Mechanical Engineering Commons^™

Improvement Of Labyrinth Seal Leakage Rates Using Additive Manufacturing, Austin L. Gasbarra

Master's Theses

The growing popularity of additive manufacturing in commercial applications has al- lowed for new ideas and new ways of thinking when designing components. Further optimization at the component level is possible, though powder metallurgy is in its infancy. This study explores the possibility of using additive manufacturing to develop better labyrinth seals in turbomachinery. Labyrinth seals have a torturous fluid path with high losses, thus limiting the amount of fluid leakage. These types of seals can be non-rotating, allowing them to better take advantage of the additive manufacturing process due to the absence of rotating stresses. Labyrinth seal performance is …

Study On The Viability Of Preparing Plaster Molds For Rapid Prototyping Of Complex Ceramic Parts Using The Lost Pla Method, Shelton F. Fowler Iv

Honors College Theses

In the field of metal casting, cast parts often require an internal cavity to be made to meet design requirements. Frequently, these interior surfaces are not manufacturable through standard machining processes, and even when possible, they would most likely involve expensive and time-consuming operations. In order to avoid these machining costs, expendable ceramic or sand cores are manufactured and placed into the mold to allow the direct casting of complex internal geometries. This research seeks to use relatively inexpensive plastic 3D printing technology and the lost PLA casting process for the production of low-cost and rapidly producible ceramic cores. A …

Correlating In-Situ Monitoring Data With Internal Defects In Laser Powder Bed Fusion Additive Manufacturing, Andrew J. Harvey

Browse all Theses and Dissertations

The presence of defects within laser powder bed fusion (LPBF) parts can lead to reduced mechanical properties and life of components. Because of this, the ability to detect these defects within the parts is critical before the part is subject to its intended loading. Normally the parts are subjected to a quality analysis once they are completed however, this process is typically expensive and time consuming. A solution for these problems is to sense the creation of defects and pores in the parts in-situ, while the part is being fabricated. One proposed method of in-situ monitoring is visible spectroscopy to …

Multi-Wavelength Pyrometry For Emissivity Mapping And Accurate Surface Temperature Measurement In Powder Bed Fusion Systems, Md Moinuddin Shuvo

Open Access Theses & Dissertations

Accurate surface temperature measurement within powder bed fusion (PBF) systems during fabrication remains elusive for many reasons, despite the importance of knowing temperature for improving part quality, process control, repeatability and reproducibility, simulation capabilities, and more. Multi-wavelength (MW) pyrometry has been used previously to measure off-axis temperatures of a small region (~2.6mm in diameter) within an electron beam PBF (EBPBF) system. While this small region measurement makes it difficult to get a full field temperature map of the powder bed, it also allows for inline (on-axis) with laser temperature measurements for laser PBF (LPBF) systems. The MW pyrometry technique determines …

Development Of A Process For Thermal And Mechanical Modelling Of Screw-Driven Pellets Extrusion, Kaixiang Shi

Master’s Theses

The overall goal of the thesis project is to develop a process for thermal and mechanical modelling of the screw-driven pellets extrusion process, and applying the model results to design extruder temperature and flow rate controllers.

The proposed extruder is designed for metal 3D printing. The device demonstrates great potential in tackling some of the major issues faced by the metal additive manufacturing community. It eliminates the use of metal powder for workplace and workers safety. It is able to produce end-use parts with industrial grade mechanical and microstructural properties. It utilizes low cost metal-loaded polymer pellets as feedstock. However, …

Development Of Recepticals And Joints For Embedded Electronic Components Inserted During Print Via Hybrid Thermoplastic-Based Additive Manufacturing, Leonardo Isaac Gutierrez Sierra

Open Access Theses & Dissertations

The use of hybrid additive manufacturing (AM) systems is a novel approach in the fabrication of multi-functional parts. 3D printed electronics are an example of multi-functional parts fabricated using the Foundry Multi3D System, a hybrid AM system. Previous research has demonstrated the capabilities of the system by manufacturing RF antennas and satellite panels with embedded electronics, to name a few. However, research to identify design clearances and establish a manufacturing process plan had not been performed. The purpose of this manuscript is to determine the correct clearances for foreign components to be inserted unto a partially printed substrate. Besides this …

Mechanical Performance Of Ebm Ti-6al-2sn-4zr-2mo Influenced By The Effects Of Different Hot Isostatic Pressing Treatments, Miguel Lopez

Open Access Theses & Dissertations

Electron Beam Melting (EBM) is an additive manufacturing process that presents a lower level of internal defects in comparison to Selective Laser Melting (SLM). Pairing Hot Isostatic Pressing (HIP) with Additive Manufactured metal parts, sub-surface voids can be eliminated through high pressure and temperature. This significantly improves fatigue life, impact toughness, creep, rupture strength, and tensile ductility. In this investigation, Ti-6Al-2Sn-4Zr-2Mo samples manufactured in the Arcam's Q20 system will be tested as per ASTM E8 Standard Test Methods for Tension Testing of Metallic Materials. Different variants of Hot Isostatic Pressing (HIP) treatments were analyzed and compared. Tensile testing was performed …

Hydrokinetic Turbine Composite Blades And Sandwich Structures: Damage Evaluation And Numerical Simulation, Mokhtar Fal

Doctoral Dissertations

“Composite materials are gaining interest due to their high strength to weight ratio. This study deals with both experimental and numerical approaches to cover the aspects of the failure of composite materials in hydrokinetic turbine applications. In Part I, the location and magnitude of failure in the horizontal axis water turbine carbon fiber-reinforced polymer (CFRP) composite blades with different laminate stacking sequences were investigated. Two lay-up orientations were adopted for this work ([0⁰]₄ and [0⁰/90⁰]_2s). A finite element analysis model was generated to examine the stresses along the blade. Five angles were introduced to study the effect …

Performance Evaluation Of Alsi10mg Fabricated By A Selective Laser Melting Process, David Michael Murphy

Masters Theses

“Selective laser melting is becoming a widely used additive manufacturing technique that melts metal powder in a layer by layer process in order to build a desired part or geometry. Like many additive processes, selective laser melting allows for fabrication of parts with complex geometries. In order to fabricate a fully dense part there are a number of variables to take into account including: powder characteristics, laser parameters, and environmental parameters. Each of these variables can affect the microstructure and thus the mechanical performance of an additively manufactured part. In this work, the aluminum alloy AlSi10Mg was investigated. AlSi10Mg is …

Influence Of Input Energy On Mechanical Properties Of Laser Powder Bed Fused Aisi 304l Stainless Steel, Tan Pan

Masters Theses

“Powder Bed Fusion process with selective laser melting technique is popularly adopted in additive manufacturing area on account of its layer by layer manufacturing fashion capable of fabricating components with complex internal and external geometries and structures. However, the process-property map is unique and vital for different materials and AM configurations used for fabrication. The process parameter is identified as a significant factor that heavily influences the properties and performances of the printed materials.

Current work aimed to extend the existing knowledge on Laser Powder Bed Fusion fabricated AISI 304L by accessing the influence of varying energy input on the …

A Framework For A Successful Additive Repair System, Todd E. Sparks

Doctoral Dissertations

“The goal of this research is to generate a revolutionary improvement to the usability and usefulness of additive repair technology by integrating a set of tools into a seamless work flow. Insufficient automation in the current repair process is a huge hurdle in achieving cost-effective, reliable repairs. Many opportunities have been missed due to inconsistency, quality issues and lack of robustness and flexibility. The present work addresses deficiencies in preparatory steps such as 2D and 3D geometry processing, parameter estimation, and path planning as well as on-machine execution of the path plan. The bulk of the effort is focused on …

Additive Manufacturing Of Customized Lithium-Ion Batteries: Process Fundamentals And Applications, Xiaowei Yu

Doctoral Dissertations

“In the pasting decades, considerable efforts have been spent in developing the next-generation lithium-ion batteries (LIBs), from advanced active materials to new manufacturing methods. The development of additive manufacturing (AM) has brought new opportunities to LIBs. In this work, two AM methods are introduced for fabricating electrodes of LIBs. The first method is aerosol printing, which is a solvent-based wet additive method. Whereas the second method is a solvent-free, dry printing method. The commonly used materials for current collectors and active materials (including cathodes and anodes) of LIBs are aerosol printed and the electrochemical functionalities of the printed materials are …

Characterization Of Directed Energy Deposition Additively Manufactured Grcop-42 Alloy, Scott Landes

Electronic Theses and Dissertations

GRCop is an alloy family constructed of copper, chromium, and niobium and was developed by NASA for high heat flux applications. The first of its kind, GRCop-84, was specifically designed for the environments seen by channel cooled main combustion chamber liners. To further increase thermal conductivity while maintaining material strength characteristics, the percentage of alloying elements were cut in half and GRCop- 42 was developed. In recent years, NASA has successfully additively manufactured GRCop with comparable material characteristics to wrought GRCop using a Laser Powder Bed Fusion (L-PBF) process. Benefits of this process include fabrication of intricate cooling channels as …