Mechanical Engineering Commons^™

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

University of New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Micro-Architectured Metamaterials: Design And Analysis, Li Ai

Mechanical Engineering Research Theses and Dissertations

Metamaterials are engineered materials with unusual properties deriving mainly from their micro-architectures rather than composition. They have attracted increasing attention owing to their tailorable multi-functional properties that cannot be exhibited by naturally-occurring or traditionally-manufactured materials. Materials with a negative Poisson’s ratio (PR) and materials with a non-positive coefficient of thermal expansion (CTE) are examples of mechanical metamaterials. In this dissertation, metamaterials with negative Poisson’s ratios and negative coefficients of thermal expansion are designed using both heuristic approaches and topology optimization methods.

Firstly, based on a star-shaped re-entrant structure, three two-dimensional (2-D) periodic cellular materials are developed, which can be tailored …

Modeling Of A Head - Neck Assembly Drop Tower Impact Test Using Abaqus, Hussein Sharqi Owaid

Electronic Theses and Dissertations

There are numerous potential causes of traumatic brain injury (TBI) and concussions, including traffic accidents, contact during sports and falls. Protection from these injuries is paramount because of the problems that result from TBI, such as loss of thinking and memory capability. Head impact from falls, especially in elderly, can also result in severe to fatal injury and some effects of brain injury are often not visible. For these reasons and more a need exists for protective head gear that can keep persons safe during at risk physical activity and that can protect fall prone persons from accidental injuries. Part …

Boat-Lift Design And Analysis, Nathan Schick

Honors Theses

A current in production 6000 lb. rated boat-lift is being sold at “Great Lake Lifts”. The lift was tested experimentally and proved to hold at least 8000 lb. The design team successfully modeled the current lift on Ansys to help the customer understand where the weakest points in the design were. Following the creation of the initial lift design, the design team proposed and tested modifications that could be made in order to make the lift more structurally sound. The initial lift had a maximum deflection of 0.43846 inches, a maximum stress of 15880 psi, and a safety factor of …

Dynamic In Vivo Skeletal Feature Tracking Via Fluoroscopy Using A Human Gait Model, William Patrick Anderson

Doctoral Dissertations

The Tracking Fluoroscope System II, a mobile robotic fluoroscopy platform, developed and built at the University of Tennessee, Knoxville, presently employs a pattern matching algorithm in order to identify and track a marker placed upon a subject’s knee joint of interest. The purpose of this research is to generate a new tracking algorithm based around the human gait cycle for prediction and improving the overall accuracy of joint tracking.

This research centers around processing the acquired x-ray images of the desired knee joint obtained during standard clinical operation in order to identify and track directly through the acquired image. Due …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Rogue Rotary - Modular Robotic Rotary Joint Design, Sean Wesley Murphy, Tyler David Riessen, Jacob Mark Triplett

Mechanical Engineering

This paper describes the design process from ideation to test validation for a singular robotic joint to be configured into a myriad of system level of robots.

Usa Boccia Ball Ramp For Athletes With Quadriplegia, Alissa A. Koukourikos, Matthew Lee, Nathan Bernards

Mechanical Engineering

In this report, the design process in creating an assistive device for Boccia Classification 3 (BC3) players is outlined. The initial research steps, including research into the rules of the game, capabilities of the players, and existing products is documented to show where ideas for the product stemmed from. This transitions into requirements that the sponsor requested, and preliminary designs and ideas for the product. Finally, this report explains the details of the final design, which has been analyzed for safety, ease of use, and ability to function under different conditions. The processes of manufacturing and testing will also be …

Multiple Consecutive Recapture Of Rigid Nanoparticles Using A Solid-State Nanopore Sensor, Jungsoo Lee

Mechanical Engineering Research Theses and Dissertations

Solid‐state nanopore sensors have been used to measure the size of a nanoparticle by applying a resistive pulse sensing technique. Previously, the size distribution of the population pool could be investigated utilizing data from a single translocation, however, the accuracy of the distribution is limited due to the lack of repeated data. In this study, we characterized polystyrene nanobeads utilizing single particle recapture techniques, which provide a better statistical estimate of the size distribution than that of single sampling techniques. The pulses and translocation times of two different sized nanobeads (80 nm and 125 nm in diameter) were acquired repeatedly …

Medium Duty Gas-Turbine Engine Blade Removal Tool, Elliott James Greb, Jacob Thomas Syage, Kellen Thomas Field

Mechanical Engineering

Solar Turbines Incorporated sponsored a team of three Cal Poly Undergraduate Mechanical Engineering students to design, manufacture, prototype, and test a tool for the removal of turbine blades from their respective disk assembly without damaging the disk itself. The tool was developed for Solar’s industrial gas turbine engines. The tool complies with all OSHA and Solar Turbines safety and engineering constraints, and was designed for use in a shop facility. The tool was made adaptable for geometric variances in multiple turbine rotor disk stages, and requires no more than one technician to operate using a maximum of two shop resources. …

Development Of A Data Acquisition System For Unmanned Aerial Vehicle (Uav) System Identification, Donald Joseph Lear

Mechanical & Aerospace Engineering Theses & Dissertations

Aircraft system identification techniques are developed for fixed wing Unmanned Aerial Vehicles (UAV). The use of a designed flight experiment with measured system inputs/outputs can be used to derive aircraft stability derivatives. This project set out to develop a methodology to support an experiment to model pitch damping in the longitudinal short-period mode of a UAV. A Central Composite Response Surface Design was formed using angle of attack and power levels as factors to test for the pitching moment coefficient response induced by a multistep pitching maneuver.

Selecting a high-quality data acquisition platform was critical to the success of the …

On The Ramberg-Osgood Stress-Strain Model And Large Deformations Of Cantilever Beams, Ronald J. Giardina Jr

University of New Orleans Theses and Dissertations

In this thesis the Ramberg-Osgood nonlinear model for describing the behavior of many different materials is investigated. A brief overview of the model as it is currently used in the literature is undertaken and several misunderstandings and possible pitfalls in its application is pointed out, especially as it pertains to more recent approaches to finding solutions involving the model. There is an investigation of the displacement of a cantilever beam under a combined loading consisting of a distributed load across the entire length of the beam and a point load at its end and new solutions to this problem are …

Design, Analysis, And Verification Of An Open-Wheeled Formula-Style Race Car Suspension System, Joshua Beckerman

Honors Capstone Projects - All

This honors thesis presents the design, measurement, and analysis of an open-wheeled formula racecar suspension system. This racecar is the second iteration of Syracuse University’s Citrus Racing team student competition vehicle. The race car’s suspension system features several designs that enable geometric adjustability to impact the vehicles dynamic performance. The purpose of this research is to find an analytic approach to verifying the correlation between suspension design tunings and their effect on vehicle handling and road holding capacity. This was done by analyzing measured data obtained from a system of damper-mounted travel sensors as the vehicle drives through numerous realistic …

Value Of Flow Measurement Accuracy In Hydropower Plants With Short Converging Intakes, Mark Herbert Christian

Doctoral Dissertations

This report documents research undertaken to determine the value of flow measurement accuracy in hydropower plants with short converging intakes. The motivation was to provide a suite of tools and best practices to streamline flow measurement sensor modeling in any type of hydropower plant. The Lower Granite Lock and Dam hydroplant was leveraged in development of the analysis tool. Computational fluid dynamics (CFD) models of Lower Granite Unit 4 provided necessary information about the hydraulic structures distribution through the unit. Two different CFD models were created. The first was done using the as-built plans; the second was created through modifications …

Innovation Of Driving Gear Train System For Developer Unit Of Lexmark Home Printers, Jay A. Crist, Sarah Gore, Kun Xie, Michael Mixoon

Chancellor’s Honors Program Projects

No abstract provided.

Design Of A Robotic Instrument Manipulator For Endoscopic Deployment, Ryan Ponten

Masters Theses

This thesis describes the initial design process for an application of continuum robotics to endoscopic surgical procedures, specifically dissection of the colon. We first introduce the long-term vision for a benchtop dual-instrument endoscopic system with intuitive haptic controllers and then narrow our focus to the design and testing of the instrument manipulator itself, which must be actuated through the long, winding channel of a standard colonoscope.

Based on design requirements for a target procedure, we analyze simulations of two types of continuum robots using recently established kinematic and mechanic modeling approaches: the concentric-tube robot (CTR) and the concentric agonist-antagonist robot …

Sae Small Vehicle Lifts, Augustus G. Holz, Nathan K. Harry, Tobias W. Shirts

Mechanical Engineering

The SAE (Society for Automotive Engineers) vehicle teams at Cal Poly need an easy way to access the undersides of their vehicles to facilitate maintenance and servicing. The purpose of this project was to provide a solution that could lift the vehicles effectively and safely from above so that the underside of the vehicles can be accessed, as well as elevating the vehicles to an ergonomic working height. Design specifications were determined based off each vehicle’s requirements in addition to what the team intends to do with their suspended vehicle. After several concept iterations, the team decided to purchase an …

Universal Fixture For Orbital Tube Welding, Kevin P. Mcgowan, William Divittorio, Jesse Castaneda

Mechanical Engineering

No abstract provided.

Drawing And Twisting Of Graphene Fibers, Gregory T. Lane, Robert J. Sekerak, Isaias Diaz

Mechanical Engineering

The aim of this project was to develop a more automated process for drawing and twisting of graphene fibers than was currently in place. This was implemented by having two chemical baths with variable speed rollers at either end, and intermediate roller to spool fiber between stages, and a twisting cylinder with integral spool to twist the fiber as it is collected. The goal was to have this first iteration deliver a working prototype, however due to manufacturing delays and timing constraints, that will be missed. A second follow-on project would be able to continue the work presented here and …

Cal Poly Caramel Counter Top Candy Wrapping Machine, Alexander Miller, Roman Stambaugh, Trevor Steele

Mechanical Engineering

The purpose of this project was to automate the caramel wrapping process for a small batch confectionist. Using a purely mechanical system that is hand-powered, the machine cuts and wraps caramel candies in a double twist fashion.

Collision Mitigation System: Pedestrian Test Target, Final Design Report, Timothy Ryan Lee, Melanie Lim, Tiffany Margaret Prather, Chris Michael Welch

Mechanical Engineering

Daimler Trucks North America is creating an advanced emergency braking system which uses radar sensors that detect pedestrians and automatically applies the brakes to bring the vehicle to a stop. To improve and validate their technology, they need a mechanical pedestrian target that can mimic a human walking across the street. However, the assisted braking may not work properly during every test and the pedestrian target must be able to survive impact with a vehicle at low speeds. Four senior Mechanical Engineering students from California Polytechnic State University San Luis Obispo decided to take on the challenge.

The main features …

Personal Utility Cart, Eric Joseph Johnson, Jason K. Munter, Sean R. Portune

Mechanical Engineering

This final design report will detail the entire engineering design process from conceptualization through manufacturing and testing. After introducing the topic and scope of the project this document presents all of the benchmarking and research performed in order to obtain as much information about similar current products and possible solutions. Next the objectives of the project are presented where the needs are transformed into engineering specifications that will guide the design of the product. Design developed is then presented with ideation, idea evaluation and selection, analysis, manufacturing considerations, and final design selection. The final design is then presented with each …

Full-Scale And Wind Tunnel Investigation Of The Flow Field Over A Coastal Escarpment, Julien Lotufo

Electronic Thesis and Dissertation Repository

A multiscale experimental approach, consisting of full-scale measurements and physical modeling in a laboratory environment, was conducted to investigate the flow field over a coastal escarpment on the Wind Energy Institute of Canada’s research and development wind park. The influence of sea breeze inflow conditions, thermal stability and local topographic features on the flow field were examined.

The results of the full-scale study show that the near surface flow field is significantly influenced by the sea breeze circulatory coastal flow regime, creating larger shear layers with a smaller recirculation regions compared to cases of typical boundary layer flow typical boundary …

Ut Lineman Chute, Benjamin D. Jacob, Logan T. Sissom, Stephen E. Brennan, Thomas B. Mcdavid

Chancellor’s Honors Program Projects

No abstract provided.

Min Kao Autonomous Robot Tour Guide, Albert J. Toth, Sunay G. Bhat, Christopher A. Treadway, Ammar S. Abdelwahed, Samuel C. Leach

Chancellor’s Honors Program Projects

No abstract provided.

Automation In Entertainment: Concept, Design, And Application, Ryan Thally

Undergraduate Honors Theses

The focus of this thesis is to explore the automation technology used in the modern entertainment industry. Upon completion of my thesis, I will deliver a working prototype of the chosen technology and present its capabilities in a choreographed show.

Convection In Corrugated Slots, Seyed Arman Abtahi

Electronic Thesis and Dissertation Repository

This thesis consists of two parts. The first part deals with the development of proper methodology, i.e. a spectrally accurate algorithm suitable for analysis of convection problems in corrugated slots. The second part is devoted to the study of natural convection in corrugated slots.

The algorithm uses the immersed boundary conditions (IBC) concept to deal with the irregular form of the solution domain associated with the presence of corrugated plates. The field equations are discretized on a regular domain surrounding the flow domain using Fourier expansions in the horizontal direction and Chebyshev expansions in the vertical direction. The boundary conditions …

Pin Router Duplicator, Daniel Phan

All Undergraduate Projects

The purpose of this project is to develop a pin router duplicator to accurately produce guitar bodies, necks, and fret boards. The pin router duplicator is designed to speed up the production process for the class Lean Manufacturing (MET 345), offered at Central Washington University. In the class, students learn how to work as a team to improve the way a woodshop is ran. In Lean Manufacturing, guitar bodies, necks, and fret boards are produced by using a CNC router. For this project, the motivation is to increase production by reducing production time. Accuracy and repeatability is also taken into …

High Accessibility Cabinet Insert, Matthew Leal

All Undergraduate Projects

Watching grandparents and parents get older, the struggle of day-to-day activities generally increases. One of the most recurring issues the older generation experiences nearly daily is their inability to reach dishes, glassware, and other things on the topmost shelves of a kitchen. Not only is it difficult for them to use things such as stepstools, it also becomes increasingly dangerous. With age, a fall from any height could be catastrophic. With this scenario in mind, a user-friendly cabinet insert would be a very effective way to combat this issue. However, many existing models of cabinet designed to fit these requirements …

Composite Cold Expansion Tooling, Andrew Amos

All Undergraduate Projects

In the world of aircraft manufacturing, cold expansion products literally hold these aircraft together. The problem faced today is that the Little Brute Hydraulic Puller designed and built by Fatigue Technology Inc. is a handheld steel hydraulic cylinder that is heavy and expensive to produce. In a market that demands continuous improvement, there is a constant push to make the product cheaper, better and lighter. In order to accomplish this demand a composite tube will be substituted in the design as the primary pressure cylinder instead of the traditional steel pressure cylinder in order to create a lighter and cheaper …