Mechanical Engineering Commons^™

Experimental And Theoretical Investigation Of Mechanical Response Of Laser-Sintered Diamond Lattice Structures, Clayton Neff, Neil Hopkinson, Nathan B. Crane

Faculty Publications

Typically additive manufacturing (AM) processes are limited to a single material per part while many products benefit from the integration of multiple materials with varied properties. To achieve the benefits of multiple materials, the geometric freedom of AM could be used to build internal structures that emulate a range of different material properties such as stiffness, Poisson’s ratio, and elastic limit using only one build material. This paper examines the range of properties that can be simulated using diamond lattice structures manufactured from Nylon 12 with a commercial laser sintering process. Diamond lattices were fabricated with a unit cell length …

Impact Of Extended Sintering Times On Mechanical Properties In Pa-12 Parts Produced By Powderbed Fusion Processes, Garrett Craft, Justin Nussbaum, Nathan B. Crane, J. P. Harmon

Faculty Publications

Additive Manufacturing provides many advantages in reduced lead times and increased geometric freedom compared to traditional manufacturing methods, but material properties are often reduced. This paper considers powder bed fusion of polyamide 12 (PA12, Nylon 12) produced by three different processes: laser sintering (LS), multijet fusion (MJF)/high speed sintering (HSS), and large area projection sintering (LAPS). While all utilize similar PA12 materials, they are found to differ significantly in mechanical properties especially in elongation to break. The slower heating methods (MJF/HSS and LAPS) produce large elongation at break with the LAPS process showing 10x elongation and MJF/HSS exhibiting 2.5x the …

Design For Maintainability In Developing Communities—A Case Study On The Uros Islands, Thomas Barlow

Undergraduate Honors Theses

Designing products for developing communities has exposed many of the underlying assumptions that engineers from developed nations have during the design process. There has been much written about these underlying assumptions in order to create a better framework for designing for developing communities. One unexplored, yet important area is the universality of common maintainability principles used in developed countries when designing products used in developing communities. Such principles include: simplicity, diagnosability, standardization of parts, modular subassemblies, minimizing assembly and disassembly parts, labeling components, increased life of moving parts, manuals, and simplifying tools needed for repairs [1]–[3]. The purpose of this …

Evaluation Of Processing Variables In Polymer Projection Sintering, Justin Nussbaum, Nathan B. Crane

Faculty Publications

Purpose – Projection sintering, a system for selectively sintering large areas of polymer powder simultaneously with a high power projector is introduced. The paper evaluates the suitability of laser sintering process parameters for projection sintering as it uses substantially lower intensities, longer exposure times, and larger areas than conventional laser sintering (LS).

Design/methodology/approach – The tradeoffs in sintering outcomes are evaluated by creating single layer components with varied exposure times and optical intensities. Some of these components were cross-sectioned and evaluated for degree of densification while the single layer thickness and the maximum tensile force was measured for the rest. …

Controlling Normal Stiffness In Droplet-Based Linear Bearings, Qi Ni, Nathan B. Crane

Faculty Publications

While Capillary forces are negligible relative to gravity at the macroscale, they provide adequate force to effectively manipulate millimeter to micro meter objects. The fluidic actuation can be accomplished using droplets that also act as bearings. While rotary droplet bearings have been previously demonstrated, this paper considers the performance potential of discrete droplets acting as linear bearings. Specifically, it addresses the positioning accuracy of a droplet-based bearing consisting of a droplet between a moving plate and a stationary substrate with constrained wetting region under a normal load using both closed form analytical solutions and numerical simulations. The vertical force and …

Impact Of Vapor Polishing On Surface Quality And Mechanical Properties Of Extruded Abs, Clayton Neff, Matthew Trapuzzano, Nathan B. Crane

Faculty Publications

Purpose — Additive manufacturing (AM) is readily capable of producing models and prototypes of complex geometry and is advancing in creating functional parts. However, AM processes typically underperform traditional manufacturing methods in mechanical properties, surface roughness, and hermeticity. Solvent vapor treatments (vapor polishing) are commonly used to improve surface quality in thermoplastic parts, but the results are poorly characterized.

Design/methodology/approach — This work quantifies the surface roughness change and also evaluates the effect on hermeticity and mechanical property impacts for “as-printed” and acetone vapor-polished ABS tensile specimens of 1, 2, and 4 mm thicknesses produced by material extrusion (FDM).

Findings …