Mechanical Engineering Commons^™

Simulation Of Vertical Axis Wind Turbines With Variable Pitch Foils, L. Damon Woods, John F. Gardner, Kurt S. Myers

Mechanical and Biomedical Engineering Faculty Publications and Presentations

A dynamic computer model of a turbine was developed in MATLAB in order to study the behavior of vertical axis wind turbines (VAWTs) with variable pitch (articulating) foils. The simulation results corroborated the findings of several empirical studies on VAWTs. The model was used to analyze theories of pitch articulation and to inform the discussion on turbine design. Simulations of various models showed that pitch articulation allowed Darrieus-style vertical axis wind turbines to start from rest. Once in motion, the rotor was found to accelerate rapidly to very high rotational velocities. The simulations revealed a plateau region of high efficiency …

Thin Electrical Double Layer Simulation Of Micro-Electrochemical Supercapacitors, Kaitlyn Fisher, Guoping Xiong, Timothy S. Fisher

The Summer Undergraduate Research Fellowship (SURF) Symposium

The deteriorating state of the environment has drawn many people to hybrid electric vehicles. Electrochemical micro-supercapacitors are of interest in this field because of their high power density relative to other micro-power sources. However, little is known about how the properties of the electrolyte used affect the performance of such devices. The first step of this investigation was to use thermoreflectance microscopy to measure the temperature change of the electrodes while charging and discharging supercapacitor samples. The components of these samples were graphitic petal electrodes with a Ti/Au covering (for enhanced light reflectance) on a SiO₂ base, with a …

Mems Lab Simulation Tool, Oluwatosin D. Adeosun, Sambit Palit, Ankit Jain, Muhammad A. Alam

The Summer Undergraduate Research Fellowship (SURF) Symposium

MEMS actuators have multiple design applications. Understanding their behavior as well as the ability to predict their actuation characteristics and voltage response is important when designing these actuators. In order to know these devices will behave, designers have to solve multiple analytical equations and experiments that can be very time consuming. Over the course of the summer a tool was created on nanoHUB that will allow users to enter information about a MEMS actuator and provide the voltage response of the actuator. To create the tool, scaling equations were first provided for various geometry configurations and the equations were next …

Kinetic Monte Carlo Simulations, Jingyuan Liang, R. Edwin García, Ding-Wen (Tony) Chung, David Ely

The Summer Undergraduate Research Fellowship (SURF) Symposium

Kinetic Monte Carlo (kMC) is a set of scientific libraries designed to deploy kMC simulations intended to simulate the time evolution of some processes occurring in nature. kMC is currently allows the user to intuitively generate single component crystal lattices to simulate, post process, and visualize the kinetic Monte Carlo-based atomistic evolution of materials. kMC provides an interface to the Stochastic Parallel PARticle Kinetic Simulator (SPPARKS) [1] and is specifically designed to simulate individual atomic deposition (condensation) and dissolution (evaporation) events, while simultaneously tracking the surface and bulk crystallographic anisotropic diffusion. The main goal of this project is to create …

The Stability And Control Of The Single Track Vehicles, Shyngys Karimov, Martin Corless

The Summer Undergraduate Research Fellowship (SURF) Symposium

Bicycles, motorcycles and scooters are all examples of the single track vehicles. The dynamics of the single track vehicle involve many degrees of freedom and various modes which govern its performance, making a complicated and interesting research topic. Motorcycle in motion can roll, yaw, and steer about the steering axis. It has three main modes which determine the motion and stability of it, they are weave, capsize, and wobble. The motorcycle performance is limited by the behavior of its modes, and if even one of the modes becomes unstable, the vehicle will roll over, and crash. The goal of this …

Technical Subtopic 2.1: Modeling Variable Refrigerant Flow Heat Pump And Heat Recovery Equipment In Energyplus, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

The University of Central Florida/Florida Solar Energy Center, in cooperation with the Electric Power Research Institute and several variable-refrigerant-flow air conditioning (VRF AC) manufacturers, provided a detailed computer model for a VRF AC system in the United States Department of Energy's (U.S. DOE) EnergyPlus' building energy simulation tool. No other simulation tool currently has the capability to accurately model this state-of-the-art VRF heating, ventilating, and air conditioning (HVAC) equipment. Detailed laboratory testing and field demonstrations were performed to measure equipment performance and compare this performance with that predicted by the use of this new model through computer simulation.

This project …

Computational Modeling And Experimental Study On Optical Microresonators Using Optimal Spherical Structure For Chemical Sensing, Hanzheng Wang, Lei Yuan, Jie Huang, Xinwei Lan, Cheol-Woon Kim, Lan Jiang, Hai Xiao

Electrical and Computer Engineering Faculty Research & Creative Works

Chemical sensors based on optical microresonators have been demonstrated highly sensitive by monitoring the refractive index (RI) changes in the surrounding area near the resonator surface. In an optical resonator, the Whispering Gallery Modes (WGMs) with high quality (Q) factor supported by the spherical symmetric structure interacts with the contiguous background through evanescent field. Highly sensitive detection can be realized because of the long lifetime of the photons. The computational models of solid glass microspheres and hollow glass spheres with porous wall (PW-HGM) were established. These two types of microresonators were studied through simulations. The PWHGM resonator was proved as …

Aspen Plus Simulation Of Biomass Gasification In A Steam Blown Dual Fluidised Bed, Wayne Doherty, Anthony Reynolds, David Kennedy

Book/Book Chapters

The efficient utilisation of biomass resources is of utmost importance. Biomass gasification offers much higher efficiencies than combustion. Gasification is a process in which a fuel is converted to a combustible gas (syngas). A dual fluidised bed gasifier known as the fast internally circulating fluidised bed (FICFB) was selected. It has been demonstrated at industrial scale and data is readily available for model validation. An Aspen Plus model was developed to simulate the FICFB gasifier. The model is based on Gibbs free energy minimisation and the restricted equilibrium method was used to calibrate it. The model has been validated and …

Real-Time Visualization Of Finite Element Models Using Surrogate Modeling Methods, Ryan C. Heap

Theses and Dissertations

Finite element analysis (FEA) software is used to obtain linear and non-linear solutions to one, two, and three-dimensional (3-D) geometric problems that will see a particular load and constraint case when put into service. Parametric FEA models are commonly used in iterative design processes in order to obtain an optimum model given a set of loads, constraints, objectives, and design parameters to vary. In some instances it is desirable for a designer to obtain some intuition about how changes in design parameters can affect the FEA solution of interest, before simply sending the model through the optimization loop. This could …

Thermo-Piezo-Electro-Mechanical Simulation Of Algan (Aluminum Gallium Nitride) / Gan (Gallium Nitride) High Electron Mobility Transistor, Lorin E. Stevens

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Due to the current public demand of faster, more powerful, and more reliable electronic devices, research is prolific these days in the area of high electron mobility transistor (HEMT) devices. This is because of their usefulness in RF (radio frequency) and microwave power amplifier applications including microwave vacuum tubes, cellular and personal communications services, and widespread broadband access. Although electrical transistor research has been ongoing since its inception in 1947, the transistor itself continues to evolve and improve much in part because of the many driven researchers and scientists throughout the world who are pushing the limits of what modern …

Development Of Cfd Models For The Purposes Of Exploring Free Surface Wave Phenomena, Leonard P. Stoehr

Masters Theses

With the push for finding alternative, green energy sources, the harnessing of energy from ocean and lake waves is becoming a more researched field. To fully understand the behavior of wave interactions and optimize designs to extract this energy, it is necessary to develop computer models that can accurately replicate this behavior. A case is presented in which previous work done using the wave tank found in the Western Michigan University fluids lab is examined. The case involves harnessing the energy generated by ocean waves through the usage of plates of different shapes resting horizontally on the water’s surface. The …

Optimization Of Mixing In A Simulated Biomass Bed Reactor With A Center Feeding Tube, Michael T. Blatnik

Masters Theses 1911 - February 2014

Producing gasoline-type fuels from lignocellulosic biomass has two advantages over producing alcohol-type fuels from plant sugars: gasoline has superior fuel characteristics and plant lignin/cellulose does not compete with human food supplies. A promising technology for converting lignocellulose to fuel is catalytic fast pyrolysis (CFP). The process involves injecting finely ground biomass into a fluidized bed reactor (FBR) at high temperatures, which reduce the biomass to gases that react inside the catalyst particles. This entails complex hydrodynamics to efficiently mix a stream of biomass into a catalyst bed that is fluidized by a separate stream of inert gas. Understanding the hydrodynamics …

Development Of An In Situ Measurement Device For Obtaining Material Thermal Properties, Mark A. Hepokoski

Dissertations, Master's Theses and Master's Reports - Open

This thesis presents a methodology for measuring thermal properties in situ, with a special focus on obtaining properties of layered stack-ups commonly used in armored vehicle components. The technique involves attaching a thermal source to the surface of a component, measuring the heat flux transferred between the source and the component, and measuring the surface temperature response. The material properties of the component can subsequently be determined from measurement of the transient heat flux and temperature response at the surface alone. Experiments involving multilayered specimens show that the surface temperature response to a sinusoidal heat flux forcing function is also …

Dynamic Simulation Of Turbine Engine Used With Molten Carbonate Fuel Cell For Power Generation In The Megawatt Range, Carlos Eduardo Gutierrez

Browse all Theses and Dissertations

Molten carbonate fuel cells (MCFC) have a high operating temperature of approximately 650° C (1200° F) to achieve sufficient conductivity of its carbonate electrolyte. Therefore, a gas turbine engine coupled with a MCFC is desirable since the turbine engine can be used to provide hot gas to the cathode, and the cathode gas residue can be used to raise the temperature of the natural gas and water vapor mixture (fuel) before it enters the MCFC at the anode. Dynamic models of a hybrid power plant consisting of a gas turbine engine and a MCFC with their respective components were developed …

Modeling And Simulation Of Surface Profile Forming Process Of Microlenses And Their Application In Optical Interconnection Devices, Zhengyu Miao

LSU Doctoral Dissertations

Free space micro-optical systems require to integrate microlens array, micromirrors, optical waveguides, beam splitter, etc. on a single substrate. Out-of-plane microlens array fabricated by direct lithography provides pre-alignment during mask fabrication stage and has the advantage of mass manufacturing at low cost. However, this technology requires precise control of the surface profile of microlenses, which is a major technical challenge. The quality control of the surface profile of microlenses limits their applications. In this dissertation, the surface forming process of the out-of-plane microlenses in UV-lithography fabrication was modeled and simulated using a simplified cellular automata model. The microlens array was …