD) have long served as the incumbent framework for modeling plasmas of engineering interest. However, new applications, such as hypersonic flight and propulsion, plasma propulsion, plasma instability in engineering devices, charge separation effects and electromagnetic wave interaction effects may demand a higher-fidelity physical model. For these cases, the two-fluid plasma model or its limiting case of a single bulk fluid, which results in a single-fluid coupled system of the Navier-Stokes and Maxwell equations, is necessary and permits a deeper physical study than the MHD framework. At present, major challenges are imposed on solving these physical models …

Essentially Analytical Theory Closure For Space Filtered Thermal-Incompressible Navier-Stokes Partial Differential Equation System On Bounded Domains, Mikhail Alexandrovich Sekachev

Doctoral Dissertations

Numerical simulation of turbulent flows is identified as one of the grand challenges in high-performance computing. The straight forward approach of solving the Navier-Stokes (NS) equations is termed Direct Numerical Simulation (DNS). In DNS the majority of computational effort is spent on resolving the smallest scales of turbulence, which makes this approach impractical for most industrial applications even on present-day supercomputers. A more feasible approach termed Large Eddy Simulation (LES) has evolved over the last five decades to facilitate turbulent flow predictions for reasonable Reynolds (Re) numbers and domain sizes. LES theory uses the concept of convolution with a spatial …

Plasmonics Resonance Enhanced Active Photothermal Effects In Aluminum Nanoenergetics For Propulsion Applications, Jacques Abboud

Doctoral Dissertations

In this dissertation, aluminum nanoparticles (Al NPs) are shown capable to on-demand enhance and control the local photothermal energy deposition, both spatially and temporally, via active photothermal effects initiated by the localized surface plasmon resonance (LSPR) phenomenon, and amplified by the Al exothermal oxidation reactions. Experiments in dry and wet environments along with computational modeling of the photothermal process are very desirable for gaining fundamental understanding, ignition optimization and parameter exploration.

Combined phenomena of motion and ignition of Al NPs are explored first in this study. Both resulting from exposing a pile of the nanoenergetics in hand to a single …

Multidimensional Compressible Framework For Modeling Biglobal Stability In Rocket Motors, Michel Henry Akiki

Doctoral Dissertations

Rocket motor stability analysis has historically been focused on two fundamental theories: the acoustic and the hydrodynamic. While the acoustic part examines the system at resonant states, the hydrodynamic component focuses on the fluid-wall interactions and the vortex shedding mechanisms which are responsible for exciting the system. Traditionally, the two concepts are studied independently and their results are then superposed for a more complete solution. In this study, we analyze the problem from a hydrodynamic standpoint and extend it to include compressibility. This is realized by reducing the linearized Navier-Stokes and energy equations to their biglobal form assuming a two-dimensional …

Mechanical Design Of Pird (Principal Investigator Rack Drawer) For Sofia, Hari Prasad Shetty Mr., Murali Krishna Kandlagunta Mrs., John Miles Mr., Zaheer Ali Mr.

STAR Program Research Presentations

SOFIA, the world’s largest airborne observatory with 2.5-meter diameter infrared telescope is equipped with 7 instruments: EXES, FIFI-LS, FLITECAM, FORCAST, GREAT, HAWC, and HIPO. Flying at altitudes between 39,000 and 45,000 feet, SOFIA avoids 99% of the atmospheric water vapor, records and analyzes the infrared radiation from the cosmos. SOFIA is able to observe the occultation of stars by solar system objects. By determining the size, compositions, and atmospheric structures of these objects, SOFIA can help answer the questions on creation and evolution of the universe, formation of the stars and planets, and nature of black hole at the center …

Synergies Controls Improve Prediction Of Knee Contact Forces And Muscle Excitations During Gait, Benjamin J. Fregly, Jonathan P. Walter, Allison Kinney, Scott A. Banks, Darryl D. D'Lima, Thor F. Besier, David G. Lloyd

Mechanical and Aerospace Engineering Faculty Publications

This study investigates whether use of muscle excitation controls constructed from subjectspecific muscle synergy information can improve optimization prediction of knee contact forces and muscle excitations during walking. Muscle synergies quantify how a large number of experimental muscle electromyographic (EMG) signals can be reconstructed by linearly mixing a much smaller number of neural commands generated by the nervous system. Our hypothesis was that controlling all muscle excitations with a small set of experimentally calculated neural commands would improve prediction of knee contact forces and leg muscle excitations compared to using independently controlled muscle excitations.

Linear Covariance Analysis For Gimbaled Pointing Systems, Randall S. Christensen

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Linear covariance analysis has been utilized in a wide variety of applications. Historically, the theory has made significant contributions to navigation system design and analysis. More recently, the theory has been extended to capture the combined effect of navigation errors and closed-loop control on the performance of the system. These advancements have made possible rapid analysis and comprehensive trade studies of complicated systems ranging from autonomous rendezvous to vehicle ascent trajectory analysis. Comprehensive trade studies are also needed in the area of gimbaled pointing systems where the information needs are different from previous applications. It is therefore the objective of …

Non-Destructive Testing (Ndt) By Laser Shearography And Fringe Projection, Xiaoran Chen, Morteza Khaleghi, Ivo Dobrev, Cosme Furlong

Morteza Khaleghi

Non-destructive testing (NDT) is critical to many precision industries because it can provide important information about the structural health of critical components and systems. In addition, NDT can also identify situations that could potentially lead to critical failures. Specifically, NDT by optical methods have become popular because of their non-contact and non-invasive nature. Shearography is a high-resolution optical NDT method for identification and characterization of structural defects in components and has gained wide acceptance over the last decade; however, as a drawback, shearography cannot locate the position of defects in 3D. To overcome this limitation, we are combining shearography with …

The Formulation And Computation Of The Nonlocal J-Integral In Bond-Based Peridynamics, Wenke Hu, Youn Doh Ha, Florin Bobaru, Stewart A. Silling

Florin Bobaru Ph.D.

This work presents a rigorous derivation for the formulation of the J-integral in bond-based peridynamics using the crack infinitesimal virtual extension approach. We give a detailed description of an algorithm for computing this nonlocal version of the J-integral.We present convergence studies (m-convergence and δ-convergence) for two different geometries: a single edge-notch configuration and a double edge-notch sample.We compare the results with results based on the classical J-integral and obtained from FEM calculations that employ special elements near the crack tip.We identify the size of the nonlocal region for which the peridynamic J-integral value is near the classical FEM solutions.We discuss …

The Meaning, Selection, And Use Of The Peridynamic Horizon And Its Relation To Crack Branching In Brittle Materials, Florin Bobaru, Wenke Hu

Florin Bobaru Ph.D.

This note discusses the peridynamic horizon (the nonlocal region around a material point), its role, and practical use in modeling. The objective is to eliminate some misunderstandings and misconceptions regarding the peridynamic horizon. An example of crack branching in a nominally brittle material (homalite) is addressed and we show that crack branching takes place without wave interaction. We explain under what conditions the crack propagation speed depends on the horizon size and the role of incident stress waves on this speed.

Crack Nucleation In A Peridynamic Solid, S. Silling, O. Weckner, E. Askari, Florin Bobaru

Florin Bobaru Ph.D.

A condition for the emergence of a discontinuity in an elastic peridynamic body is proposed, resulting in a material stability condition for crack nucleation. The condition is derived by determining whether a small discontinuity in displacement, superposed on a possibly large deformation, grows over time. Stability is shown to be determined by the sign of the eigenvalues of a tensor field that depends only on the linearized material properties. This condition for nucleation of a discontinuity in displacement can be interpreted in terms of the dynamic stability of plane waves with very short wavelength. A numerical example illustrates that cracks …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha Ph.D., Florin Bobaru Ph.D.

Florin Bobaru Ph.D.

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Microphone-Based Pressure Diagnostics For Boundary Layer Transition, Spencer Everett Lillywhite

Master's Theses

An experimental investigation of the use low-cost microphones for unsteady total pressure measurement to detect transition from laminar to turbulent boundary layer flow has been conducted. Two small electret condenser microphones, the Knowles FG-23629 and the FG-23742, were used to measure the pressure fluctuations and considered for possible integration with an autonomous boundary layer measurement system. Procedures to determine the microphones’ maximum sound pressure levels and frequency response using an acoustic source provided by a speaker and a reference microphone. These studies showed that both microphones possess a very flat frequency response and that the max SPL of the FG-23629 …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Rocket Fuel Pressurization, Sean Green, Joe Marcinkowski, Andrew Nahab

Mechanical Engineering

No abstract provided.