Mechanical Engineering Commons^™

Cfd Simulation Investigating The Effects Of Groove Geometry On Heat Transfer For Internally Grooved Tubes, Richard Zaven Saroukhanoff

UNLV Theses, Dissertations, Professional Papers, and Capstones

This numerical study investigates the thermal performance of internally grooved tubes used in heat exchangers. In order to enhance the performance of heat exchangers, turbulence promoters are inserted along the streamwise flow. The use of inserts, grooves, and augmentations along the axial length of the tube creates disturbances that improve the overall heat transfer due to enhanced fluid mixing and greater surface contact boundary walls. However, the implementation of tube wall augmentations creates an increase in pressure drop across the tube which must be compensated for with additional pumping power for the working fluid. Therefore, in order to analyze the …

Polymeric Impulsive Actuation Mechanisms: Development, Characterization, And Modeling, Yongjin Kim

Doctoral Dissertations

Recent advances in the field of biomedical and life-sciences are increasingly demanding more life-like actuation with higher degrees of freedom in motion at small scales. Many researchers have developed various solutions to satisfy these emerging requirements. In many cases, new solutions are made possible with the development of novel polymeric actuators. Advances in polymeric actuation not only addressed problems concerning low degree of freedom in motion, large system size, and bio-incompatibility associated with conventional actuators, but also led to the discovery of novel applications, which were previously unattainable with conventional engineered systems. This dissertation focuses on developing novel actuation mechanisms …

Understanding The Interplay Between Fluid Mechanics And Particle Size Distributions For Filtration Of Flocculated Mixtures, Brooke Remler

Electronic Thesis and Dissertation Repository

The breakdown of nutrients in biological processes in wastewater treatment require a sub- stantial amount of energy, contributing to greater greenhouse gas (GHG) emissions. Floc- culation can be used to reduce the loading on a biological process by increasing removals during primary treatment in devices such as a rotating belt filter (RBF). The relationship between shear conditions, defined by velocity gradients (G-values) and floc size is crucial. Understanding G-value magnitudes and distributions within an RBF, corresponding trans- port network, and the effects on floc size degradation are needed to maximize removals. G-values were calculated using a newly developed approach, improving …

Investigation Of The Electrode Polarization Effect For Biosensor Applications, Anil Koklu

Mechanical Engineering Research Theses and Dissertations

My research focuses on electrokinetic transport. Particularly, in this dissertation, we focus on fabrication and testing of micro electrodes with nanostructured surfaces to minimize the electrode polarization (EP) effects for biosensor applications. In the first study, electrochemical deposition of gold nanoparticles on to planar gold electrodes was used to generate rough surfaces. Dendritic nanostructures that reduced EP up to two orders of magnitude was obtained by optimizing the deposition conditions. These structures also enhanced dielectrophoresis (DEP) response of our bio-chips, making them usable in physiological buffers. In further studies we discovered a universal scaling of EP in the frequency domain, …

Fluid Flow Analysis Of Diluted Evaporating American Whiskey Droplets., Martin J. Brown Vi

Electronic Theses and Dissertations

The recent discovery of the unique structures, whiskey webs, formed when the evaporation of diluted American whiskey, has raised many questions as to the nature of the structures. Their formation process follows as such: (1) dilution of the whiskey to form nanoaggregates, (2) formation of a monolayer at the air-liquid interface, (3) chaotic ethanol evaporation caused monolayer collapse (via dynamic pressure), (4) bulk fluid evaporation caused monolayer collapse (via reduction of surface area), where the web-like structures reside on the surface, and finally, (5) web-like structures deposit on the substrate. The webs imaged via SEM had a striking resemblance to …

Maximizing And Modeling Malonyl-Coa Production In Escherichia Coli, Tatiana Thompson Silveira Mello

LSU Master's Theses

In E. coli, fatty acid synthesis is catalyzed by the enzyme acetyl-CoA carboxylase (ACC), which converts acetyl-CoA into malonyl-CoA. Malonyl-CoA is a major building block for numerous of bioproducts. Multiple parameters regulate the homeostatic cellular concentration of malonyl-CoA, keeping it at a very low level. Understanding how these parameters affect the bacterial production of malonyl-CoA is fundamental to maximizing it and its bioproducts. To this end, competing pathways consuming malonyl-CoA can be eliminated, and optimal nutritional and environmental conditions can be provided to the fermentation broth. Most previous studies utilized genetic modifications, expensive consumables, and high-cost quantification methods, making …

A Numerical Simulation Optimizing Droplet Motion Driven By Electrowetting, Jake M. Lesinski

Master's Theses

A numerical simulation of electrowetting on a dielectric was performed in COMSOL to grant insight on various parameters that play a critical role in system performance. The specific system being simulated was the Open Drop experiment and the parameters being investigated were the applied voltage, contact angle at the advancing triple point, and droplet overlap onto neighboring actuated electrodes. These parameters were investigated with respect to their effect on droplet locomotion performance. This performance was quantified by the droplets velocity and the dielectrophortic (DEP) force’s magnitude; the DEP force was calculated from integration of the Maxwell Stress Tensor, however, the …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Examination Of Flow Dynamics And Passive Cooling In An Ultra Compact Combustor, Tylor C. Rathsack

Theses and Dissertations

The Ultra Compact Combustor (UCC) promises to greatly reduce the size of a gas turbine engine’s combustor by altering the manner in which fuel is burnt. Differing from the common axial flow combustor, the UCC utilizes a rotating flow, coaxial to the engine’s primary axis, in an outboard circumferential cavity as the primary combustion zone. The present study investigates two key UCC facets required to further this combustor design. The first area of investigation is cooling of the Hybrid Guide Vane (HGV). This UCC specific hardware acts as a combustor center body that alters the exit flow angle and acts …

Capillary Forces In Partially Saturated Thin Fibrous Media, Ali Moghadam

Theses and Dissertations

Capillarity is often exploited in self-cleaning, drag reducing and fluid absorption/storage (sanitary products) purposes just to name a few. Formulating the underlying physics of capillarity helps future design and development of optimized structures. This work reports on developing computational models to quantify the capillary pressure and capillary forces on the fibrous surfaces. To this end, the current study utilizes a novel mass-spring-damper approach to incorporate the mechanical properties of the fibers in generating virtual fibrous structures that can best represent fibrous membranes. Such virtual fibrous structures are then subjected to a pressure estimation model, developed for the first time in …

Void Fraction Measurements In Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensor And Pressure Transducers- Effect Of Sparger, Afolabi Gabriel Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

Modeling Electrospun Fibrous Materials, Sina Hassanpouryousefi

Theses and Dissertations

Electrospinning has been the focus of countless studies for the past decades for applications, including but not limited to, filtration, tissue engineering, and catalysis. Electrospinning is a one-step process for producing nano- and/or micro-fibrous materials with diameters ranging typically from 50 to 5000 nm. The simulation algorithm presented here is based on a novel mass-spring-damper (MSD) approach devised to incorporate the mechanical properties of the fibers in predicting the formation and morphology of the electrospun fibers as they travel from the needle toward the collector, and as they deposit on the substrate. This work is the first to develop a …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Plenum-To-Plenum Heat Transfer Characteristics Under Natural Circulation In A Scaled-Down Prismatic Modular Reactor, Salman Mohammed Alshehri

Doctoral Dissertations

“Gas-cooled reactor (GCR) is being developed under the Next Generation Nuclear Plant Program (NGNP) in nuclear engineering studies. As the world searches for an energy source with high energy density, clean, abundant, and storable nature to avoid global warming issues, GCR seems to be a promising solution, particularly the possibility of producing hydrogen. Studying and developing the safety analysis and GCR technologies are required for the optimum design and safety of GCR system. Multiphase Reactors Engineering and Applications Laboratory (mReal) at Missouri University of Science and Technology (S&T) has developed a natural convection heat transfer test facility with one riser …

Computational Fluid Dynamics Modeling And Comparison Of Advanced Techniques For Heat Transfer Augmentation For Nuclear Applications, Salman Mohammed Alzahrani

Doctoral Dissertations

“Passive safety is the most important feature of NuScale’s reactor designs. Twist tape is one passive heat enhance heat technique. The present research investigated thermo-hydraulic characteristics of natural and forced convection of water under different configurations of twisted tape inserted in tube as well as NuScale rod bundles for uniform wall heat flux using computational fluid dynamics (CFD) using ANSYS Fluent 18.1. Results for twist tape inserted in tube under natural circulation showed that heat transfer enhanced and pressure drop increased to 28% and 102.8% over the plain tube respectively. Regularly spaced tapes, and different widths of the twisted tapes …

Towards Sustainable Production Of Chemicals And Fuels From The Fast Pyrolysis Of Waste Polyolefin Plastics, Ulises Gracida Alvarez

Dissertations, Master's Theses and Master's Reports

The increasing amount of plastic waste (PW) generation has become an important concern due to the leveled-off recycling rates. Therefore, governmental agencies around the world, including state governments in the United States, have proposed initiatives to minimize the amount of PW that is landfilled and encourage recycling or energy recovery. Circular economy is a strategy that attempts on reusing PW to produce new polymers while avoiding its disposal and the use of virgin material. Chemical recycling raises an interesting technology prospect due to the potential reduction of pollutant emissions and the establishment of a circular economy through the production of …

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

Void Fraction Measurements In A Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensors And Pressure Transducers: Effect Of Spargers, Afolabi G. Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

Characterization Of Aerosols In An Underground Mine, Arash A. Habibi

Doctoral Dissertations

“Diesel-powered engines are a common source of submicron carbon-rich particles. Characterizing morphological and physical attributes of diesel agglomerates is therefore of great importance to be able to identify the source and improve removal technology. Size-segregated sampling was conducted in two phases of underground experiments. Scanning transmission electron microscopy and fast mobility particle sizers were used to determine the size distribution of agglomerates based on particle mobility and projected area diameter. Controlled zone sampling test results were used to determine the morphological characteristics of agglomerates for specific types of diesel equipment both with and without removal strategies. Changes in fractal dimension, …

Reduction Of Nox Emissions In A Single Cylinder Diesel Engine Using Sncr With In-Cylinder Injection Of Aqueous Urea, Anthony Timpanaro

UNF Graduate Theses and Dissertations

The subject of this study is the effect of in-cylinder selective non-catalytic reduction (SNCR) of NO_x emissions in diesel exhaust gas by means of direct injection of aqueous urea ((NH₂)₂CO) into the combustion chamber. A single cylinder diesel test engine was modified to accept an electronically controlled secondary common rail injection system to deliver the aqueous urea directly into the cylinder during engine operation.

Direct in-cylinder injection was chosen in order to ensure precise delivery of the reducing agent without the risk of any premature reactions taking place. Unlike direct in-cylinder injection of neat water, …