Mechanical Engineering Commons^™

One-Dimensional Lateral Force Anisotropy At The Atomic Scale In Sliding Single Molecules On A Surface, Yuan Zhang, Daniel J. Trainer, Badri Narayanan, Yang Li, Anh T. Ngo, Sushila Khadka, Arnab Neogi, Brandon Fisher, Larry A. Curtiss, Subramanian K.R.S. Sankaranarayanan, Saw Wai Hla

Physics Faculty Publications

Using a q+ atomic force microscopy at low temperature, a sexiphenyl molecule is slid across an atomically flat Ag(111) surface along the direction parallel to its molecular axis and sideways to the axis. Despite identical contact area and underlying surface geometry, the lateral force required to move the molecule in the direction parallel to its molecular axis is found to be about half of that required to move it sideways. The origin of the lateral force anisotropy observed here is traced to the one-dimensional shape of the molecule, which is further confirmed by molecular dynamics simulations. We also demonstrate that …

Investigation Of The Tribological Behavior Of Mineral Lubricant Using Copper Oxide Nano Additives, Ahmed A. Abdel-Rehim, Sayed Akl, Sherif Elsoudy

Mechanical Engineering

In this study, tribological properties of custom formulated and stabilized nano lubricant are investigated. Spherical CuO nanoparticles are suspended in 20W-50 mineral base lubricant using Oleic Acid (OA) as a surfactant. Three different nano lubricant concentrations with 0.2, 0.5, and 1 wt.% were analyzed through ASTM G-99 pin-on-disc tribometer standardized test under boundary/mixed lubrication regimes. The generated friction and wear analyses confirm a consolidation of tribological properties with a reduction in friction coefficient in the range of 14.59–42.92%, compared with the base lubricant. Analysis of worn surfaces (SEM/EDX) as well as (AFM) was conducted. Combined hypotheses were proposed from the …

A Bibliometric Analysis Of Ultrasonic Vibration Assisted Turning, Govind S. Ghule, Sudarshan Sanap Prof. Dr.

Library Philosophy and Practice (e-journal)

Ultrasonic vibration-assisted turning (UVAT) is a new crossover in machining techniques which uses high frequency, low amplitude sound waves which are further superimposed on the cutting tool in traditional turning. This innovative technology is being utilized over the decades due to its conspicuous influence contrasted with traditional approach particularly in turning of hard-to-machine materials. This present paper analyses the past explores in the arena of ultrasonic vibration-assisted turning, by a far-reaching bibliometric investigation. The analysis is carried out by scrutinizing the studies through Science Direct and Scopus database to select the peer-reviewed papers. The advanced research tools like the word …

Modeling Residual Stress Development In Hybrid Processing By Additive Manufacturing And Laser Shock Peening, Guru Charan Reddy Madireddy

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The term “hybrid” has been widely applied to many areas of manufacturing. Naturally, that term has found a home in additive manufacturing as well. Hybrid additive manufacturing or hybrid-AM has been used to describe multi-material printing, combined machines (e.g., deposition printing and milling machine center), and combined processes (e.g., printing and interlayer laser re-melting). The capabilities afforded by hybrid-AM are rewriting the design rules for materials and adding a new dimension in the design for additive manufacturing paradigm. This work focuses on hybrid-AM processes, which are defined as the use of additive manufacturing (AM) with one …

Mechanical Wear Debris Feature, Detection, And Diagnosis: A Review, Wei Hong, Wenjian Cai, Shaoping Wang, Mileta M. Tomovic

Engineering Technology Faculty Publications

Mechanical debris is an important product of friction wear, which is also a crucial approach to know the running status of a machine. Many studies have been conducted on mechanical debris in related fields such as tribology, instrument, and diagnosis. This paper presents a comprehensive review of these studies, which summarizes wear mechanisms (e.g., abrasive wear, fatigue wear, and adhesive wear) and debris features (e.g., concentration (number), size, morphology, and composition), analyzes detection methods principles (e.g., offline: spectrograph and ferrograph, and online: optical method, inductive method, resistive-capacitive method, and acoustic method), reviews developments of online inductive methods, and investigates the …

Erosion Degradation Characteristics Of A Linear Electro-Hydrostatic Actuator Under A High-Frequency Turbulent Flow Field, Yuan Li, Shaoping Wang, Mileta M. Tomovic, Chao Zhang

Engineering Technology Faculty Publications

The paper proposes a performance degradation analysis model based on dynamic erosion wear for a novel Linear Electro-Hydrostatic Actuator (LEHA). Rather than the traditional statistical methods based on degradation data, the method proposed in this paper firstly analyzes the dominant progressive failure mode of the LEHA based on the working principle and working conditions of the LEHA. The Computational Fluid Dynamics (CFD) method, combining the turbulent theory and the micro erosion principle, is used to establish an erosion model of the rectification mechanism. The erosion rates for different port openings, under a time-varying flow field, are obtained. The piecewise linearization …

In-Vivo Corrosion And Fretting Of Modular Ti-6al-4v/Co-Cr-Mo Hip Prostheses: The Influence Of Microstructure And Design Parameters, Jose Luis Gonzalez Jr

FIU Electronic Theses and Dissertations

The purpose of this study was to evaluate the incidence of corrosion and fretting in 48 retrieved titanium-6aluminum-4vanadium and/or cobalt-chromium-molybdenum modular total hip prosthesis with respect to alloy material microstructure and design parameters. The results revealed vastly different performance results for the wide array of microstructures examined. Severe corrosion/fretting was seen in 100% of as-cast, 24% of low carbon wrought, 9% of high carbon wrought and 5% of solution heat treated cobalt-chrome. Severe corrosion/fretting was observed in 60% of Ti-6Al-4V components. Design features which allow for fluid entry and stagnation, amplification of contact pressure and/or increased micromotion were also shown …

A Comparison Between Graphene And Ws2 As Solid Lubricant Additives To Aluminum For Automobile Applications, Sara Rengifo

FIU Electronic Theses and Dissertations

The purpose of this thesis was to compare graphene nanoplatelets (GNP) and WS₂ as solid lubricant additives to aluminum in order to reduce friction and wear. The central hypothesis of this work relied on lubricating properties of 2D materials, which consist layers that slip under a shear force.

Two aluminum composites were made (Al-2 vol.% GNP and Al-2 vol.% WS₂) by spark plasma sintering. Tribological properties were evaluated by ball-on-disk wear tests at room temperature (RT) and 200^°C.

WS₂ not only presented the lowest COF (0.66) but also improved the wear resistance of aluminum …

Acoustic Emission Detection Of Metals And Alloys During Machining Operations, Jameson K. Nelson

Purdue Polytechnic Masters Theses

Nelson, Jameson K. M.S., Purdue University, May 2012. Acoustic Emission Detection of Metals and Alloys During Machining Operations. Major Professor: Rodney G. Handy.

Practical correlation between material deformation attributes and theoretical concepts of machining has proven difficult to attain. The purpose of this study was to further explore trends and relationships using acoustic emission detection of materials undergoing single-point lathe turning machine processes. The majority of machining experiments that incorporate acoustic emissions focuses on tool degradation for the purposes of optimizing consumables required to manufacture mechanical devices. Experiments were implemented varying recording location, mechanical barrier condition, and machine parameters. The …

Investigating Polymer-Tool Steel Interfaces To Predict The Work Of Adhesion For Demoulding Force Optimisation, Kevin Delaney, David Kennedy, Giuliano Bissacco

Conference Papers

Demoulding parts from replication tools is a critical stage of replication processes such as injection moulding and hot embossing. This challenge increases as part size decreases since components and associated replication cores become more fragile and liable to damage. Understanding interfacial characteristics between a polymer and the tool surface is critical to optimise the demoulding of such parts from replication tools. The strength of the polymer-tool interaction is characterised by the adhesion energy and is specific for a particular polymer-tool pair. It’s magnitude depends upon the tool material, the chemical structure of the polymer, the processing conditions and the surface …

Some Considerations For Regional Airline Operations On Contaminated Runways., Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Identification Of Multiple Oscillation States Of Carbon Nanotube Tipped Cantilevers Interacting With Surfaces In Dynamic Atomic Force Microscopy, Mark Strus, Arvind Raman

Birck and NCN Publications

Carbon nanotubes (CNTs) have gained increased interest in dynamic atomic force microscopy (dAFM) as sharp, flexible, conducting, nonreactive tips for high-resolution imaging, oxidation lithography, and electrostatic force microscopy. By means of theory and experiments we lay out a map of several distinct tapping mode AFM oscillation states for CNT tipped AFM cantilevers: namely, noncontact attractive regime oscillation, intermittent contact with CNT slipping or pinning, or permanent contact with the CNT in point or line contact with the surface while the cantilever oscillates with large amplitude. Each state represents fundamentally different origins of CNT-surface interactions, CNT tip-substrate dissipation, and phase contrast …

Localised Galvanic Corrosion Processes In Thermal Spray Coated/Cast Aluminium Alloy Systems, David Culliton, Tony Betts, David Kennedy

Conference Papers

Cast Aluminium Alloys, because of the propensity of aluminium to react with impurities and alloying elements, are prone to developing IM impurities during the solidification process. These IM phases can act, in some fluids, as initiation sites for localised corrosion processes, resulting in degradation phenomena, such as pitting. Whilst Thermal Spray coatings can improve the wear resistance of Cast Aluminium Alloys, their corrosion performance may be hampered by the presence of through porosity within the coating.

The present work details some preliminary studies of the localised corrosion processes occurring at the interface area between a Thermal Spray coating and a …