Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Scanning electron microscopy (5)
- Bearings (machine parts) (3)
- Bronze (3)
- Cast iron (3)
- Failure (3)
-
- Failure (mechanical) (3)
- Lead (3)
- Leaded bronze bearing (3)
- Metallic wear debris (3)
- Microscopes (3)
- Microstructure (3)
- Rollers (machine components) (3)
- Wear failure (3)
- Wear of materials (3)
- Bonding (2)
- Casting (2)
- Extrusion (2)
- Interface (2)
- Metal matrix composites (2)
- Metallic matrix composites (2)
- Secondary phase (2)
- Stir casting (2)
- Wetting (2)
- Behavior (1)
- Beryllium bronze substrate (1)
- Coatings (1)
- Composites (1)
- Copper (1)
- Electrodeposition (1)
- Fretting wear (1)
Articles 1 - 6 of 6
Full-Text Articles in Mechanical Engineering
Microstructure And Interface Characteristics Of B4c, Sic And Al2o3 Reinforced Al Matrix Composites: A Comparative Study
A.S. Md Abdul Haseeb
Three aluminium metal matrix composites containing reinforcing particles of B4C, SiC and Al2O3 (0-20vol.%) were processed. The stir-casting manufacturing route followed by hot extrusion was utilized, being one of the cost-effective industrial methods. A clear interfacial reaction product/layer was found at Al-SiC interface for composites held for a relatively long processing time (>30 min). No reaction product was observed at Al-B4C and Al-Al2O3 interfaces at the resolution limit of the SEM used. On the other hand, two secondary phases (alumina and another phase containing aluminium, boron and carbon) were found in the aluminum matrix away from the interface in …
Microstructure And Interface Characteristics Of B4c, Sic And Al2o3 Reinforced Al Matrix Composites: A Comparative Study
A.S. Md Abdul Haseeb
Three aluminium metal matrix composites containing reinforcing particles of B4C, SiC and Al2O3 (0-20vol.%) were processed. The stir-casting manufacturing route followed by hot extrusion was utilized, being one of the cost-effective industrial methods. A clear interfacial reaction product/layer was found at Al-SiC interface for composites held for a relatively long processing time (>30 min). No reaction product was observed at Al-B4C and Al-Al2O3 interfaces at the resolution limit of the SEM used. On the other hand, two secondary phases (alumina and another phase containing aluminium, boron and carbon) were found in the aluminum matrix away from the interface in …
Wear Failure Of A Leaded Bronze Bearing: Correlation Between Plant Experience And Laboratory Wear Test Data
A.S. Md Abdul Haseeb
This paper describes an investigation on the failure of a large leaded bronze bearing that supports a nine-ton roller of a plastic calendering machine. At the end of the normal service life of a good bearing, which lasted for seven years, a new bearing was installed. However the new one failed catastrophically within a few days, generating a huge amount of metallic wear debris and causing pitting on the surface of the cast iron roller. Following the failure, samples were collected from both good and failed bearings. The samples were analyzed chemically and their microstructures examined. Both samples were subjected …
Wear Failure Of A Leaded Bronze Bearing: Correlation Between Plant Experience And Laboratory Wear Test Data
A.S. Md Abdul Haseeb
This paper describes an investigation on the failure of a large leaded bronze bearing that supports a nine-ton roller of a plastic calendering machine. At the end of the normal service life of a good bearing, which lasted for seven years, a new bearing was installed. However the new one failed catastrophically within a few days, generating a huge amount of metallic wear debris and causing pitting on the surface of the cast iron roller. Following the failure, samples were collected from both good and failed bearings. The samples were analyzed chemically and their microstructures examined. Both samples were subjected …
Wear Failure Of A Leaded Bronze Bearing: Correlation Between Plant Experience And Laboratory Wear Test Data
A.S. Md Abdul Haseeb
This paper describes an investigation on the failure of a large leaded bronze bearing that supports a nine-ton roller of a plastic calendering machine. At the end of the normal service life of a good bearing, which lasted for seven years, a new bearing was installed. However the new one failed catastrophically within a few days, generating a huge amount of metallic wear debris and causing pitting on the surface of the cast iron roller. Following the failure, samples were collected from both good and failed bearings. The samples were analyzed chemically and their microstructures examined. Both samples were subjected …
Fretting Wear Of Metallic Multilayer Films
Fretting Wear Of Metallic Multilayer Films
A.S. Md Abdul Haseeb
Fretting wear behaviour of electrodeposited Cu/Ni multilayer films with 10 and 5 nm thick sublayers has been investigated against a hardened steel ball as the counter body and compared with that of the constituents, Cu and Ni. The wear tests were carried out by using a ball-on-flat geometry at a translation frequency of 8 Hz and slip amplitude of 100 μm. Friction force was recorded on line during the tests. At the end of the tests, the wear scars were examined by laser surface profilometry, scanning electron microscopy and energy dispersive X-ray microanalysis. It has been observed that the frictional …