Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 7 of 7
Full-Text Articles in Mechanical Engineering
Estimating The Inner Ring Defect Size And Residual Service Life Of Freight Railcar Bearings Using Vibration Signatures, Jennifer Lima, Constantine Tarawneh, Jesse Aguilera, Jonas Cuanang
Estimating The Inner Ring Defect Size And Residual Service Life Of Freight Railcar Bearings Using Vibration Signatures, Jennifer Lima, Constantine Tarawneh, Jesse Aguilera, Jonas Cuanang
Mechanical Engineering Faculty Publications and Presentations
There are currently two primary wayside detection systems for monitoring the health of freight railcar bearings in the railroad industry: The Trackside Acoustic Detection System (TADS™) and the wayside Hot-Box Detector (HBD). TADS™ uses wayside microphones to detect and alert the train operator of high-risk defects. However, many defective bearings may never be detected by TADS™ since a high-risk defect is a spall which spans about 90% of a bearing’s raceway, and there are less than 30 systems in operation throughout the United States and Canada. HBDs sit on the side of the rail-tracks and use non-contact infrared sensors to …
Optimization Of Railroad Bearing Health Monitoring System For Wireless Utilization, Jonas Cuanang, Constantine Tarawneh, Martin Amaro Jr., Jennifer Lima, Heinrich D. Foltz
Optimization Of Railroad Bearing Health Monitoring System For Wireless Utilization, Jonas Cuanang, Constantine Tarawneh, Martin Amaro Jr., Jennifer Lima, Heinrich D. Foltz
Mechanical Engineering Faculty Publications and Presentations
In the railroad industry, systematic health inspections of freight railcar bearings are required. Bearings are subjected to high loads and run at high speeds, so over time the bearings may develop a defect that can potentially cause a derailment if left in service operation. Current bearing condition monitoring systems include Hot-Box Detectors (HBDs) and Trackside Acoustic Detection Systems (TADS™). The commonly used HBDs use non-contact infrared sensors to detect abnormal temperatures of bearings as they pass over the detector. Bearing temperatures that are about 94°C above ambient conditions will trigger an alarm indicating that the bearing must be removed from …
Prototyping A Conductive Polymer Steering Pad For Rail Freight Service, Anthony A. Villarreal, Constantine Tarawneh, Miguel Ontiveros, James Aranda, Robert Jones
Prototyping A Conductive Polymer Steering Pad For Rail Freight Service, Anthony A. Villarreal, Constantine Tarawneh, Miguel Ontiveros, James Aranda, Robert Jones
Mechanical Engineering Faculty Publications and Presentations
The AdapterPlus™ steering pad is a polymer component on a railcar that helps to reduce stresses on the axle as a railcar rounds a curve. One railway application requires a minimum of 240 mA to be passed through the steering pad to the rail, which activates air valves that control automated cargo gates. Currently, two copper studs are inserted into the pad to provide a conductive path. However, after continuous cyclic loading caused by normal service operation, the copper studs deform, wear, and eventually lose contact between the two surfaces rendering the pad nonconductive. One proposed solution to this problem …
Estimating The Outer Ring Defect Size And Remaining Service Life Of Freight Railcar Bearings Using Vibration Signatures, Joseph Montalvo, Constantine Tarawneh, Jennifer Lima, Jonas Cuanang, Nancy De Los Santos
Estimating The Outer Ring Defect Size And Remaining Service Life Of Freight Railcar Bearings Using Vibration Signatures, Joseph Montalvo, Constantine Tarawneh, Jennifer Lima, Jonas Cuanang, Nancy De Los Santos
Mechanical Engineering Faculty Publications and Presentations
The railroad industry currently utilizes two wayside detection systems to monitor the health of freight railcar bearings in service: The Trackside Acoustic Detection System (TADS™) and the wayside Hot-Box Detector (HBD). TADS™ uses wayside microphones to detect and alert the conductor of high-risk defects. Many defective bearings may never be detected by TADS™ since a high-risk defect is a spall which spans more than 90% of a bearing’s raceway, and there are less than 20 systems in operation throughout the United States and Canada. Much like the TADS™, the HBD is a device that sits on the side of the …
Vibration-Based Defect Detection For Freight Railcar Tapered-Roller Bearings, Joseph Montalvo, Constantine Tarawneh, Arturo A. Fuentes
Vibration-Based Defect Detection For Freight Railcar Tapered-Roller Bearings, Joseph Montalvo, Constantine Tarawneh, Arturo A. Fuentes
Mechanical Engineering Faculty Publications and Presentations
The railroad industry currently utilizes two wayside detection systems to monitor the health of freight railcar bearings in service: The Trackside Acoustic Detection System (TADS™) and the wayside Hot-Box Detector (HBD). TADS™ uses wayside microphones to detect and alert the conductor of high risk defects. Many defective bearings may never be detected by TADS™ due to the fact that a high risk defect is considered a spall which spans more than 90% of a bearing’s raceway, and there are less than 20 systems in operation throughout the United States and Canada. Much like the TADS™, the HBD is a device …
Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Element, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh, Robert E. Jones
Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Element, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh, Robert E. Jones
Mechanical Engineering Faculty Publications and Presentations
Thermoplastic elastomers (TPE’s) are increasingly being used in rail service in load damping applications. They are superior to traditional elastomers primarily in their ease of fabrication. Like traditional elastomers they offer benefits including reduction in noise emissions and improved wear resistance in metal components that are in contact with such parts in the railcar suspension system. However, viscoelastic materials, such as the railroad bearing thermoplastic elastomer suspension element (or elastomeric pad), are known to develop self-heating (hysteresis) under cyclic loading, which can lead to undesirable consequences. Quantifying the hysteresis heating of the pad during operation is therefore essential to predict …
Heat Generation In The Railroad Bearing Thermoplastic Elastomer Suspension Element, Oscar O. Rodriguez, Juan Carbone, Arturo A. Fuentes, Robert E. Jones, Constantine Tarawneh
Heat Generation In The Railroad Bearing Thermoplastic Elastomer Suspension Element, Oscar O. Rodriguez, Juan Carbone, Arturo A. Fuentes, Robert E. Jones, Constantine Tarawneh
Mechanical Engineering Faculty Publications and Presentations
The main purpose of this ongoing study is to investigate the effect of heat generation within a railroad thermoplastic elastomer suspension element on the thermal behavior of the railroad bearing assembly. Specifically, the purpose of this project is to quantify the heat generated by cyclic loading of the elastomer suspension element as a function of load amplitude, loading frequency, and operating temperature. The contribution of the elastomer pad to the system energy balance is modeled using data from dynamic mechanical analysis (DMA) of the specific materials in use for that part. DMA is a technique that is commonly used to …