Mechanical Engineering Commons^™

Development Of A Data Acquisition System For Unmanned Aerial Vehicle (Uav) System Identification, Donald Joseph Lear

Mechanical & Aerospace Engineering Theses & Dissertations

Aircraft system identification techniques are developed for fixed wing Unmanned Aerial Vehicles (UAV). The use of a designed flight experiment with measured system inputs/outputs can be used to derive aircraft stability derivatives. This project set out to develop a methodology to support an experiment to model pitch damping in the longitudinal short-period mode of a UAV. A Central Composite Response Surface Design was formed using angle of attack and power levels as factors to test for the pitching moment coefficient response induced by a multistep pitching maneuver.

Selecting a high-quality data acquisition platform was critical to the success of the …

Computational Methods For Nonlinear Systems Analysis With Applications In Mathematics And Engineering, Geoffrey Kenneth Rose

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation into current methods and new approaches for solving systems of nonlinear equations was performed. Nontraditional methods for implementing arc-length type solvers were developed in search of a more robust capability for solving general systems of nonlinear algebraic equations. Processes for construction of parameterized curves representing the many possible solutions to systems of equations versus finding single or point solutions were established. A procedure based on these methods was then developed to identify static equilibrium states for solutions to multi-body-dynamic systems. This methodology provided for a pictorial of the overall solution to a given system, which demonstrated the possibility …

Development Of The Compact Jet Engine Simulator From Concept To Useful Test Rig, Henry H. Haskin

Mechanical & Aerospace Engineering Theses & Dissertations

NASA had a goal to develop a set of modeling tools for designing next generation civil transport aircraft with reduced noise, emissions and increased fuel efficiency by 2016. To verify the models, a database of aerodynamic and acoustic data was needed for an unconventional flying wing design that was predicted to meet the goals. A Compact Jet Engine Simulator (CJES) was needed as the jet source for the 5.8% scale model. Ultra-Compact Combustor Technology from the Air Force Research Laboratory was used to reduce the conventional burner acoustic test rigs down to the required scale size. The Air Force design …

Investigation, Modeling And Validation Of Digital Bridge For A New Generation Hot-Wire Anemometer, Karthik Kamalakar Joshi

Mechanical & Aerospace Engineering Theses & Dissertations

The Digital Bridge Thermal Anemometer (DBTA) is a new generation anemometer that uses advanced electronics and a modified half-Wheatstone bridge configuration, specifically a sensor and a shunt resistor in series. This allows the miniaturization of the anemometer and the communication between host computer and anemometer is carried out using serial or ethernet which eliminates the noise due to the use of long cables in conventional anemometer and the digital data sent to host computer is immune to electrical noise. In the new configuration the potential drop across a shunt resistor is used to control the bridge.

This thesis is confined …

A Low Cost Inflatable Cubesat Drag Brake Utilizing Sublimation, Adam Charles Horn

Mechanical & Aerospace Engineering Theses & Dissertations

The United Nations Inter-Agency Debris Coordination Committee has adopted a 25-year post-mission lifetime requirement for any satellite orbiting below 2000 km in order to mitigate the growing orbital debris threat. Low-cost CubeSats have become important satellite platforms with startling capabilities, but this guideline restricts them to altitudes below 600 km because they remain in orbit too long. In order to enable CubeSat deployments at higher release altitudes, a low-cost, ultra-reliable deorbit device is needed.

This thesis reports on efforts to develop a deployable and passively inflatable drag brake that can deorbit from higher orbital altitudes, thereby complying with the 25-year …

Development Of An Analysis And Design Optimization Framework For Marine Propellers, Ashish C. Tamhane

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, a framework for the analysis and design optimization of ship propellers is developed. This framework can be utilized as an efficient synthesis tool in order to determine the main geometric characteristics of the propeller but also to provide the designer with the capability to optimize the shape of the blade sections based on their specific criteria.

A hybrid lifting-line method with lifting-surface corrections to account for the three-dimensional flow effects has been developed. The prediction of the correction factors is achieved using Artificial Neural Networks and Support Vector Regression. This approach results in increased approximation accuracy compared …