Open Access. Powered by Scholars. Published by Universities.®
- Discipline
-
- Physical Sciences and Mathematics (3)
- Electro-Mechanical Systems (2)
- Materials Science and Engineering (2)
- Physics (2)
- Anatomy (1)
-
- Applied Mechanics (1)
- Biology and Biomimetic Materials (1)
- Biomaterials (1)
- Biomedical Devices and Instrumentation (1)
- Biomedical Engineering and Bioengineering (1)
- Cardiovascular System (1)
- Chemical Engineering (1)
- Computer-Aided Engineering and Design (1)
- Controls and Control Theory (1)
- Dynamics and Dynamical Systems (1)
- Electrical and Computer Engineering (1)
- Energy Systems (1)
- Engineering Physics (1)
- Engineering Science and Materials (1)
- Environmental Sciences (1)
- Fluid Dynamics (1)
- Heat Transfer, Combustion (1)
- Manufacturing (1)
- Medicine and Health Sciences (1)
- Nanoscience and Nanotechnology (1)
Articles 1 - 6 of 6
Full-Text Articles in Mechanical Engineering
Designing Cryogenic Strain Device For 2d Materials, Jake Carter
Designing Cryogenic Strain Device For 2d Materials, Jake Carter
Mechanical Engineering Undergraduate Honors Theses
The Churchill lab working within the Physics Department at the University of Arkansas is working to create important quantum states including weak topological insulators (TIs) through the use of symmetry engineering and topological electronic states in two-dimensional (2D) crystals of WHM materials. Experimental results of these topological states have been obstructed due to the difficulty to perform controlled in situ strain. This project strives to create a mount to utilize a piezoelectric nanopositioner within cryostats achieving an in situ strain that creates the quantum states the lab is looking to observe. This report also examines the necessary equations to determine …
Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins
Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins
Mechanical Engineering Undergraduate Honors Theses
According to the CDC, atrial fibrillation is responsible for more than 454,000 hospitalizations and approximately 158,000 deaths per year. A common treatment for atrial fibrillation is catheter ablation, a process in which a long flexible tube is guided through the femoral artery and to the source of arrhythmia in the heart, where it measures the electrical potential at various locations and converts problematic heart tissue to scar tissue via ablation. This paper details the design and control of a low-cost ($400) peristaltic pump system using repetitive control to replicate blood pressure in the left atrium in a conductive silicone model …
Thermal Testing And Characterization Of Nanoparticles Synthesized For Biological Treatment, Tonie Butler
Thermal Testing And Characterization Of Nanoparticles Synthesized For Biological Treatment, Tonie Butler
Mechanical Engineering Undergraduate Honors Theses
The overall goal of this research project is to synthesize iron core, silica capped nanoparticles that, when they are exposed to a particular magnetic field, will react by increasing in temperature and emitting substantial thermal output. They will be injected into the human body for biological benefit by targeted thermal radiation. Once in the human body, ideally, they will be able to target a specific area, and then a magnetic field will be applied to induce thermal output through the process of hyperthermia. As the nanoparticles emit heat, they will mimic the natural bodily behavior seen by way of hyperthermia, …
Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend
Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend
Chemical Engineering Undergraduate Honors Theses
Plastic waste generation is increasing at an unsustainable rate while recycling solutions remain stagnant. As a chemical means of recycling, mixed plastic waste pyrolysis can generate synthetic oil appropriate for use as fuel in power generation from plastic waste that otherwise accumulates in landfills. With the scaling of a commercial plastic pyrolysis process in Northwest Arkansas (NWA) modeled after an operational sawdust pyrolysis unit in Huntsville, Arkansas, economic analysis resulted in 26.3% internal rate of return. Therefore, construction of a commercial mixed plastic-to-fuel pyrolysis plant is economically justified and should be pursued. To effectively implement the proposed design, NWA must …
Silicone Tadpole: Research Into Soft Bodies, Danielle Fernandez
Silicone Tadpole: Research Into Soft Bodies, Danielle Fernandez
Mechanical Engineering Undergraduate Honors Theses
In this thesis, research is conducted in the area of soft robotics by building a soft tadpole that can deform with a specific air pressure. The goal is to mimic the motion of an organic tadpole in respect to its S-shaped tail movement. The angle of deformation, derived from material mechanic theories, ranges from 45 to 80 degrees for this type of movement. The design includes a head compartment which acts as a tank to transfer nitrogen pressure and a tail section that receives the said pressure and bends as a result. The tail section was designed with two rows …
Photochemical Etching Of Nitrided Stainless Steel Piston Rings, Steven Sonntag
Photochemical Etching Of Nitrided Stainless Steel Piston Rings, Steven Sonntag
Mechanical Engineering Undergraduate Honors Theses
Piston rings are designed to provide a seal between the piston and the cylinder wall of internal combustion engines, keeping oil from the crankcase from getting into the combustion chamber. This means piston rings are the main point of contact between the piston and the cylinder wall, which causes the piston to experience high amounts of friction and wear. By texturing the surfaces of the cylinder wall and/or the piston ring, the amount of contact area can be reduced, allowing for less friction, slower wear, and better gas mileage. In this thesis experiments, photochemical etching processes were developed to etch …