Mechanical Engineering Commons^™

The Analysis Of Mechanical Exfoliation Of Graphene For Various Fabrication And Automation Techniques, Lance Yarbrough

Mechanical Engineering Undergraduate Honors Theses

Mechanical Exfoliation of Graphene is an often-overlooked portion of the fabrication of quantum devices, and to create more devices quickly, optimizing this process to generate better flakes is critical. In addition, it would be valuable to simulate test pulls quickly, to gain insight on flake quality of various materials and exfoliation conditions. Physical pulls of graphene at various temperatures, pull forces, and pull repetitions were analyzed and compared to the results of ANSYS simulations, solved for similar results. Using ANSYS’ ability to predict trends in exfoliations, flake thickness and coverage using stress and deflection analyses were investigated. Generally, both strongly …

Large Eddy Simulation Of Fluid Mixing In Migadome Facility For The Astfe Nuclear Thermal Hydraulics Cfd Competition, Kolten Strauss

Mechanical Engineering Undergraduate Honors Theses

This paper is a documentation of a submission to the First Annual ASTFE Nuclear Thermal Hydraulics Computational Fluid Dynamics (CFD) Competition [1]. To validate simulations of turbulent mixing in buoyancy-driven flows, an air and argon test case was set up inside the University of Michigan’s MiGaDome mixing vessel. This submission to the competition used a polyhedral mesh of about two and a half hundred thousand cells, a Large Eddy Simulation (LES) of the MiGaDome, and the Wall-Adapting Local Eddy-viscosity (WALE) subgrid approximation model. The competition included a factor considering the energy cost of our simulations, so it was decided to …

Flow Characterization With Acoustic Emission Sensing, Jackson Marsh

Mechanical Engineering Undergraduate Honors Theses

Acoustic emissions (AE) allow for non-intrusive sensing into many types of systems. In systems where there is flow of some type, AE is very useful as these types of systems can be characterized in many ways from the collisions or creation of the flow. Correctly setting up the AE system is extremely important. Failure to do so results in imprecision and inaccurate data being collected. Because of this synchronization techniques, sensor configurations, and data acquisition systems must all align. This can be done with off-the-shelf, commercial systems, but this does not allow for customization and the ability to tailor the …

Model-Based Comparison Of Biological Organism And Electro-Mechanical System Resiliency Strategies, Nicholas Ratycz

Mechanical Engineering Undergraduate Honors Theses

Bio-inspired design has been used by many engineers to solve difficult problems or to make manufacturing processes more efficient. Biomimetics is the study of implementing the structure or function of biological substances, materials, mechanisms, and processes onto artificial ones that mimic the original. The goal of the BIASD tool is to provide bio-inspiration for engineers by studying the fault-adaptive strategies that biological systems use, rather than just their structure or function. In this thesis, the fault adaptive strategies of both a biological example and that of a real cubesat are compared using three types of model-based system diagrams to show …

Cam And Design For Manufacturing: Developing A Project-Based Learning Course, Stephen Pierson

Mechanical Engineering Undergraduate Honors Theses

To effectively serve student career success, mechanical engineering programs must teach students how to account for manufacturing considerations in design. Despite this, manufacturing education is a glaring area of need in current engineering curricula. In fact, basic manufacturing knowledge is one of the only hard skills consistently ranked as one of the greatest weaknesses of mechanical engineering hires in surveys of industrial employers over the last few decades. Without radically changing departmental curriculum to include more emphasis on design-build projects, one solution to combat this is to incubate a lab course in mechanical engineering programs in which undergraduates would practice …

Experimental And Numerical Investigation Of Air-Cooled Heat Sinks, Ethan Weems

Mechanical Engineering Undergraduate Honors Theses

Lightweight and affordable cooling capabilities are critical as the physical scale of electronics continues to decrease. Air-cooled heat sinks that dissipate heat from electronic components to the surrounding air are excellent candidates to fill this role. While plate-fin and pin-fin heat sinks have been implemented extensively for electronic cooling, recent advances in additive manufacturing enable the fabrication of more complex structures. In this undergraduate Honors thesis, a means by which to generate novel heat sink geometries is presented. To that end, an experimental characterization facility is developed to evaluate existing traditional heat sinks. The heat transfer performance of the heat …

Comparative Analysis Of Command Protocols For Cubesat Data Handling Systems, Roman Dowling

Mechanical Engineering Undergraduate Honors Theses

Researchers at the University of Arkansas developed ARKSAT-1, a cubic satellite with the purpose of employing an LED with a tracking system to perform spectroscopic measurements of the atmosphere.

The control board of the satellite contained several microcontrollers which worked in concert to collect and manage data. Discussed in this report are the software programs developed for the microcontrollers, dual Arduino MKRZeros, utilized as data repositories and for control of satellite peripherals. The programs discussed in this project include an original existing command-response protocol and an improved batch-command protocol, each with its accompanying data handling and storage system. These programs …

Thermal Resistance Characterization Of High-Voltage Sic Power Module, Landon Lemmons

Mechanical Engineering Undergraduate Honors Theses

Researchers within the University of Arkansas Electrical Engineering Research Department have embarked on a project aimed at enhancing the thermal performance of high-voltage power modules. To aid in the progress of this project, the design, and development of a thermal tester device are needed. The primary objective of this device is to determine the various thermal properties of high-voltage power modules that the electrical engineering department has developed. Additionally, the project aims to facilitate electrical loading tests on power modules and provide researchers with the means to calibrate the power module in terms of thermal load. This project also possesses …

Reynolds-Averaged Navier-Stokes Cfd Simulation Of High-Speed Boundary Layers, Michael Tullis

Mechanical Engineering Undergraduate Honors Theses

This paper presents an investigation of Reynolds-averaged Navier-Stokes (RANS) turbulence models used in computational fluid dynamics (CFD) simulations of boundary layer flow and heat transfer in high Mach number flows. This study evaluates an industry standard RANS turbulence model (k-omega SST) and a recently proposed modification to that model (Danis and Durbin [1]), and quantifies the accuracy for predicting high Mach number boundary layer flow. The test cases were previously documented by Duan et al. (2018), who used direct numerical simulation (DNS) to calculate boundary layer flow of an ideal gas over a flat plate at freestream Mach numbers ranging …

Investigation Of Dynamic Hybrid Rans-Les Turbulence Modeling For Cfd Simulation Of A Normal Jet In Crossflow, Cole Simmonds

Mechanical Engineering Undergraduate Honors Theses

The jet in crossflow is a canonical flow feature in many natural and engineered systems, ranging from pollutant dispersal in exhaust discharge to film cooling of high-temperature components in modern propulsion systems. The ability to computationally predict the flow features of jets in crossflow accurately and efficiently is therefore important for analysis and design for a wide variety of applications. In this study the capabilities of the dynamic hybrid RANS-LES (DHRL) turbulence modeling technique are investigated and compared to an industry standard Reynolds-averaged Navier-Stokes model (k-omega SST) in order to quantify the accuracy and computational cost of the two approaches. …

Characterization And Manipulation Of Double-Stranded Dna Using Atomic Force Microscopy, Lauren Skartvedt

Mechanical Engineering Undergraduate Honors Theses

An atomic force microscope (AFM) is used to scan high-resolution images on the nano scale. The lambda DNA used for this project are 48,502 base pairs in length and are double-stranded. This project utilizes the NanoSurf Core AFM in order to characterize and manipulate strands of lambda DNA which have been deposited on a mica surface. The deposition process of the DNA on the mica surface was developed by the National Institute of Standards and Technology and the University of Colorado - Boulder. The AFM is used in imaging mode to scan the mica surface to locate the DNA. When …

A Systematic Study Into The Design And Utilization Of Burn Wire As A Means Of Tensioning And Releasing Spacecraft Mechanisms Through Applied Joule Heating, Chandler Dye

Mechanical Engineering Undergraduate Honors Theses

The joule heating characteristics of Nichrome burn wires, often used as a thermal cutting device in mechanisms designed to fasten and release CubeSat deployables, are examined in the following thesis. Wires ranging from 0.125 inches to 2 inches long, and diameters of 30 Ga and 40 Ga, are investigated through analytical calculations and thermal simulations based on heat transfer due to joule heating, and through physical circuitry-based experiments. The temperature data is used to generate heating curves to predict the time it takes for Nichrome wires to fail under varying testing parameters. This research aims to catalog a series of …

Enhancing Stability Of High-Nickel Cathodes For Lithium-Ion Batteries Through Additive Manufacturing Of Cathode Structure, Matthew Sullivan

Mechanical Engineering Undergraduate Honors Theses

Lithium-ion batteries (LIBs) are currently the best method to store electrical energy for use in portable electronics and electronic vehicles. New cathode materials for LIBs are consistently studied and researched, but few are as promising and attainable as nickel-rich transition metal oxides such as LiNi1-x-yMnxCoyO2 (NMC). NMC materials exist with many different mass ratios, but higher nickel content materials provide higher energy density. With this increase in capacity comes a sacrifice with cyclability, as high-nickel NMC variants are prone to structure collapse, transition metal dissolution, and cracks due to volume change. In this report, mechanical modification of the electrode by …

Generative Designs Of Lightweight Air-Cooled Heat Exchangers, Connor Miller

Mechanical Engineering Undergraduate Honors Theses

The development of high-performance air-cooled heat exchangers is required to permit the rapid growth of vehicle and aircraft electrification. In electric vehicles and airliners, the motors and power electronics are integrated into a compact space, leading to unprecedently high power density. To achieve higher overall thermal efficiency, the heat exchangers must be extremely light while maintaining their heat transfer performance and mechanical robustness. Recently advances in 3D metal printing, e.g., direct metal laser sintering, and selective laser melting, have enabled the manufacturing of high-performance robust heat exchangers by eliminating thermal boundary resistance and ensuring a uniform thermal expansion coefficient. Nonetheless, …

Autonomous Material Refill For Swarm 3d Printing, William C. Jones

Mechanical Engineering Undergraduate Honors Theses

3D printing currently offers robust and cheap rapid prototyping solutions. While standard 3D printing remains at the periphery of mass production, the technology serves as a starting point for the development of swarm manufacturing. Since swarm manufacturing is predicated upon autonomy, swarm technology companies such as AMBOTS are seeking to minimize human involvement in the swarm’s functions. At present, the 3D printing swarm consists of the printers, a transporter which can take them between job sites, and the floor tiles which provide power and support the build surfaces. To add to this ecosystem, this project is focused on the design …

Atomic Force Microscopy Based Dna Sensing And Manipulation, Matthew Shubert

Mechanical Engineering Undergraduate Honors Theses

Sequencing DNA provides a positive impact for the biomedical community by understanding a wide variety of applications such as human genetics, disease, and pathogens. The reason the Arkansas Micro & Nano Systems lab is involved with research in DNA sequencing is due to the current, leading industry method. Nanopore sequencing was developed by Oxford Nanopore Technology in which its sequencing method separates double stranded DNA to electrically characterize individual nucleotides traveling through a charged nanopore. Unfortunately, nanopore sequencing uses biological materials that require a shelf life and drives high cost. Therefore, the Arkansas Micro & Nano Systems lab has developed …

Mathematical Modeling Of A Two Wheeled Robotic Base, Kathryn Remell

Mechanical Engineering Undergraduate Honors Theses

This thesis presents the concept of using a two wheeled robot on the moon and briefly explores the requirements for successful long term operation in a lunar environment. The mathematical model for the motion of a robot with two fixed wheels on a differential drive with in a global reference frame. The robot is assumed to be balancing a platform so the mathematical model to balance the platform with wheel motors is also developed and briefly evaluated.

Nanoscratch Study Of Diamond-Like Carbon Coatings With A Polydopamine + Sio2 Adhesive Underlayer, Anna Fisher

Mechanical Engineering Undergraduate Honors Theses

Diamond-like carbon (DLC) coatings have a wide array of desirable characteristics such as low friction, high hardness, and scratch resistance. Due to high residual stress and thermal mismatch, DLC films experience adhesion difficulties when bonded with metallic substrates, leading to cracking and delamination. In this study, the properties of a new coating with a polydopamine underlayer and silica nanoparticles bonded to a stainless-steel substrate (PDA+SiO2/DLC) were studied alongside three other samples, one with a polydopamine underlayer (PDA/DLC), one with a trimethylsilane (TMS) underlayer (TMS/DLC), and one with no underlayer (DLC only). Nanoscratch tests were performed with a 1 μm spheroconical …

Transient Performance And Melt Front Characterization Of Phase Change Materials, Tyler Stamps

Mechanical Engineering Undergraduate Honors Theses

Thermal management systems are often over-designed for average use in order to handle spikes in heat generation, which increases the spatial and financial requirements. One way to mitigate this is via the use of phase change materials (PCMs) as thermal buffers and storage media. This material type exhibits excellent latent heat at the sacrifice of conductivity. The present paper examines the melt front behavior of a common solid to liquid PCM, paraffin, experimentally and numerically. The experimental scenario was a block of PCM with a constant temperature heat flux introduced on one end and a constant temperature cold boundary condition …

Improving The Performance Of An Ead Aircraft By Use Of A Retractable Electrode System, Michael Alexander Fredricks

Mechanical Engineering Undergraduate Honors Theses

Electroaerodynamic (EAD) propulsion is a growing area of research for small, low powered aircraft. Recent tests of EAD aircraft have demonstrated low performance in unpowered, gliding flight. The purpose of this paper is to investigate the effect of a retractable electrode system on the flight performance of an EAD aircraft. An analysis of electrode drag contribution on the MIT ionic wind plane’s performance predicts a maximum lift to drag ratio of 22, with the addition of a retractable electrode system, for a similarly sized and modeled EAD aircraft. An experiment is developed using a prototype aircraft, launcher, and retraction system …

Algorithm Development Of Topology Optimization For Pcm Based Heat Sinks, Diego L. De Los Reyes

Mechanical Engineering Undergraduate Honors Theses

With the inherent usage of the computer when dealing with additive manufacturing, it only makes sense to use that higher computing power through simulation and iterative design to use the mathematical concept of topology and optimize the kind of geometry and shapes to be produced for a certain application, especially thermal ones since most 3D printing applications focus on purely the mechanical. To determine what the shape will be, an objective function of how much heat can be dispersed from a hypothetical heat source, assumed to be a type of electronic device, is maximized while being constrained by other variables, …

Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins

Mechanical Engineering Undergraduate Honors Theses

According to the CDC, atrial fibrillation is responsible for more than 454,000 hospitalizations and approximately 158,000 deaths per year. A common treatment for atrial fibrillation is catheter ablation, a process in which a long flexible tube is guided through the femoral artery and to the source of arrhythmia in the heart, where it measures the electrical potential at various locations and converts problematic heart tissue to scar tissue via ablation. This paper details the design and control of a low-cost ($400) peristaltic pump system using repetitive control to replicate blood pressure in the left atrium in a conductive silicone model …

Thermal Testing And Characterization Of Nanoparticles Synthesized For Biological Treatment, Tonie Butler

Mechanical Engineering Undergraduate Honors Theses

The overall goal of this research project is to synthesize iron core, silica capped nanoparticles that, when they are exposed to a particular magnetic field, will react by increasing in temperature and emitting substantial thermal output. They will be injected into the human body for biological benefit by targeted thermal radiation. Once in the human body, ideally, they will be able to target a specific area, and then a magnetic field will be applied to induce thermal output through the process of hyperthermia. As the nanoparticles emit heat, they will mimic the natural bodily behavior seen by way of hyperthermia, …

Designing Cryogenic Strain Device For 2d Materials, Jake Carter

Mechanical Engineering Undergraduate Honors Theses

The Churchill lab working within the Physics Department at the University of Arkansas is working to create important quantum states including weak topological insulators (TIs) through the use of symmetry engineering and topological electronic states in two-dimensional (2D) crystals of WHM materials. Experimental results of these topological states have been obstructed due to the difficulty to perform controlled in situ strain. This project strives to create a mount to utilize a piezoelectric nanopositioner within cryostats achieving an in situ strain that creates the quantum states the lab is looking to observe. This report also examines the necessary equations to determine …

Characterizing High Entropy Alloys For Hypersonic Applications, Katherine Pettus

Mechanical Engineering Undergraduate Honors Theses

In this paper, the properties of a new and broad class of materials, high entropy alloys (HEAs), were investigated and evaluated for hypersonic applications. The plan was to identify candidate hypersonic HEAs and model the high-temperature strength using new advanced material models that account for asymmetry and anisotropy characterized with available test data. After accessing a local database of HEAs and their material properties in collaboration with Dr. Gorsse et al., it was realized the knowledge of HEAs is currently very broad but lacks depth. While hundreds of HEAs have been created and tested, none so far have both sufficient …

Noise Control In Sorting Conveyors, Eyra Herrera

Mechanical Engineering Undergraduate Honors Theses

E-commerce has increased the necessity of effective material handling equipment in warehouses and distribution centers. Sorter conveyors systems facilitate material handling by providing a reliable and automated system to classify and distribute products in a gentle and rapid manner. With the steady increase of speed in sorter conveyors to satisfy today’s industry demand, some systems have started to produce high noise levels that could potentially affect workers’ health. Since decreasing the speed of these conveyors is not a viable option to decrease noise in sorter equipment, industries have opted to find other ways to apply noise control to their equipment. …

Attitude Determination And Control Of Arksat-1, Jared Gilliam

Mechanical Engineering Undergraduate Honors Theses

ARKSAT-1 is a nanosatellite developed at the University of Arkansas as part of NASA’s CubeSat Launch Initiative (CSLI). The goal of ARKSAT-1 is to utilize an LED emitter paired with a ground-based tracking system to perform measurements of the composition of the atmosphere using spectroscopy. As part of its function, it is imperative that the satellite is able to control its orientation so that the emitter is aligned as closely as possible with the ground tracker. To do this, the attitude control system of ARKSAT-1 uses magnetic actuators to create a torque on the satellite by interacting with Earth’s magnetic …

A History And Status Of Wind Energy Potential In Arkansas, Pre And Post Covid-19, Will Blasingame

Mechanical Engineering Undergraduate Honors Theses

Historically, wind-generated electricity has been the largest renewable energy sources in the United States. Wind-rich regions like Oklahoma and Texas have fueled growth and sold that electricity to electric utilities located in wind-poor states like Arkansas in the form of Power Purchase Agreements. Future technologies such as Vertical Axis Wind Turbines, small wind turbines, and Tesla turbines designed to generate electricity from wind show promise in unlocking more expensive wind resources in regions like Northwest Arkansas by mitigating concerns about low wind speeds and noise. However, more factors than just feasibility influence the growth of wind power. Governmental policies such …

Construction Of A Hyperspectral Imager Using 3d-Printed And Off-The-Shelf Components, Joshua Moorhouse

Mechanical Engineering Undergraduate Honors Theses

The Arkansas Center for Space and Planetary Sciences is working in collaboration with the Mechanical Engineering department to create a relatively cheap and modifiable hyperspectral imager. It is constructed using 3D-printed and off-the-shelf components from Edmund Optics and Amazon. The iteration created in this paper delivers spectrograms in the visible spectrum. The long-term goals of the camera are to create hyperspectral images from these spectrograms and to advance the imager into the infrared and near-infrared spectra. This imager is being developed to be used in the Arkansas Center for Space and Planetary Sciences environmental test chambers to further the scientific …

Enhancement Of Phase Change Material Sorbitol By Nanoparticle Inclusion For Improving Thermal Energy Storage Capabilities, Joshua Kasitz

Mechanical Engineering Undergraduate Honors Theses

Thermal management of electronic devices has become an increasingly vital field of study with the rapid miniaturization of many key electrical components. With the significant improvement of semiconductor manufacturing and intensified focus on interconnects, electronic devices have decreased in size at an incredible rate. Decreasing spatial requirements is essential to improving device capabilities as the electronic system is able to incorporate more components. Currently, electronic systems are drastically limited by the capabilities of their cooling mechanisms. Smaller devices lead to large increases in the energy density of the system and require more powerful cooling systems to maintain proper component operating …