Mechanical Engineering Commons^™

Discrete Film Cooling In A Rocket With Curved Walls, Jonathan F. Mccall

Theses and Dissertations

This study quantified the effects of discrete wall-based film cooling in a rocket with curved walls. Simulations and experiments showed decreasing with wall radius of curvature, holding jet diameter constant, improves net heat flux reduction (NHFR) and adiabatic effectiveness (η) for 90˚ compound injected cylindrical jets, though η is reduced at the highest curvature. NHFR and η improved further with a high favorable stream-wise pressure gradient (K=2.1x10^-5) at all tested blowing ratios, but were affected little by a high density ratio (DR=1.76) using carbon dioxide as the coolant. Experiments were run at a Reynolds number of 31K and …

Design, Reconstruction And Evaluation Of A Dynamometer For Quarter Scale, Samuel Sanchez

BioResource and Agricultural Engineering

This project discusses the design, reconstruction, and evaluation of a dynamometer. A new test stand for the Quarter Scale team would improve the testing of the engines and the Continuously Variable Transmission (CVT). All the readings will be done electronically in order to provide the most accurate data collection. The dynamometer will be a closed hydraulic system for ease of use. This system will be able to test all of Quarter Scale engines. The data collected will be used to determine which engines are in the best condition, and which may need to be fixed. With the new design, the …

Two-Material Cylinder Stress Response Software, Katherine Gage, Matt Highstreet, Liz Del Cid

Mechanical Engineering

No abstract provided.

Module Cover Conductivity Enhancement, Niles Dhanens, James Fortner

Mechanical Engineering

A clam shell module cover for printed circuit boards (PCB) has been designed for use in Boeing’s AECM cabinet. The cover utilizes materials with high thermal conductivity and cools the PCB by conducting the heat to a cold plate interface. Materials were compared and aluminum 6061-T6, aluminum 3003, and annealed pyrolytic graphite (APG) were chosen. A prototype was built and tested using aluminum 6061-T6 which was able to dissipate 57.7% of the projected wattage. Issues may include unforeseen complications in assembly along with components performing at lower levels than specified by manufacturers. The APG prototype was unable to be tested …

Air Cooling For Aecm Module, Final Project Report, Kevin Whipp, Abraham Bruno Caulk

Mechanical Engineering

Advancements in electronics have created the need for improved cooling standards. The AECM standard, created to replace the antiquated ARINC 600 specification for aircraft, draws inspiration from a cooling specification known as VITA 48.2. The ARINC standard is in early stages of development and this project researches the feasibility of using air as a convective fluid instead of a liquid, the fluid used in the VITA specification.

A performance factor calculated from the ratio of the heat dissipated by convective heat exchanger plates over the power used to cause forced convective flow over said plates helps to quantify the effectiveness …

The Next Generation Router System Cooling Design, Garrett A. Glover

Master's Theses

Advancements in the networking and routing industry have created higher power electronic systems which dissipate large amounts of heat while cooling technology for these electronic systems has remained relatively unchanged. This report illustrates the development and testing of a hybrid liquid-air cooling system prototype implemented on Cisco’s 7609s router. Water was the working fluid through cold plates removing heat from line card components. The water was cooled by a compact liquid-air heat exchanger and circulated by two pumps. The testing results show that junction temperatures were maintained well below the 105°C limit for ambient conditions around 30°C at sea level. …

Absolute Nitrogen Atom Density Measurements By Two-Photon Laser-Induced Fluorescence Spectroscopy In Atmospheric Pressure Dielectric Barrier Discharges Of Pure Nitrogen, Et-Touhami Es-Sebbar, Christian Sarra-Bournet, Nicolas Naudé, Françoise Massines, Nicolas Gherardi

Dr. Et-touhami Es-sebbar

In this paper, two-photon absorption laser induced fluorescence spectroscopy is used to follow the nitrogen atom density in flowing dielectric barrier discharges fed with pure nitrogen and operating at atmospheric pressure. Two different dielectric barrier discharge regimes are investigated: the Townsend regime, which is homogeneous although operating at atmospheric pressure, and the more common filamentary regime. In both regimes, densities as high as 3x1014 /cm3 are detected. However, the N atoms kinetic formation depends on the discharge regime. The saturation level is reached more rapidly with a filamentary discharge. For a given discharge regime, the N atom density depends strongly …

Contributions To The Development Of The S.E.T.U.P. (Experimental And Theoretical Simulations Useful For Planetology) Project, E. Arzoumanian, C. Romanzin, M-C. Gazeau, Et. Es-Sebbar, A. Jolly, S. Perrier, Y. Benilan

Dr. Et-touhami Es-sebbar

No abstract provided.

Multiwavelength Studies For Titan's Atmospheric Composition Analysis, Y. Benilan, Et. Es-Sebbar, N. Fray, M-C. Gazeau, A. Jolly, M. Schwell, J. Guillemin

Dr. Et-touhami Es-sebbar

Titan's atmosphere mainly made of nitrogen and methane is rich in organic molecules. Hydrocarbons are formed from the photolytic dissociation of CH4 and nitriles are created by dissociation of N2 followed by reactions with hydrocarbons. In order to understand the physicochemical mechanisms responsible for the evolution of Titan's atmosphere, photochemical models are built. The latter need constrains for vertical profiles of organic compounds from the high thermosphere down to the low stratosphere as well as photodissociation rates. Those profiles over the entire atmosphere can be retrieved from Cassini observations, in particular by limb sounding, coupling infrared and ultraviolet spectroscopy. However, …

Vuv Photostability Of Prebiotic Species, M. Schwell, Y. Bénilan, M.-C. Gazeau, N. Fray, A. Jolly, Et. Es-Sebbar, N. Champion, S. Leach, H. W Jochims, H. Baumgärtel, E. Rühl

Dr. Et-touhami Es-sebbar

No abstract provided.

S.E.T.U.P. Experimental And Theoretical Simulations Useful For Planetology- Related Studies In The Frame Of A Program Of Titan’S Atmosphere Laboratory Simulations, M.-C. Gazeau, Et. Es-Sebbar, E. Arzoumanian, C. Romanzin, A. Jolly, S. Perrier, Y. Bénilan

Dr. Et-touhami Es-sebbar

No abstract provided.

Rayleigh Flow Of Two-Phase Nitrous Oxide As A Hybrid Rocket Nozzle Coolant, Lauren May Nelson

Master's Theses

The Mechanical Engineering Department at California Polytechnic State University in San Luis Obispo currently maintains a lab-scale hybrid rocket motor for which nitrous oxide is utilized as the oxidizer in the combustion system. Because of its availability, the same two-phase (gas and liquid) nitrous oxide that is used in the combustion system is also routed around the throat of the hybrid rocket’s converging-diverging nozzle as a coolant. While this coolant system has proven effective empirically in previous tests, the physics behind the flow of the two-phase mixture is largely unexplained. This thesis provides a method for predicting some of its …

Pattern Formation During The Evaporation Of A Colloidal Nanoliter Drop: A Numerical And Experimental Study, Rajneesh Bhardwaj, Xiaohua Fang, Daniel Attinger

Daniel Attinger

An efficient way to precisely pattern particles on solid surfaces is to dispense and evaporate colloidal drops, as for bioassays. The dried deposits often exhibit complex structures exemplified by the coffee ring pattern, where most particles have accumulated at the periphery of the deposit. In this work, the formation of deposits during the drying of nanoliter colloidal drops on a flat substrate is investigated numerically and experimentally. A finite-element numerical model is developed that solves the Navier–Stokes, heat and mass transport equations in a Lagrangian framework. The diffusion of vapor in the atmosphere is solved numerically, providing an exact boundary …

Characterization Of An N2 Flowing Microwave Post-Discharge By Oes Spectroscopy And Determination Of Absolute Ground-State Nitrogen Atom Densities By Talif, Et. Es-Sebbar, Y. Benilan, A. Jolly, M-C. Gazeau

Dr. Et-touhami Es-sebbar

A flowing microwave post-discharge source sustained at 2.45 GHz in pure nitrogen has been investigated by optical emission spectroscopy (OES) and two-photon absorption laser-induced fluorescence (TALIF) spectroscopy. Variations of the optical emission along the post-discharge (near, pink and late afterglow) have been studied and the gas temperature has been determined. TALIF spectroscopy has been used in the late afterglow to determine the absolute ground-state nitrogen atomic densities using krypton as a reference gas. Measurements show that the microwave flowing post-discharge is an efficient source of N (4S) atoms in late afterglow. In our experimental conditions, the maximum N (4S) density …

Design, Construction And Evaluation Of A Multi Layered Solar Distillation Prototype, Arlen A. Flanagan

BioResource and Agricultural Engineering

Water is arguably the most important resource to any individual; especially in areas of deserts and open oceans where drinkable water suppliers are scarce. The prototype Solar Desalination Unit allows normally undrinkable water to be distilled into a potable source with minimal inputs. The unit’s main power source is focused sunlight to thermally heat water inducing evaporation which is then condensed and collected. While solar desalination has been around for many years, lately more complex designs have been investigated in order to increase yields and efficiency. This paper focuses on the design, construction and testing of a Multi-Plate Solar Desalination …

Simulation Of An Oxidizer-Cooled Hybrid Rocket Throat: Methodology Validation For Design Of A Cooled Aerospike Nozzle, Peter Alexander Brennen

Master's Theses

A study was undertaken to create a finite element model of a cooled throat converging/diverging rocket nozzle to be used as a tool in designing a cooled aerospike nozzle. Using ABAQUS, a simplified 2D axisymmetric model was created featuring only the copper throat and stainless steel support ring, which were brazed together for the experimental test firings. This analysis was a sequentially coupled thermal/mechanical model. The steady state thermal data matched closely to experimental data. The subsequent mechanical model predicted a life of over 300 cycles using the Manson-Halford fatigue life criteria. A mesh convergence study was performed to establish …

Proceedings Of The Scientific Conference On Energy And It At Alvsjo Fair, Stockholm March 11-12, 2009 In Connection With The “Energitinget 2009, Dr. Erik Dahlquist, Dr. Jenny Palm

Dr. Erik Dahlquist

This book contains the proceedings from the Energy and IT conference at Alvsjo Energy conference "Energitinget" arranged by Swedish Energy Agency, with approximately 2500 visitors. The papers contain both technical and social science papers, relating to both energy efficiency in buildings and in industry.

An Experiment On Integrated Thermal Management Using Metallic Foam, Derek M. Geiger

Master's Theses

This report details an approach to using metal foam heat exchangers inside an integrated thermal management system on a variable cycle engine. The propulsion system of interest is a variable cycle engine with an auxiliary, variable flow rate fan. The feasibility of utilizing an open-celled metallic foam heat exchanger in the ducting between the constant and variable-fans on this variable cycle engine to cool the avionics was explored using an experimental approach. Two heat exchangers, 6.3 inch width by 6.3 inch length by 0.5 inch thickness, were constructed from 20 and 40 pores per inch (PPI) metal foam and tested. …

Experimental Evaluation And Modeling Of Engine Driven Heat Pump, Isaac Y. Mahderekal

UNLV Theses, Dissertations, Professional Papers, and Capstones

Recently, the Gas Engine-Driven Heat Pump (GHP) System has become an economic choice and more attractive climate control system than the conventional air conditioner due to its advantage in reducing fossil fuel consumption and environmental pollution. The GHP is a new type of heat pump in which the compressor (the core part) is driven by a gas engine. The GHP typically uses the work produced by the engine to drive a vapor-compression heat pump. At the same time, the waste heat rejected by the engine is used for heating purposes.

To improve the system performance of the GHP, a numerical …

12 - ارائة مدلي جديد به منظور ارزيابي احساس حرارتي افراد در هنگام خواب, Alireza Zolfaghari, Mehdi Maerefat

Dr Alireza Zolfaghari

No abstract provided.

11 - مدلسازي و تحليل ناپاياي پاسخ حرارتي بدن انسان در هنگام خواب, Alireza Zolfaghari, Mehdi Maerefat

Dr Alireza Zolfaghari

No abstract provided.

5 - امکان سنجي استفاده از سيستمهاي سرمايش تابشي سقفي با توجه به تنوع شرايط آب و هوايي و اقليمي در ايران, Alireza Zolfaghari, Mehdi Maerefat, Amir Omidvar

Dr Alireza Zolfaghari

No abstract provided.

Ceramic Matrix Composite Characterization Under A Combustion And Loading Environment, Andrew R. Nye

Theses and Dissertations

Lightweight materials that can withstand high temperatures and corrosive environments are constantly sought after in the aerospace industry, typically for Gas Turbine Engine (GTE) application. These materials need to retain their strength throughout the long service period they would see in the combustor and turbine components of a GTE. One material that is ideal for these types of applications is an oxide/oxide Ceramic Matrix Composite (CMC). The fatigue behavior of the oxide/oxide CMC Nextel^TM 720/Alumina (N720/A) was investigated in a unique high temperature environment. N720/A consisted of an 8-harness satin weave of Nextel^TM aluminum oxide/silicon oxide fibers bound …

Thermodynamically Coupled Heat And Mass Flows In A Reaction-Transport System With External Resistances, Yaşar Demirel

Yaşar Demirel Publications

Considerable work has been published on mathematically coupled nonlinear differential equations by neglecting thermodynamic coupling between heat and mass flows in reaction-transport systems. The thermodynamic coupling refers that a flow occurs without or against its primary thermodynamic driving force, which may be a gradient of temperature, or chemical potential, or reaction affinity. This study presents the modeling of thermodynamically coupled heat and mass flows of two components in a reaction-transport system with external heat and mass transfer resistances. The modeling equations are based on the linear nonequilibrium thermodynamics approach by assuming that the system is in the vicinity of global …

10 - استفاده از پوششهاي همسانه؛ راهکاري مناسب در جهت همگن سازي حرارتي محيط و کاهش مصرف انرژي در بخشهاي اداري و آموزشي, Alireza Zolfaghari, Mehdi Maerefat, Amir Omidvar

Dr Alireza Zolfaghari

No abstract provided.

9 - ارائه روشي جديد براي ارزيابي شرايط حرارتي بدن در شرايط پيچيدة محيطي, Alireza Zolfaghari, Mehdi Maerefat

Dr Alireza Zolfaghari

No abstract provided.

8 - روشي جديد براي مدلسازي پاسخ حرارتي بدن به شدت اغتشاشات جريان هواي وزشي و تخمين نارضايتي حرارتي ناشي از کوران, Amir Omidvar, Alireza Zolfaghari, Mehdi Maerefat

Dr Alireza Zolfaghari

No abstract provided.

Heat Transfer Correlations For Low Approach Evaporative Cooling Systems In Buildings, Ben Costelloe, Donal Finn

Articles

The experimental performance of an open industrial scale cooling tower, utilising small approach temperature differences (1–3 K), for rejection of heat at the low water temperatures (11–20 °C) typical of chilled ceilings and other sensible air–water heat dissipation systems in buildings, is examined. The study was carried out under temperate maritime climatic conditions (3–18 °C wet-bulb temperature range). Initially a theoretical analysis of the process at typical conditions for this climate was conducted, which indicated that a water to air (L/G) mass flow rate ratio of less than 1.0 was required for effective operation. Consequently for these low L/G ratios, …

Optimisation Of Heat Sink Design, Kevin Moore

Theses

In the field of electronics cooling and more specifically processor cooling, the ability to cool a micro-chip is becoming a major issue. Power dissipation in home and office computers has risen from 30W to over 120W in the past 10 years, forcing heat sink designers to search for new ideas in the design of their heat spreaders.

This thesis studies in detail the fundamental technical designs used for modern day processor cooling. Using Computational Fluid Dynamics (CFD), various different pin/fin shapes were analysed to determine which yielded maximum heat transfer and contact area with forced air flow. Elliptical and teardrop …

Singular Superposition/Boundary Element Method For Reconstruction Of Multi-Dimensional Heat Flux Distributions With Application To Film Cooling Holes, Mahmood Silieti, Eduardo Divo, Alain J. Kassab

Publications

A hybrid singularity superposition/boundary element-based inverse problem method for the reconstruction of multi-dimensional heat flux distributions is developed. Cauchy conditions are imposed at exposed surfaces that are readily reached for measurements while convective boundary conditions are unknown at surfaces that are not amenable to measurements such as the walls of the cooling holes. The purpose of the inverse analysis is to determine the heat flux distribution along cooling hole surfaces. This is accomplished in an iterative process by distributing a set of singularities (sinks) inside the physical boundaries of the cooling hole (usually along cooling hole centerline) with a given …