Mechanical Engineering Commons^™

Predictive Thermal Modeling And Characterization Of Ultrasonic Consolidation Process For Thermoplastic Composites, Madeline Kirby

LSU Master's Theses

Ultrasonic consolidation (USC) of thermoplastic composites (TPCs) is a highly attractive and promising method to manufacture high-performance composites. This work focuses on USC of dry carbon fiber (CF) fabrics with high-temperature polyphenylene sulfide (PPS) films. Experimental trials to assess feasibility of the process are time-consuming. Consequently, a predictive thermal model would facilitate process parameters selection to reduce expensive trial-and-error approaches. This paper presents a 2D finite element model of samples under consolidation, incorporating equations for viscoelastic heating, matrix phase change, and material properties. Theoretical temperature profiles for nodes of interest were compared to the corresponding experimental temperature curves for various …

Characterization Of Friction Element Welding Using Finite Element Modeling, Ankit Varma

All Dissertations

Friction element welding (FEW) has been advocated as a solution to weld different materials together, with the ability to join high-strength materials for a range of thicknesses with low input energy and a short processing time. This work develops a coupled thermal-mechanical finite element model to better understand the physical mechanisms involved in the process and to predict temperature and material flow during the process. Furthermore, microstructural analysis is performed for the steel layer using a scanning electron microscope and Vickers microhardness tester to understand the variation in its grain structure and hardness. Results from the finite element model and …

Computational Investigation Of The Post-Yielding Behavior Of 3d-Printed Polymer Lattice Structures, Abdalsalam Fadeel, Hasanain Abdulhadi, Golam Newaz, Raghavan Srinivasan, Ahsan Mian

Mechanical and Materials Engineering Faculty Publications

Sandwich structures are widely used due to their light weight, high specific strength, and high specific energy absorption. Three-dimensional (3D) printing has recently been explored for creating the lattice cores of these sandwich structures. Experimental evaluation of the mechanical response of lattice cell structures (LCSs) is expensive in time and materials. As such, the finite element analysis (FEA) can be used to predict the mechanical behavior of LCSs with many different design variations more economically. Though there have been several reports on the use of FEA to develop models for predicting the post-yielding stages of 3D-printed LCSs, they are still …

High-Order Wave-Damage Interaction Coefficients (Wdic) Extracted Through Modal Decomposition, Hanfei Mei, Victor Giurgiutiu

Faculty Publications

This paper presents a new technique for the extraction of high-order wave-damage interaction coefficients (WDIC) through modal decomposition. The frequency and direction dependent complex-valued WDIC are used to model the scattering and mode conversion phenomena of guided wave interaction with damage. These coefficients are extracted from the harmonic analysis of local finite element model (FEM) mesh with non-reflective boundaries (NRB) and they are capable of describing the amplitude and phase of the scattered waves as a function of frequency and direction. To extract the WDIC of each wave mode, all the possible propagating wave modes are considered to be scattered …

Development Of A Finite Element Model Of The Stamping Process To Predict The Natural Frequencies Of Dimpled Beams, Varad Vasudeo Pendse

Masters Theses

Creating dimples on beams has been proven to be an effective way of altering their vibrational behavior. The objective of this research is to simulate the process of stamping using the finite element (FE) method to create a model of a dimpled beam. This dimple has non-uniform thickness, so it shows close agreement with its real-life counterpart.

ANSYS® Parametric Design Language (APDL) is used to build a three-dimensional (3-D) finite element model and simulate the process of stamping used to create the dimple. The structural simulation is validated by calculating the thickness and width of the deformed geometry of the …

Evaluation Of High Velocity Wear, Armando Deleon

Theses and Dissertations

The HHSTT located at Holloman Air Force Base conducts hypersonic testing in a unique way. Rather than perform cost prohibitive flight testing or hypersonic wind tunnel testing, a rocket-powered sled propels test articles down a track. This test setup has been used to test at speeds up to 2885 m/s (~Mach 8.6). The sled is kept on the rails by utilizing slippers, fabricated to wrap around the rail [1]. This slipper design keeps the sled from separating from the rail during a test due to the airflow producing lift, in a designed effort to minimize the wear that occurs during …

Damage Characterization Of Aircraft Fuselage Using Vibrothermography Technique-Review And Analysis, Abbasali Saboktakin

International Journal of Aviation, Aeronautics, and Aerospace

Vibrothermogrphy is a promising non-destructive technique that uses ultrasonic elastic waves to detect damages and is typically applied in the aerospace and automotive industries. This technique allows for defect selective imaging using thermal waves that are generated by ultrasound waves. In this paper, vibrothermography technique was applied to the aircraft fuselage to detect its damage. The influence of the damage on the temperature distribution at the damage region on the aluminum was investigated by finite element technique. Comprehensive understanding in edge crack in fuselage heating caused by local friction between crack surfaces was obtained.

Better Understanding Of Resonance Through Modeling And Visualization, Daniel O. Ludwigsen, Cayla Jewett, Matthew Jusczcyk

Daniel Ludwigsen

Students encounter cavity resonance and waveguide phenomena in acoustics courses and texts, where the study is usually limited to cases with simple geometries: parallelepipeds, cylinders, and spheres. Long-wavelength approximations help with situations of more complexity, as in the classic Helmholtz resonator. At Kettering University, we are beginning to employ finite element modeling in our acoustics classes to help undergraduates better understand the acoustic modes of actual structures. This approach to the time-independent wave equation (the Helmholtz equation) was first used in a research and measurements class to investigate two classic resonance problems. The first problem was a study of resonance …

Primary Blast Waves Induced Brain Dynamics Influenced By Head Orientations, Yi Hua, Yugang Wang, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

There is controversy regarding the directional dependence of head responses subjected to blast loading. The goal of this work is to characterize the role of head orientation in the mechanics of blast wave-head interactions as well as the load transmitting to the brain. A three-dimensional human head model with anatomical details was reconstructed from computed tomography images. Three different head orientations with respect to the oncoming blast wave, i.e., front-on with head facing blast, back-on with head facing away from blast, and side-on with right side exposed to blast, were considered. The reflected pressure at the blast wave-head interface positively …

Development Of A Finite Element Pelvis And Lower Extremity Model With Growth Plates For Pediatric Pedestrian Protection, Ming Shen

Wayne State University Dissertations

Finite element (FE) model is a useful tool frequently used for investigating the injury mechanisms and designing protection countermeasures. At present, no 10 years old (YO) pedestrian FE model has been developed from appropriate anthropometries and validated against limitedly available impact response data. A 10 YO child FE pelvis and lower extremities (PLEX) model was established to fill the gap of lacking such models in this age group. The baseline model was validated against available pediatric postmortem human subjects (PMHS) test data and additional scaled adult data, then the PLEX model was integrated to build a whole-body FE model representing …

Simulation Of Superplastic Forming Of Circular Edge-Welded Envelopes, Olga Tulupova

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modeling On Tail Pinch In Finishing Rolls During Hot Strip Rolling, Jong-Ning Aoh, Han-Kai Hsu, Ming-Fa Chen

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Fine Element Simulation Of A Modified Fine-Blanking Process To Eliminate The Die-Roll Size, Lin Hua, Bo Tang, Yanxiong Liu, Huajie Mao

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Effect Of Void Fraction On Transverse Shear Modulus Of Advanced Unidirectional Composites, Jui-He Tai

USF Tampa Graduate Theses and Dissertations

In composite materials, transverse shear modulus is a critical moduli parameter for designing complex composite structures. For dependable mathematical modeling of mechanical behavior of composite materials, an accurate estimate of the moduli parameters is critically important as opposed to estimates of strength parameters where underestimation may lead to a non-optimal design but still would give one a safe one.

Although there are mechanical and empirical models available to find transverse shear modulus, they are based on many assumptions. In this work, the model is based on a three-dimensional elastic finite element analysis with multiple cells. To find the shear modulus, …

Modeling Of Frame Structures Undergoing Large Deformations And Large Rotations, Hui Liu

Open Access Dissertations

Numerical simulation of large-scale problems in structural dynamics, such as structures subject to extreme loads, can provide useful insights into structural behavior while minimizing the need for expensive experimental testing for the same. These types of problems are highly non-linear and usually involve material damage, large deformations and sometimes even collapse of structures. Conventionally, frame structures have been modeled using beam-frame finite elements in almost all structural analysis software currently being used by researchers and the industry. However, there are certain limitations associated with this modeling approach. This research focuses on two issues, in particular, of modeling frame structures undergoing …

Modeling Picking On Pharmaceutical Tablets, Shrikant Swaminathan

Open Access Dissertations

Tablets are the most popular solid dosage form in the pharmaceutical industry because they are cheap to manufacture, chemically and mechanically stable and easy to transport and fairly easy to control dosage. Pharmaceutical tableting operations have been around for decades however the process is still not well understood. One of the common problems faced during the production of pharmaceutical tablets by powder compaction is sticking of powder to the punch face, This is known as 'sticking'. A more specialized case of sticking is picking when the powder is pulled away form the compact in the vicinity of debossed features. In …

Thermal Shock Studies On Carbon-Carbon Composites: Experimentation And Analysis, Alma Lucia Leanos

Open Access Theses & Dissertations

The oxidation behavior of C/C composites under thermal shock conditions in air is understood and predicted experimentally and by computational efforts. In Chapter. 1, both compressive properties and oxidation behavior of pristine and thermal shock exposed 2D C/C composite specimens were examined. Pristine test specimens were exposed to thermal shock conditions with temperatures ranging from 400°C to 1000°C in an oxidizing environment, followed by compression tests on pristine and thermal shock exposed specimens to obtain their compressive responses.

Similarly, in Chapter. 2, the influence of thermal shock conditions on both, the extent of carbon materials decomposition and the through-thickness compressive …

Computational Investigation Of Injectable Treatment Strategies For Myocardial Infarction, Hua Wang

Theses and Dissertations--Mechanical Engineering

Heart failure is an important medical disease and impacts millions of people throughout the world. In order to treat this problem, biomaterial injectable treatment injected into the myocardium of the failing LV are currently being developed. Through this treatment, the biomaterial material injections can reduce wall stresses during the cardiac remodeling process. By using computational techniques to analyze the effects of a treatment involving the injection of biomaterial material into the LV after MI, the material parameters of the hydrogel injections can be optimized. The results shows that the hydrogel injections could reduce the global average fiber stress and the …

The Characterization Of The Effects Of Stress Concentrations On The Mechanical Behavior Of A Micronic Woven Wire Mesh, Steven Kraft

Electronic Theses and Dissertations

Woven structures are steadily emerging as excellent reinforcing components in dualphase composite materials subjected to multiaxial loads, thermal shock, and aggressive reactants in the environment. Metallic woven wire mesh materials display good ductility and relatively high specific strength and specific resilience. While use of this class of materials is rapidly expanding, significant gaps in mechanical behavior classification remain. This thesis works to address the mechanics of material knowledge gap that exists for characterizing the behavior of a metallic woven structure, composed of stainless steel wires on the order of 25 microns in diameter, and subjected to various loading conditions and …

Numerical And Experimental Investigation Of Vascular Suture Closure, Linxia Gu, Ananth Ram Mahanth Kasavajhala, Haili Lang, James M. Hammel

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose — In order to optimize the performance of the suture for tissue closure, it is essential to develop strategies for devising new and improved techniques that can visualize and compare various suturing techniques. This paper describes an experimental and numerical investigation on the performance of sutured tissue.

Methods — In the experiments, two pieces of glutaraldehyde cross-linked bovine pericardium were sutured together through simple running suture and tensioned to study the performance of the sutured tissue. During testing, the tension load and the total displacement of the specimen were recorded. The strain field of the specimen was simultaneously captured …

Computationally Efficient Finite Element Models Of The Lumbar Spine For The Evaluation Of Spine Mechanics And Device Performance, Sean D. Smith

Electronic Theses and Dissertations

Finite Element models of the lumbar spine are commonly used for the study of spine mechanics and device performance, but have limited usefulness in some applications such as clinical and design phase assessments due to long analysis times. In this study a computationally efficient L4-L5 FSU model and a L1-Sacrum multi-segment model were developed and validated. The FSU is a functional spine unit consisting of two adjacent vertebral bodies, in this case L4 and L5. The multi-segment model consists of all lumbar vertebrae and the sacrum. The models are able to accurately predict spine kinematics with significantly reduced analysis times, …

Adaptive Surrogate Modeling For Efficient Coupling Of Musculoskeletal Control And Tissue Deformation Models, Jason P. Halloran, Ahmet Erdemir, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Background

Finite element (FE) modeling and multibody dynamics have traditionally been applied separately to the domains of tissue mechanics and musculoskeletal movements, respectively. Simultaneous simulation of both domains is needed when interactions between tissue and movement are of interest, but this has remained largely impractical due to high computational cost.

Method of Approach

Here we present a method for concurrent simulation of tissue and movement, in which state of the art methods are used in each domain, and communication occurs via a surrogate modeling system based on locally weighted regression. The surrogate model only performs FE simulations when regression from …

Explicit Finite Element Modeling Of Knee Mechanics During Simulated Dynamic Activities, Mark A. Baldwin

Electronic Theses and Dissertations

The natural knee is one of the most commonly injured joints in the body due to relatively high loads and motions that can lead to debilitating degenerative diseases such as osteoarthritis. Total knee arthroplasty is a clinically successful method for eliminating pain in the osteoarthritic knee, but is subject to complications that can affect patient satisfaction and long-term implant performance. The work presented in this dissertation is a demonstration of how anatomic three-dimensional (3D) computational knee models can be an effective alternative for investigating knee mechanics when compared to the cost and time prohibitive nature of in-vivo and in-vitro methods. …

Better Understanding Of Resonance Through Modeling And Visualization, Daniel O. Ludwigsen, Cayla Jewett, Matthew Jusczcyk

Physics Presentations And Conference Materials

Students encounter cavity resonance and waveguide phenomena in acoustics courses and texts, where the study is usually limited to cases with simple geometries: parallelepipeds, cylinders, and spheres. Long-wavelength approximations help with situations of more complexity, as in the classic Helmholtz resonator. At Kettering University, we are beginning to employ finite element modeling in our acoustics classes to help undergraduates better understand the acoustic modes of actual structures. This approach to the time-independent wave equation (the Helmholtz equation) was first used in a research and measurements class to investigate two classic resonance problems. The first problem was a study of resonance …