Mechanical Engineering Commons^™

Development Of A Computationally Efficient Method For Modelling Thermal Energy Storage In Packed Beds Of Spherically Encapsulated Phase Change Material, Colin Jaffray

Electronic Thesis and Dissertation Repository

A novel computationally efficient method for modelling melting and solidification processes in packed beds of PCM encapsulated spheres is introduced. The proposed method involves the full discretization of only one centrally located sphere to fully simulate the phase change process, while treating all other spheres in the packed bed as voids with boundary conditions derived from the simulated sphere. At each time step, the computed heat transfer parameters on the exterior surface of the simulated sphere undergoing the phase change process are extracted, and imposed as boundary conditions on surrounding spheres. The proposed method results in a significant reduction in …

Diffusion-Dependent Electrodes For All-Solid-State Lithium-Ion Batteries, Peiman Mardani

Electronic Thesis and Dissertation Repository

Electrode design, which is closely related to electronic and ionic transport, has a significant impact on all-solid-state batteries' performance. Typically, a combination of the active material and solid electrolyte serves as the electrode for all-solid-state batteries. An effective scaling technique to spatially organize the two components is essential for high-performance all-solid-state batteries. Here, an electrode design for all-solid-state batteries is given with a higher energy density than the typical composite-type electrode. The first section of the thesis presents a simple electrode design that primarily consists of blended active materials of graphite and phosphorus to meet the demands of all-solid-state batteries …

Quantification Of Flows Emerging From Small Pores In Plane Walls, Matia Peter Edwards

Electronic Thesis and Dissertation Repository

Current membrane separation processes are limited in high production and high purity settings due to a trade-off between selectivity and permeance. Methods of creating nanoscale geometries in 2D materials are emerging and present an opportunity for fast, size selective mass transport that can be tailored to a wide array of applications. This thesis develops a method for quantifying flow through small pores in plane walls based on the behaviour of a solute dispersed in a downstream reservoir. This method is validated for a range of micropore diameters, for which flow rates can be calculated with confidence, and is shown to …

Pressure Drop And Heat Transfer In Flow Over An Array Of Blocks Of Varying Heights: A Statistical And Ai Analysis On The Effect Of Block Height Variation, Ali Navidi

Electronic Thesis and Dissertation Repository

The presence of a stiff obstruction in the path of fluid causes the creation of a boundary layer over and around the obstruction. The flow over an idealized, two-dimensional series of blocks is numerically investigated to determine how statistical blocks height variation, such as standard deviation, mean, and skewness, influence pressure drop and heat flux. These data sets serve as a foundation for developing models for estimating the heat transfer coefficient of each block using machine learning (ML) methods. The results show that the pressure drop increased by 60% when the standard deviation of heights of blocks increased from 0.1 …

A Numerical Method For Studying The Effectiveness Of Polyurethane Foam As Personal Protective Equipment Material, Lamia Tahsin Aroni

Electronic Thesis and Dissertation Repository

This thesis documents the characterization of flexible polyurethane foam (FPF) to be used as a personal protective equipment material. Polyurethane samples were tested experimentally to calculate the physical properties which were later re-created using a numerical model. A discrete element modeling software was used to generate the geometry to mimic the physical properties of FPF. The pore level numerical model was used to calculate the possible rate of particle penetration for a range (0.2 -200) µm of particle sizes. A parametric study was done using the polyurethane foam parameters to understand the breathing dynamics under steady conditions. The possible particle …

A Framework For Stable Robot-Environment Interaction Based On The Generalized Scattering Transformation, Kanstantsin Pachkouski

Electronic Thesis and Dissertation Repository

This thesis deals with development and experimental evaluation of control algorithms for stabilization of robot-environment interaction based on the conic systems formalism and scattering transformation techniques. A framework for stable robot-environment interaction is presented and evaluated on a real physical system. The proposed algorithm fundamentally generalizes the conventional passivity-based approaches to the coupled stability problem. In particular, it allows for stabilization of not necessarily passive robot-environment interaction. The framework is based on the recently developed non-planar conic systems formalism and generalized scattering-based stabilization methods. A comprehensive theoretical background on the scattering transformation techniques, planar and non-planar conic systems is presented. …

Development Of A Two-Axis Cyclic Loading Device For Mechanical Testing Of Glenoid Component Fixation, Cintya Tavares

Electronic Thesis and Dissertation Repository

The fundamental mechanism of aseptic glenoid component loosening, the rocking horse phenomenon, is a reaction to glenohumeral articular forces that are not centered on the component. While glenoid component loosening remains a problem, the underlying mechanisms that lead to fixation failure at the bone-component contact remain controversial. Several studies employing the ASTM F2028 technique have successfully recreated the rocking horse effect. However, no obvious strategy to decrease component loosening has been presented. This thesis investigates the behavior of forces that lead to component loosening on cyclically loaded components using three different protocols and testing apparatuses—a Stewart Platform, a cyclic loading …

Numerical Investigation Of Flow And Thermal Behavior In Channels With Pcm-Filled Thermal Energy Storage Columns For Potential Application In Photobioreactors, Sameed Akber

Electronic Thesis and Dissertation Repository

Microalgae has been identified as a potential source in the production of biofuel. Photobioreactors, which are used for microalgae production, normally experience temperature variations over the diurnal cycle due to changes in ambient conditions. The thermal regulation of photobioreactors to minimize temperature variations will result in a higher yield of microalgae, which are sensitive to such variations. The present research is aimed to investigate a novel approach to thermally regulate photobioreactors using phase change materials (PCM) where the latent heat of the material is exploited as the energy storage. The present research uses a numerical approach to study the flow …

Project Khepri: Mining Asteroid Bennu For Water, Erika Frost, Gowtham Boyala, Adam Gremm, Ahmet Gungor, Amirhossein Taghipour, Massimo Biella, Jiawei "Jackson" Qiu, Athip Thirupathi Raj, Arjun Chhabra, Adam Gee, Saanjali Maharaj, Erin Richardson, Julia Empey, Haidar Ali Abdul-Nabi, Lindsay Richards, Ariyaan Talukder, Aaron Groh, Brie Miklaucic, Jd Carlson, Kristina Kim, Maverick Cue

Undergraduate Student Research Internships Conference

Deep space asteroid mining presents the opportunity for the collection of critical resources required to establish a cis-lunar infrastructure. In specific, the Project Khepri team has focused on the collection of water from asteroid Bennu. This water has the potential to provide a source of clean-energy propellant as well as an essential consumable for humans or agriculture on crewed trips to the Moon or Mars. This would avoid the high costs of launching from Earth - making it a highly desirable element for the future of cis-lunar infrastructure. The OSIRIS-REx mission provided a complete survey of asteroid Bennu and is …

The Design And Evaluation Of A Subacromial Implant In Restoring Normal Glenohumeral Joint Stability In The Presence Of A Massive Irreparable Rotator Cuff Tear, Cole T. Fleet

Electronic Thesis and Dissertation Repository

Massive irreparable rotator cuff tears are a common cause of pain and disability. Several different treatment options are available for this pathology; however, these treatments have been associated with poor clinical outcomes when used to treat younger (<65 years), more active patients. The purpose of this thesis was to design and evaluate a subacromial implant in its ability to restore normal glenohumeral stability and range of motion. The implant was created as a modular device, which captured different implant thicknesses (5mm and 8mm) and constraints (high and low) within its design. In-vitro testing compared the ability of these implants to restore normal shoulder biomechanics. The results indicated the 5mm high constraint implant to be the most effective in restoring normal joint position. Furthermore, range of motion increased when the implant was paired with a tuberoplasty procedure. These results suggest this implant may be advantageous in treating younger patients.

Numerical Analysis Of Internal Hydraulic Jump In Complex Topography, Dylan Macriner

Electronic Thesis and Dissertation Repository

Topographic effects on internal hydraulic jumps in stratified flow over complex geometry are studied. The simulations are motivated by flow conditions present in a channel in Hood Canal, Washington with continuous density profiles and constant inlet velocities.

Results show that mixing in the domain is typically increased by topographic variation, where isolated expansions saw an increase in mixing, but the associated velocity decrease in expansions had contrasting effects on mixing. Likewise, a contraction with an increased velocity caused more mixing, seeing geometry change and velocity acting as compounding factors. 2D results including along channel topographic variation modelled after Hood Canal's …

Open-Source And 3-D Printed Autoinjector, Anjutha Selvaraj

Undergraduate Student Research Internships Conference

Autoinjectors have become popular modern injectable medical devices used as drug delivery systems. Due to its ease, capability and reliability compared to other conventional injectable medical devices, the market and manufacturing demand for autoinjector devices are increasing at a staggering rate. Although autoinjectors can offset healthcare treatment costs through self-administered medication, they are expensive for consumers. This paper describes the design and manufacture of a spring-driven and 3-D printed autoinjector using open-source hardware. By making it an open-source resource for everyone, the barrier of advanced research in design and production can be lifted, thus making it easily manufacturable and cost-effective. …

Examination Of Installation Effects On Multi-Jet Meter Performance, Domenic Quiquero

Undergraduate Student Research Internships Conference

Alongside Mitchell Boody and Dr. Eric Savoury's supervision, the effect of additional internal friction of multi-jet flow meters caused by various orientations was experimentally analyzed. Multi-jet flow meters are commonly used in multi-unit residential buildings, thus by understanding the effects of the corresponding orientational loss, our industry partners can better assess water cost. This study coincides with Mitchell Boody's work using simulations to demonstrate the impact of frictional loss in multi-jet flow meters and building upon the work of Paulo Barros Rodrigues with other orientations.

Normative Joint Angles And Compensation During Fit-Hansa Test, Jennifer J. Villeneuve

Undergraduate Student Research Internships Conference

Imagine a world where no injuries occurred, muscular compensation was able to be detected early on and imbalances resolved before any risks appear. Muscular compensation can cause injuries, especially with repetitive motion or through activities of daily living. The study I conducted focuses on the compensation methods of shoulder abduction and trunk lean during the FIT-HaNSA series. Determining the normative ranges of motion can increase early detection of fatigue for all individuals. This can help make repetitive jobs such as working in a factory much safer for all employees, as they can switch tasks as soon as fatigue is identified. …

A Qualitative Look Into Repair Practices, Jumana Labib

Undergraduate Student Research Internships Conference

This research poster is based on a working research paper which moves beyond the traditional scope of repair and examines the Right to Repair movement from a smaller, more personal lens by detailing the 6 categorical impediments as dubbed by Dr. Alissa Centivany (design, law, economic/business strategy, material asymmetry, informational asymmetry, and social impediments) have continuously inhibited repair and affected repair practices, which has consequently had larger implications (environmental, economic, social, etc.) on ourselves, our objects, and our world. The poster builds upon my research from last year (see "The Right to Repair: (Re)building a better future"), this time pulling …

Video-Based Non-Contact Vibration Measurement Software, Mithila Sothynathan, Samuel Asokanthan

Undergraduate Student Research Internships Conference

This study aims to develop a cost-effective, accessible, and contactless means of measuring vibrations.

Mathematical Analysis Of A Hemispherical Resonator Gyroscope, Sean Mcevoy

Undergraduate Student Research Internships Conference

A Hemispherical Resonator Gyroscope (HRG) is a gyroscope that uses vibrations to measure the orientation of a device based on the Coriolis effect. A mathematical model was confirmed so that a mathematical simulation could be made and used for a simulation of the HRG in operation.

Comparison Of Layered Nickel Cobalt Manganese Oxide Cathodes With Different Compositions And Morphologies In Lithium-Ion Batteries, Fanny Poon

Electronic Thesis and Dissertation Repository

The revolutionary rechargeable lithium-ion battery paves the way for environmentally-friendly applications such as electric vehicles. Nevertheless, further improvements are required to match or exceed the performance of conventional internal combustion engine vehicles, such as higher energy density, faster charging speed, longer lifetime, better safety and lower cost. Lithium layered nickel cobalt manganese oxides (NCM) are a popular choice of cathode material, but they still suffer from problems such as cation mixing, volume changes, microcracking, surface side reactions, high temperature performance issues and structural reconstruction. This thesis compares various NCM materials to figure out what guidelines should be followed to improve …

Motion And Crosslinked Polyethylene Wear In Reverse Total Shoulder Arthroplasty, Christopher Millward

Electronic Thesis and Dissertation Repository

The reverse total shoulder arthroplasty (RTSA) has quickly grown to become the most commonly used shoulder arthroplasty design; however, reports have shown evidence of RTSA failures related to polyethylene wear and damage. Therefore, the present work investigated the wear of crosslinked polyethylene (XLPE) in environments similar to that of an in vivo RTSA. Additionally, a computational model was developed based on a previous study of the shoulder motions obtained from a selection of typical patients with RTSA. This model quantified the amount of glenohumeral motion that an RTSA may be subjected to in vivo and provided an approximate value for …

To Develop A Clinically Friendly Multi-Segment Kinematic And Kinetic Foot Model And Test It On Pre-/Post-Hto Patients With Medial Knee Osteoarthritis And Knee Varus, Songlin Zhu

Electronic Thesis and Dissertation Repository

This study aims to develop a clinically useful multi-segment foot model that will enable the analysis of foot kinematics and kinetics in an optical motion capture laboratory setting. This study will also test the new multi-segment foot model on patients with knee osteoarthritis and varus knee alignment that is corrected by high tibial osteotomy (HTO). The multi-segment foot model divides the foot into four functional segments: the hindfoot, midfoot, forefoot and hallux. An X-Z-Y-Cardan angle rotation convention was used to determine intersegmental dorsi/plantar flexion, inversion/eversion, and internal/external rotation. Joint moments, joint powers and medio-longitudinal arch (MLA) height/length ratio were also …

Computational Modelling Of Resin Infiltration And Curing In High Pressure Resin Transfer Molding, Anthony Paul Rexford Sherratt

Electronic Thesis and Dissertation Repository

Increased pressure on automotive manufactures to reduce overall greenhouse gas emissions from their vehicles has driven research into replacing conventional steel components with carbon fiber reinforced plastics (CFRP). This is due to their high weight specific properties and design freedom. High pressure resin transfer molding (HP-RTM), a derivative of resin transfer molding, is a manufacturing process for CFRP’s that offers high automation potential and low cycle times; critical properties of a manufacturing process for the automotive sector.

The goal of the present work is to increase the accuracy and reduce the computational overhead of current RTM infiltration and curing models. …

Cooling Systems Analysis For Plastic Mold Injection Tools, Veronica Flores Quijada

Electronic Thesis and Dissertation Repository

The Plastic Injection Mold (PIM) industry has been searching for new technologies that improve the manufacturing of parts by reducing the production time and cost as well as increasing the quality of the product. The cooling systems in the PIM are designed initially to be straight-drilled into the mold, but this manufacturing process has traditionally not been very effective, since for molded parts with complex geometries, the cooling channels are not able to reach certain areas. This limitation has led the industry to develop conformal cooling channels that use the additive manufacturing technology, which allows the cooling channels to conform …

The Effects Of A Porous Internal Lattice Design On The Articular Contact Mechanics Of Radial Head Hemiarthroplasty Implants, Jessica Benitah

Electronic Thesis and Dissertation Repository

Hemiarthroplasty, where one side of a joint is replaced, is a minimally invasive procedure. It allows for the preservation of native tissue, though a significant ramification is accelerated cartilage wear when articulating with high stiffness materials that do not mimic the mechanical stiffness of the native tissue. An implant that employs a lattice design can significantly lower the stiffness of a solid structure whilst maintaining strength. This study was conducted to investigate the effect of implementing a porous internal lattice structure with a thin outer shell on the articular contact mechanics, using a radial head hemiarthroplasty. It was hypothesized that …

The Role Of Transient Vibration Of The Skull On Concussion, Rodrigo Dalvit Carvalho Da Silva

Electronic Thesis and Dissertation Repository

Concussion is a traumatic brain injury usually caused by a direct or indirect blow to the head that affects brain function. The maximum mechanical impedance of the brain tissue occurs at 450±50 Hz and may be affected by the skull resonant frequencies. After an impact to the head, vibration resonance of the skull damages the underlying cortex. The skull deforms and vibrates, like a bell for 3 to 5 milliseconds, bruising the cortex. Furthermore, the deceleration forces the frontal and temporal cortex against the skull, eliminating a layer of cerebrospinal fluid. When the skull vibrates, the force spreads directly to …

Mass Advection–Diffusion In Creeping Flow Through An Orifice Plate: A Model For Nanoporous Atomically Thin Membranes, Harpreet Atwal, Anika Wong, Michael Boutilier

Chemical and Biochemical Engineering Publications

Continuum transport equations are commonly applied to nanopores in atomically thin membranes for simple modeling. Although these equations do not apply for nanopores approaching the fluid or solute molecule size, they can be reasonably accurate for larger nanopores. Relatively large graphene nanopores have applications in small particle filtration and appear as unwanted defects in large-area membranes. Solute transport rates through these nanopores determine the rejection performance of the membrane. Atomically thin membranes commonly operate in a regime where advection and diffusion both contribute appreciably to transport. Solute mass transfer rates through larger nanopores have previously been modeled by adding continuum …

The Influence Of Frontal And Axial Plane Deformities On Contact Mechanics During Squatting: A Finite Element Study, Yidan Xu

Electronic Thesis and Dissertation Repository

Knee Osteoarthritis (KOA) is a degenerative joint disease and a leading cause of disability worldwide. Lower limb malalignment was a risky factor leading to KOA, altering the load distributions. This study aimed to study the influence of knee deformities on knee contact mechanics and knee kinematics during squatting. A full-leg squat FE model was developed based on general open-source models and validated with in vivo studies to investigate the outputs under frontal malalignment (valgus 8° to varus 8°) and axial malalignment (miserable malalignment 30°). As a result, Varus-aligned and miserable aligned models increased medial tibiofemoral force and lateral patellar contact …

An Investigation Of Porous Materials For The Capture Of Concentrated Solar Energy, Elizabeth Blokker

Electronic Thesis and Dissertation Repository

Fossil fuel usage is resulting in climate change. There is a need to switch to renewable energies, but existing technologies lack the efficiency for wide-scale adoption. Concentrating solar energy to a receiver using a parabolic reflector is an efficient method of converting sunlight into thermal energy at a high efficiency. Current receivers suffer efficiency challenges due to significant re-radiation losses as they reach a high temperature at the front surface. This project is focused on the creation of a computational model to simulate the radiation heat transfer in porous geometries, which can be used to optimize the geometric properties of …