Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons

Open Access. Powered by Scholars. Published by Universities.®

Articles 1 - 5 of 5

Full-Text Articles in Mechanical Engineering

An On-Sun Parametric Study Of Solar Hydrogen Production Using Wo3 Photoanodes, Christopher K. Halford May 2009

An On-Sun Parametric Study Of Solar Hydrogen Production Using Wo3 Photoanodes, Christopher K. Halford

UNLV Theses, Dissertations, Professional Papers, and Capstones

The solar production of hydrogen using photoactive electrodes is a topic receiving much attention in recent years. The use of thin metal oxide films as photoanodes allows the water splitting reaction to occur at a much lower applied voltage than would be necessary with a straight electrolysis process. Researchers have reported up to 18% solar to hydrogen efficiencies over short periods. The University of Nevada Las Vegas in conjunction with the UK based firm Hydrogen Solar have developed a prototype of this type of cell using a WO3 photoanode. An on-sun test facility has been constructed by the UNLV Center …


Empirically Derived Formulas To Predict Indoor Maximum, Average, And Minimum Temperatures In Roofpond Buildings Using Minimum Climatic Information, Ibrahim Kivarkis Kako Jan 2009

Empirically Derived Formulas To Predict Indoor Maximum, Average, And Minimum Temperatures In Roofpond Buildings Using Minimum Climatic Information, Ibrahim Kivarkis Kako

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis introduces an empirically developed formula to predict the comfort conditions and thermal performance of a Skytherm(TM) Southwest Roofpond placed over a light-weight un-insulated structure built at the School of Architecture at the University of Nevada, Las Vegas.

The predictive formula introduced in this study may be used in different parts of the world (particularly developing nations where insulation and air-conditioning are rarely used) to predict the performance of a Skytherm(TM) Southwest Roofpond using minimal climate data.

The data collected in the experimental setup at the Natural Energies Advanced Technologies Laboratory included outside and inside temperatures of various surfaces …


Two-Tank Indirect Thermal Storage Designs For Solar Parabolic Trough Power Plants, Joseph E. Kopp Jan 2009

Two-Tank Indirect Thermal Storage Designs For Solar Parabolic Trough Power Plants, Joseph E. Kopp

UNLV Theses, Dissertations, Professional Papers, and Capstones

The performance of a solar thermal parabolic trough plant with thermal storage is dependent upon the arrangement of the heat exchangers that ultimately transfer energy from the sun into steam. The steam is utilized in a traditional Rankine cycle power plant. The most commercially accepted thermal storage design is an indirect two-tank molten salt storage system where molten salt interacts with the solar field heat transfer fluid (HTF) through a heat exchanger. The molten salt remains in a closed loop with the HTF and the HTF is the heat source for steam generation. An alternate indirect two tank molten salt …


Optimization Of Channel Geometry In A Proton Exchange Membrane (Pem) Fuel Cell, Jephanya Kasukurthi Jan 2009

Optimization Of Channel Geometry In A Proton Exchange Membrane (Pem) Fuel Cell, Jephanya Kasukurthi

UNLV Theses, Dissertations, Professional Papers, and Capstones

Bipolar plates are the important components of the PEM fuel cell. The flow distribution inside the bipolar plate should be uniform. Non-uniform flow distribution inside the bipolar leads to poor performance of the fuel cell and wastage of expensive catalyst. A single channel PEM fuel cell is taken and electrochemical analysis is carried out on it. The results are compared with the available published experimental data obtained by other research group, and they are found to be in good agreement. A baseline design of the bipolar plate is taken and numerical analysis is carried out. The results show that the …


Optimization Of Solid Oxide Fuel Cell Interconnect Design, Krishna C. Pulagam Jan 2009

Optimization Of Solid Oxide Fuel Cell Interconnect Design, Krishna C. Pulagam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Performance of solid oxide fuel cells (SOFC) is dependent of a set of complex physical and chemical processes occurring simultaneously. Interconnect for SOFC is important as it provides electrical connection between anode of one individual cell to the cathode of neighboring one. It also acts as a physical barrier to protect the air electrode material from the reducing environment of the fuel on the fuel electrode side, and it equally prevents the fuel electrode material from contacting with oxidizing atmosphere of the oxidant electrode side. A three-dimensional numerical model has been developed to evaluate the SOFC including the current collector, …