Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Mechanical Engineering
Experimental Verification Of Source Temperature Modulation Via A Thermal Switch In Thermal Energy Harvesting, Robin Mccarty, D. Monaghan, Kevin P. Hallinan, Brian Sanders
Experimental Verification Of Source Temperature Modulation Via A Thermal Switch In Thermal Energy Harvesting, Robin Mccarty, D. Monaghan, Kevin P. Hallinan, Brian Sanders
Mechanical and Aerospace Engineering Faculty Publications
This paper provides a description of research seeking to experimentally verify the effectiveness of a thermal switch used in series with TE devices for waste heat recovery for constant and variable source heat input and for variable source thermal capacitance (mass). Using an experimental set-up comprised serially of a fixed heat source, a variable thermal resistance air gap serving as a thermal switch, a thermoelectric device and a heat sink, the time-averaged power output to power input ratios improved up to 15% and 30% respectively for constant and variable heat input in certain design space conditions. The experimental results, as …
Comparison Of Material Properties And Microstructure Of Specimens Built Using The 3d Systems Vanguard Hs And Vanguard Hiq+Hs Sls Systems, T.J. Silverman, Allison Kinney, W. Yong, J.H. Koo
Comparison Of Material Properties And Microstructure Of Specimens Built Using The 3d Systems Vanguard Hs And Vanguard Hiq+Hs Sls Systems, T.J. Silverman, Allison Kinney, W. Yong, J.H. Koo
Mechanical and Aerospace Engineering Faculty Publications
The HiQ upgrade to the 3D Systems Vanguard selective laser sintering (SLS) machine incorporates a revised thermal calibration system and new control software. The paper compares the tensile modulus, tensile strength, elongation at break, flexural modulus, Izod impact resistance and microstructure of two batteries of standard specimens built from recycled Duraform PA (Nylon 12). The first set is built on a Vanguard HS system and the second on the same system with the HiQ upgrade installed. The upgrade reduces user intervention, decreases total build time and improves surface finish. However, using the default processing parameters, tensile, flexure and impact properties …
Development And Analysis Of A Software Package To Quantify In Vivo Polyethylene Wear After Total Hip Arthroplasty, Allison Kinney, Catherine G. Ambrose
Development And Analysis Of A Software Package To Quantify In Vivo Polyethylene Wear After Total Hip Arthroplasty, Allison Kinney, Catherine G. Ambrose
Mechanical and Aerospace Engineering Faculty Publications
Since the first total hip arthroplasty (THA) in 1938, THA evolved and developed into one of the major concentrations of orthopaedic research. The typical hip implant device used today incorporates a femoral and an acetabular component that serve to replicate the anatomical and mechanical functions of the natural hip joint. However, several problems exist that can effect the function of the implant device. Wear in the polyethylene liner of the acetabular component of the total hip replacement device is known as one of the major factors that affects the longevity of total hip replacement devices. Both manual and computer-aided techniques …
Fabrication Of Ankle-Foot Orthoses Using Selective Laser Sintering Technology, Allison Kinney, M. C. Faustini, Richard R. Neptune, R. H. Crawford, S. J. Stanhope
Fabrication Of Ankle-Foot Orthoses Using Selective Laser Sintering Technology, Allison Kinney, M. C. Faustini, Richard R. Neptune, R. H. Crawford, S. J. Stanhope
Mechanical and Aerospace Engineering Faculty Publications
Passive dynamic ankle-foot orthoses (AFOs) are often prescribed to improve gait performance for those with various neuromuscular disorders. Designs and materials used for AFOs range from simple polypropylene braces to advanced custom carbon fiber dynamic AFOs that passively store and release mechanical energy during gait. AFO designs vary in the shape and length of the foot component as well as the stiffness and length of the tibial component, depending on the desired functional outcomes. However, the current fabrication technology is not ideally suited for refined customization of AFO characteristics to optimize performance, or for rapid lowcost, high volume manufacturing and …
Industrial Solid-State Energy Harvesting: Mechanisms And Examples, Matthew Kocoloski, Carl Eger, Robin Mccarty, Kevin P. Hallinan, J. Kelly Kissock
Industrial Solid-State Energy Harvesting: Mechanisms And Examples, Matthew Kocoloski, Carl Eger, Robin Mccarty, Kevin P. Hallinan, J. Kelly Kissock
Mechanical and Aerospace Engineering Faculty Publications
This paper explores the potential for solid-state energy harvesting in industrial applications. In contrast to traditional heat recovery, the output of solid-state devices is electricity, which can be readily used in virtually any plant. The progress in harvesting waste heat via thermoelectric and thermionic generators is described. With second law efficiencies now approaching 50% and 80% respectively, we show that these technologies are on the cusp of practical use. Finally, we present an example of energy harvesting using thermionic devices in an industrial application. The example considers energy harvesting from a furnace at a glass manufacturing facility where exhaust gases …