Mechanical Engineering Commons^™

Reliability Study Of A New Electromechanical Device Designed To Measure The Relative Dorsal Mobility Of The First Ray Of The Foot, Philippe Passeraub

Faculty Publications

Introduction: A new electromechanical instrument has been developed to measure relative dorsal mobility of the first ray in an objective and reliable way by simulating ground reaction forces during gait. This device equally applies a standardized, electronically controlled, and precise force under the first metatarsal head M1 as well as under the heads of the lesser metatarsals M2 to M5. The relative dorsal mobility between these two bearings is then measured. The purpose of this study is to assess the intra- and inter-examiners reliabilities of the measurements obtained with this device. Methods: The protocol included two examiners and 36 feet …

Trade-Off Characterization Between Social And Environmental Impacts Using Agent-Based Models And Life-Cycle Assessment, Joseph C. Leichty, Christopher S. Mabey, Christopher A. Mattson, John L. Salmon, Jason Weaver

Faculty Publications

Meeting the UN’s sustainable development goals requires designers and engineers to solve multi-objective optimization problems involving trade-offs between social, environmental, and economic impacts. This paper presents an approach for designers and engineers to quantify the social and environmental impacts of a product at a population-level and then perform a trade-off analysis between those impacts. In the approach, designers and engineers define the attributes of the product as well as the materials and processes used in the product’s life cycle. Agent-Based Modeling (ABM) tools that have been developed to model the social impacts of products are combined with Life- Cycle Assessment …

A Comparison Of Layer Deposition And Open Molding Of Petg By Fused Pellet Fabrication In An Additive Manufacturing System, Alex Gibson, Jason Weaver

Faculty Publications

Additive manufacturing continues to offer new possibilities in both production and economics. The industry has quickly adopted it to rapidly produce parts that would be difficult or cost preventative otherwise. Recent innovation has expanded its capabilities, however there are still significant limitations. Most AM processes are restricted by materials available, in producing large parts, or by not achieving material deposition speeds to make certain products feasible. In addition, tight tolerances for features and surfaces cannot be produced without substantial post processing. High-speed Fused Pellet Fabrication (FPF) in combination with Hybrid Manufacturing (HM) offers expanded capabilities as additive and subtractive process …

Optimizing Build Plate Adhesion Of Polymers In Fused Granule Fabrication Processes, Alex Schroeder, Jason Weaver

Faculty Publications

Perhaps the most crucial element of fused granule fabrication (FGF) is material adhesion; in order to achieve a successful product, the material being printed must adhere to the build plate. For optimal products, the material should only adhere to the build plate until the print is complete, then be easily removable. This paper examines the effects of different build plates, environments, and bonding agents on material adhesion during the FGF process in a CNC mill machine. The force to remove polycarbonate (PC) and polypropylene (PP) from build plates was tested with various bonding agents. Except in one case, the adhesive …

Closed Loop Recycling Of Low Friction Polymers In Fused Granule Fabrication Additive Manufacturing Processes, Neil Thompson, Jason Weaver

Faculty Publications

Plastic waste is a critical worldwide problem that impacts additive manufacturing (AM). Extensive research has explored how plastic waste in AM can be reduced by recycling prints into new filament, with varying success. An alternative to filament-based extrusion is “fused granule fabrication” (FGF), which extrudes from pellets or granules. This method is often used for large area additive manufacturing (LAAM) of polymers. This paper expands upon the knowledge base from previous research on LAAM and examines the extent to which PETG can be recycled and reprinted through the same FGF tool without significant loss to its material properties. The metric …

Durability Of Vacuum Infusion Tooling Produced From Fused Granular Fabrication Additive Manufacturing, Nathan Northrup, Jason Weaver, Andy R. George

Faculty Publications

Large area additive manufacturing (LAAM) has the capability to create tooling that is lower cost than conventionally manufactured tooling and still has sufficient properties for many applications. A vacuum infusion mold was printed from fiberglass-ABS and evaluated for wear and suitability for small vacuum infusion runs. The mold was designed to accentuate high wear as a “worst case” scenario. The mold was able to produce 10 parts successfully before any noticeable change occurred to the surface finish. By 14 parts, the surface finish had roughened sufficiently that demolding was difficult and resulted in damage to the part. Profilometry measurements showed …

A High-Pressure Shear Testing Approach To Measure Flow Stresses Near A Friction Stir Welding Tool, David Prymak, Michael Miles, Tracy W. Nelson, Fredrick Michael

Faculty Publications

A new approach for measuring flow stresses near a spinning friction stir welding (FSW) tool is evaluated on AA 6061-T6 plate. The test consists of plunging a cylindrical tool with a flat face into the plate at different rotational speeds, using a variety of constant vertical loads. A viscosity-based model of the shear layer created under the tool is employed to estimate local flow stresses. The flow stresses measured by this approach exhibited an inverse relationship with temperature and a positive dependence on the pressure imposed by the spinning flat-faced tool. Compared to hot compression and hot torsion results, estimated …

Vacuum Infusion Of Composites: Durability Of Hybrid Large Area Additive Tooling For Vacuum Infusion Of Composites, Nathan Northrup, Jason Weaver, Andy R. George

Faculty Publications

The durability of a hybrid large area additively manufactured fiberglass ABS mold for vacuum infusion of composites was evaluated. The validation was done by designing and fabricating a mold for a custom test artifact and analyzing the surface geometry over the course of multiple infusions until tool failure. After printing and machining, the mold required a sealer to maintain vacuum integrity. The mold was able to produce 10 parts successfully before the sealed tool surface began to tangibly roughen, resulting in increased difficulty of demolding and a rougher surface finish. After the 14th infusion, the part required destructive force to …

Spectral Absorption Coefficient Of Additive Manufacturing Materials, Nicholas J. Wallace, Matthew R. Jones, Nathan B. Crane

Faculty Publications

Active thermography techniques are of interest for quality assurance of additive manufacturing processes. However, accurate measurements of thermophysical properties of materials are required to successfully implement active thermography. In particular, the spectral absorption coefficient of materials commonly used in additive manufacturing must be known to accurately predict the spatial distribution of thermal energy generated from absorption of power emitted by a laser or pulsed flash lamp. Accurate measurements of these optical properties are also needed to develop greater understanding of additive manufacturing processes that rely on radiative heat transfer to fuse powders. This paper presents spectral absorption coefficient measurements and …

Impact Of Sintering Time And Temperature On Mechanical Properties In Projection Sintering Of Polyamide-12, Justin Nussbaum, Taranjot Kaur, Julie Harmon, Nathan B. Crane

Faculty Publications

In powder bed fusion additive manufacturing (AM), the fusing process is temperature and time dependent. However, little work has been done to understand how different processing temperatures and times might impact the mechanical properties at longer sintering times than are typical in laser sintering (LS) systems. Prior results with projection sintering have shown that heating for longer times (>1s) improves part toughness compared to laser sintering. In this work, Large Area Projection Sintering (LAPS) is used to sinter entire layers of material simultaneously over the course of a few seconds with spatial control of layer temperature. This work evaluates …

Impact Of Part Thickness And Drying Conditions On Saturation Limits In Binder Jet Additive Manufacturing, Nathan B. Crane

Faculty Publications

Binder jetting (BJ) is a high build-rate additive manufacturing process with growing commercial interest. Growth in BJ applications is driven by the use of finer powders and improved post-processing methods that can produce dense, homogenous final parts. However, understanding of the basic droplet/powder interaction is relatively limited. This paper considers the impact of in-process drying, part geometry, and droplet size on a key printing parameter: binder saturation. Parts of varying thicknesses are printed with a range of saturation levels under various heating conditions. The ratio of the printed part mass to the theoretical part mass is used to detect bleeding. …

Influence Of Droplet Velocity, Spacing, And Inter-Arrival Time On Line Formation And Saturation In Binder Jet Additive Manufacturing, Trenton Colton, Nathan B. Crane

Faculty Publications

Binder Jetting (BJ) is a low-cost Additive Manufacturing (AM) process that uses inkjet technology to selectively bind particles in a powder bed. BJ relies on the ability to control, not only the placement of binder on the surface but also its imbibition into the powder bed. This is a complex process in which picoliter-sized droplets impact powder beds at velocities of 1-10 m/s. However, the effects of printing parameters such as droplet velocity, size, spacing, and inter-arrival time on saturation level (fraction of pore space filled with binder) and line formation (merging of droplets to form a line) are unknown. …

Adhesion Testing Of Printed Inks While Varying The Surface Treatment Of Polymer Substrates, Clayton Neff, Edwin Elston, Amanda Schrand, Nathan B. Crane

Faculty Publications

Additive manufacturing with conductive materials enables new approaches to printed electronics that are unachievable by standard electronics manufacturing processes. In particular, electronics can be embedded directly into structural components in nearly arbitrary 3D space. While these methods incorporate many of the same materials, the new processing methods require standard test methods to compare materials, processing conditions, and determine design limits. This work demonstrates a test method to quantitatively measure the adhesion failure of printed inks deposited on a substrate without changing the ink printing conditions. The proposed method is an adaption of single lap shear testing in which the lap …

Mechanical And Temperature Resilience Of Multi-Material Systems For Printed Electronics Packaging, Clayton Neff, Justin Nussbaum, Chris Gardiner, Nathan B. Crane, James L. Zunino, Mike Newton

Faculty Publications

In this work, two AM technologies were utilized to compare the effectiveness of fabricating a simple electronic device with a conductive trace and hollow cylinder representative of ‘printed packaging’ that would survive harsh environmental conditions. The printed packaging cylinder delineates printed potting for electronics packaging. An nScrypt direct write (DW) system was the primary manufacturing system but a developing technology—coined large area projection sintering (LAPS)—manufactured a subset of samples for comparison. The tests follow Military Standard (MIL STD) 883K and include resiliency evaluation for die shear strength, temperature cycling, thermal shock, and high G loading by mechanical shock. Results indicate …

Wetting Metamorphosis Of Hydrophobic Fluoropolymer Coatings Submerged In Water And Ultrasonically Vibrated, Matthew Trapuzzano, Nathan B. Crane, Rasim Guldiken, Andrés Tejada-Martínez

Faculty Publications

Many important processes, from manufacture of integrated circuit boards, to an insect’s ability to walk on water, depend on the wetting of liquids on surfaces. Wetting is commonly controlled through material selection, coatings, and/or surface texture. However, wetting is sensitive to environmental conditions. In particular, some hydrophobic fluoropolymer coatings are sensitive to extended water exposure as evidenced by a declining contact angle and increasing contact angle hysteresis. Understanding “degradation” of these coatings is critical to applications that employ them. The durability of a series of fluoropolymer coatings were tested by measuring the contact angle before, during, and after extended submersion …

Binder Jetting: A Review Of Process, Materials, And Methods, Mohsen Ziaee, Nathan B. Crane

Faculty Publications

Binder Jet printing is an additive manufacturing technique that dispenses liquid binding agent on powder. Layers are formed repeatedly to build up a physical article. Binder jetting (BJ) can be adapted to almost any powder with high production rates. The BJ process utilizes a broad range of technologies including printing methods, powder deposition, dynamic binder/powder interaction, and post-processing methods. A wide variety of materials have been demonstrated including polymers, metals, and ceramics, but a common challenge is developing printing and post-processing methods that maximize part performance. This article presents a broad review of technologies and approaches that have been applied …

Experimental And Theoretical Investigation Of Mechanical Response Of Laser-Sintered Diamond Lattice Structures, Clayton Neff, Neil Hopkinson, Nathan B. Crane

Faculty Publications

Typically additive manufacturing (AM) processes are limited to a single material per part while many products benefit from the integration of multiple materials with varied properties. To achieve the benefits of multiple materials, the geometric freedom of AM could be used to build internal structures that emulate a range of different material properties such as stiffness, Poisson’s ratio, and elastic limit using only one build material. This paper examines the range of properties that can be simulated using diamond lattice structures manufactured from Nylon 12 with a commercial laser sintering process. Diamond lattices were fabricated with a unit cell length …

Impact Of Extended Sintering Times On Mechanical Properties In Pa-12 Parts Produced By Powderbed Fusion Processes, Garrett Craft, Justin Nussbaum, Nathan B. Crane, J. P. Harmon

Faculty Publications

Additive Manufacturing provides many advantages in reduced lead times and increased geometric freedom compared to traditional manufacturing methods, but material properties are often reduced. This paper considers powder bed fusion of polyamide 12 (PA12, Nylon 12) produced by three different processes: laser sintering (LS), multijet fusion (MJF)/high speed sintering (HSS), and large area projection sintering (LAPS). While all utilize similar PA12 materials, they are found to differ significantly in mechanical properties especially in elongation to break. The slower heating methods (MJF/HSS and LAPS) produce large elongation at break with the LAPS process showing 10x elongation and MJF/HSS exhibiting 2.5x the …

Binder-Jet Printing Of Fine Stainless Steel Powder With Varied Final Density, Mohsen Ziaee, Eric M. Tridas, Nathan B. Crane

Faculty Publications

Binder jetting is an additive manufacturing process that produces relatively weak porous parts that are strengthened through sintering and/or infiltration. This paper reports on two different methods of preparing fine 316 stainless steel powder and their impact on the final sintered density and dimensions relative to direct printing into -22 micron powder. The first method uses agglomerates of fine powder. In the second, nylon 12 powders are mixed with the steel powder as a fugitive space holder to increase porosity. Sintered density and sintering shrinkage of agglomerate material are shown to vary with the density of the spread powder bed. …

Eliminating The Illusion Of Learning From Engineering Courses, Jason Weaver

Faculty Publications

This paper describes the efforts of the author to incorporate tools into an undergraduate engineering course to help facilitate better learning and assess proficiency more effectively by avoiding the illusion of learning. Several techniques are used, including suggestions from the recent book Make It Stick by Brown, Roediger, and McDaniel. Student feedback and instructor observations are discussed, and future recommendations for the course are given

Stress-Limiting Test Structures For Rapid Low-Cost Strength And Stiffness Assessment, Andrew Katz, Craig P. Lusk, Nathan B. Crane

Faculty Publications

Purpose: Evaluate the use of a simple printed geometry to estimate mechanical properties (elastic modulus, yield strength) with inexpensive test equipment.

Design Methodology/Approach: Test geometry is presented that enables controlled strains with manual deformation and repeatable measurement of vibrational frequencies. This is tested with multiple FDM machines to assess measurement accuracy and repeatability. Printing orientation and some printing parameters are varied to assess the measurement sensitivity.

Findings: The test methods show good correlation with manufacturer material specifications in the X-Y plane and reported elastic strain limits. It is also sensitive to printing orientation and printing parameters.

Research Limitations/Implications: Further work …

Self Assembly In Additive Manufacturing: Opportunities And Obstacles, Nathan B. Crane, J. Tuckerman, G. N. Nielson

Faculty Publications

Purpose

Additive manufacturing offers substantial flexibility in shape, but much less flexibility in materials and functionality—particularly at small size scales. A system for automatically incorporating microscale components would enable the fabrication of objects with more functionality. This paper considers the potential of self assembly to serve as an automated programmable integration method. In particular, it addresses the ability of random self assembly processes to successfully assemble objects with high performance despite the possibility of assembly errors.

Methodology

A self-assembled thermoelectric system is taken as a sample system. The performance expectations for these systems are then predicted using modified one-dimensional models …